-
Product
High Density I/O Boards
-
NAI offers, and continues to introduce, high density multifunction or combination-function I/O boards designed for a specific application or purpose. Based on the specialized application itself, from the interface connectors through the motherboard, to the specific function, these boards typically address I/O function integration challenges requiring higher current capacity, layout, and/or grounding requirements that are not available in our standard I/O boards. They are specifically designed for rugged defense, commercial aerospace, and industrial applications.
-
Product
LVDT I/O Cards
CPE4000
-
Computer Conversions Corporation
Computer Conversions’ CPe4000 Series are CompactPCI-Express (cPCIe) and PXI Express (PXIe) compliant: Synchro, Resolver, and LVDT/RVDT I/O Cards (predominantly output cards), with GEN1 and GEN 2 PCI Express interface, designed for accurate and reliable commercial, industrial and COTS-Mil. applications in test, simulation, motion control and shipboard data distribution. The CPe4000 Series drive up to 4 channels of Synchro, Resolver, 3-wire LVDT/RVDT outputs, or up to 8 channels of 2 wire LVDT/RVDT AC Sensor output sets.
-
Product
Digital I/O Software And Training
-
High-speed and static 3U and 6U PXI and PCI digital I/O instrumentation. Offering test rates to 200 MHz and programmable logic levels of -10 V to +15 V, our digital products feature the highest performance and most cost effective digital test solutions in the industry.
-
Product
Jitter Free I/O Access Fast Data Acquisition
TiCoBasic
-
Shortest available reaction time for fast data acquisition, open- and closed-loop control! This focus of Jger Messtechnik is greatly intensified by the new TiCo processor, which enables real-time processing in the scale of nanoseconds. The TiCo (Timing Controller) being implemented into a Xilinx FPGA enhances the approved ADwin systems by a close-to-I/O, extremely fast pre-processing.
-
Product
16-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-8
-
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
OMNIBUS Analog I/O Modules
-
I/O Mezzanine cards for Modular, Solomente & Data Acquisition boards
-
Product
PCI Digital I/O and Relay Driver Cards
-
a 32-channel Digital I/O card with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel.
-
Product
PXI Digital I/O And Prototyping Modules
Prototyping Module
Programmable Input Threshold and High-Side or Low-Side Drive Capability Available on Some ModulesOptically Isolated Input/Output for Interfacing to Electrically Noisy Environments Available on Some ModulesTTL Inputs and Outputs Suitable for Interfacing to External LogicOpen Collector/Drain Transistor Output Versions Suitable for Driving Internal or External Relay Coils
-
Product
Serial I/O Expansion
PCM-CAN
-
WINSYSTEMS’ PCM-CAN-2-ISO is a PC/104-compliant, isolated Controller Area Network (CAN Bus) peripheral module. This board uses two NXP SJA-1000 CAN controller ICs with advanced features for use in automotive and industrial applications.
-
Product
I/O Wiring Cable
PCL Series
-
I/O wiring cable sets are designed for easy field wiring capabilities. The PCL-1050 I/O wiring cable series can be used with multiple I/O cards.
-
Product
Analog I/O Module
DS-MPE-DAQ0804
-
The DS-MPE-DAQ0804 is a rugged, low cost data acquisition PCIe MiniCard module with both analog and configurable digital I/O. It is ideal for adding analog I/O and digital I/O features to embedded and OEM applications requiring low cost, small size, and/or light weight.
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 5V-HS
APCIE-1564-5V-HS
-
32 digital inputs, 5 V, isolated16 interruptible inputs32 digital outputs, 5 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
PCIe-7851, Virtex-5 LX30 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device
781102-01
Multifunction Reconfigurable I/O
Virtex-5 LX30 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device - The PCIe‑7851 features a user-programmable FPGA for high performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7851 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
-
Product
PoE Ethernet I/O Module w/ 3-axis Encoder/Counter Inputs
PET-7083
-
A great device, that works well for building automation, factory, and machine automation, remote maintenance, testing, and diagnosis, the PET-7083 is a 3-axis high speed encoder/counter module. Its each axis can be individually configured for Quadrant, Pulse/Direction or CW/CCW counting modes. The maximum input rate for Quadrant counting mode is 1 MHz, and for Pulse/Direction, CW/CCW counting modes is 4 MHz. The encoder/counter module is equipped a FRAM to retain the counter value after it is powered off. FRAM is a nonvolatile memory that can hold written data even after it is powered off. The data retention can be 10 years. And the feature can be configured as enabled or disabled.
-
Product
PCI Analog IO Board
MS 1803
-
*Bus Interface:- PCI Bus*Analog Inputs:- 16 Single Ended Inputs / 8 Differential Ended Inputs*Input Resolution:- 16 Bits*Input Range:- ±10V*Gain:- Programmable Gain Control (1, 2, 4, 8, 16)*Sampling Rate up to 100Ks/S*Peak Measurement +ve and -ve peak for all input channels
-
Product
Programmable RS-232, IR, and I/O Controller
HR-4P
-
The Model HR-4P is a programmable RS-232 device designed for control & automation of a Projector, LCD, or any other device with serial or IR port.
-
Product
64-Ch Isolated Digital I/O PCIE Card
PCIE-1756
-
Wide output range (5 ~ 40 VDC)High sink current on isolated output channels (500mA max./ch)Wide input range (10 ~ 30 VDC)High-voltage isolation (2,500 VDC)Interrupt handling capability2,000 VDC ESD protectionEither +/- voltage input for DI by groupHigh over-voltage protection (70 VDC)Output status read-backKeeps the output settings and values after system hot resetChannel-freeze function
-
Product
4-Axis Quadrature Encode/Counter Universal PCI Card With 8-Ch Isolated Digital I/O
PCI-1784U
-
Four 32-bit up/down countersSingle ended or differential inputsPulse/direction and up/down counterx1, x2, x4 counts for each encoder cycleMultiple interrupt sources for precision application4-stage digital filter with selectable sampling rateOn-board 8-bit timer with wide range time-base selectorOptically isolated up to 2,500 VDC4 isolated digital input4 isolated digital outputBoardID™ switch
-
Product
Multifunctional I/O Module
DP-OBC-1122
-
DP-OBC-1122 is a standard 3U cPCI Multi-Functional IO module. This board operates on 32bit, 33MHz PCI bus. The key function of the module is to provide analog IO interface, in addition to the various communication interfaces such as ARINC429, RS422 and Rs232.It has an ADC, operating with ±10V analog input catering for 8 single ended / 4 differential ended channels and a DAC which provides 4 channels of analog signals with a maximum output voltage of ±10V .The module also features standard communication channels and general purpose IOs.
-
Product
32-CH I/O Terminal Base
HSL-TB32-M-DIN
-
*Field I/O wiring connection for HSL I/O modules*Spring terminal for easy field wiring*Power and ground included for each signal channel*Interlocking design for rugged installation*Power LED indicator*DIN rail mounting
-
Product
OPC UA Ethernet I/O Modules
ADAM-6300
-
Industrial OPC UA Ethernet I/O Modules with Modbus protocol converge OT/IT with security, linking to SCADA and the cloud for remote monitoring.
-
Product
miniPCIe IO and Processing Module
Solar Express 50 (SE50)
-
Sundance Multiprocessor Technology Ltd.
The SE50 Mini PCIe card is a small form factor board used to implement the PCI Express interface to expand embedded PC I/O. The card size is 30mm wide by 50.95mm long.
-
Product
PIM-Parallel-IO
-
The PIM-Parallel-IO facilitates rear panel IO in cPCI based systems using PMC's. The PIM-Parallel-IO provides the PMC_Parallel_IO front panel IO where rear panel IO is desired. The PIM-Parallel-IO can be used with other PMCs as well.
-
Product
PXIe-6375, 208 AI (16-Bit, 3.8 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module
783634-01
Multifunction I/O
PXIe, 208 AI (16-Bit, 3.8 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6375 offers analog I/O, digital I/O, and four 32‑bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6375 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
LVDT I/O Cards
IB
-
Computer Conversions Corporation
The "IB Series" product line are full size IBM PC/AT+ and ISA 2.01 compatible synchro, resolver, and LVDT I/O cards, and resolver-sensor card sets used as absolute encoder systems.
-
Product
16-bit, 100KHz, 8SE/4DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, all isolated
CPCI-3120-8-4
-
Input range:- ± 10 V, 0-10 V software programmable- 0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V,- ± 1 V (gain)- 0-20 mA (option)- software-programmable amplifier:- PGA x1, x2, x5, x10- Conversion triggered through software,scan, timer, external event- Onboard FIFO buffering for 256 analog values- Data exchange through 16-bit I/O or 32-bit memory (PCI DMA)- Sequence RAM- Overvoltage protection- input filter: 160 kHz
-
Product
96-Ch Digital I/O PCIE Card
PCIE-1753
-
Fully compatible with PCI-1753Up to 96 TTL digital I/O linesEmulates mode 0 of 8255 PPISupports both dry and wet contactInterrupt handling capabilityOutput status read-backSupports input data pattern match and change of state functionsKeep I/O settings and output status after hot resetBuffered circuits for higher driving capacity than the 8255High-density 100-pin SCSI connector
-
Product
Industry Pack Carriers and Digital I/O
CPCI-4pack-6U
Digital I/O Module
The CPCI-4pack-6U module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-4pack-6U is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSPvia the CPCI bus or the local serial port.
-
Product
Distributed I/O
-
Schweitzer Engineering Laboratories, Inc.
Expand the I/O of SEL relays and communications processors, reduce copper in substations by transferring I/O from remote locations over fiber, and provide electrical isolation to avoid ground paths and induced noise and interference.
