-
Product
PXI-6515, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Outputs, Bank-Isolated PXI Digital I/O Module
778964-01
Digital I/O Module
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6515 is an industrial digital I/O interface with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Rugged Analog I/O Modules
-
Our extensive line of analog I/O modules currently includes PC/104, PCIe MiniCard and FeaturePak form-factor products, providing both A/D and D/A functions. Most of these products also include digital I/O and counter/timer features. A unique feature of Diamond analog I/O modules is our patented autocalibration technology, which can reduce analog measurement errors by up to 10 times relative to conventional designs.
-
Product
PXI-6254, 32 AI (16-Bit, 1 MS/s), 48 DIO, PXI Multifunction I/O Module
779118-01
Multifunction I/O
The PXI-6254 offers analog input, correlated digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Virtex-5 FPGA with Plug-in I/O
PMC-VFX
-
Acromag’s PMC-VFX boards feature a reconfigurable Xilinx® Virtex™-5 FPGA enhanced with multiple high-speed memory buffers and a high-throughput PCI-X interface. Field I/O interfaces to the FPGA via the rear J4/P4 connector and/or with optional front mezzanine plug-in I/O modules.
-
Product
A PoE-PD I/O Board
AX93274
-
*PoE-PD I/O board complies with IEEE802.3at standard via an internal cable to power on SBC*100 x 32 mm*1 x LAN cable, 1 x power cable, 1 x thermal module*Compliant products: PICO831, PICO121, PICO841, PICO843
-
Product
Analog I/O and Digital Receivers
-
Curtiss-Wright Defense Solutions
Many mission-critical applications require small form factor solutions, but cannot compromise ruggedization requirements or I/O and processing performance. Our VPX, XMC, PMC and FMC module-based sensor I/O solutions are designed to handle the toughest operating environments while packing maximum functionality in a minimal physical footprint.
-
Product
Multifunction Analog I/O Board
104-AIO12-8
-
*Eight true differential inputs, or eight single-ended inputs optional*Programmable input ranges of: 0-5V, 0-10V, ±5V, ±10V*100KHz sampling rate*On-board pacer clock and counter timers*Four double-buffered analog outputs*Jumper selectable output ranges of: 0-5V, 0-10V, ±5V, ±10V*24 digital I/O lines, type 82C55 with change of state detect on port C, buffers on ports A & B*Flexible configurations to suit your needs
-
Product
SWaP Optimized Processing and Multifunction I/O & Communications System
NIU3A
Multifunction I/O
The NIU3A is a small, rugged, low-power, self-contained processing and multifunction I/O system preconfigured with 24-CH programmable Discrete I/O, 8-CH ARINC 429/575, 4-CH CANBus and 2-CH MIL-STD-1553 functions. The NIU3A can also be configured with up to three smart Configurable Open Systems Architecture™ (COSA®) function modules. The NIU3A boasts Dual or Quad Core ARM Cortex®-A53 processors for customer software applications and I/O and communications management. The NIU3A is configured with two 10/100/1000BASE-T (GbE) Ethernet ports and an RS-232 port for maintenance / diagnostic or configuration interface. Ideally suited for rugged Mil-Aero applications, the NIU3A delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
Digital I/O Board
P104-DIO-96
-
Each I/O line of this card is buffered and capable of sourcing 32mA, or sinking 64mA. The board simulates Programmable Peripheral Interface chips (PPI) to provide a computer interface to digital I/O lines. Each PPI supports two 8-bit ports (A, B) and two 4-bit ports (Chi, Clow). Each port can be configured to function as either input or output latches. The I/O line buffers (types 74ABT240 and 74ABT245) are configured automatically by hardware logic for input or output according to the PPI Control Register direction software assignment.
-
Product
Mezzanine FPGA I/O Module
ADC-MOD2
-
Curtiss-Wright Defense Solutions
Simple analog input to a processor is no longer enough. Software Defined Radio (SDR), RADAR, and telecommunications applications demand closely coupled high performance processing.
-
Product
Dynamic Digital I/O (3U), 16 Ch., Per Pin Control, Up To 200 MHz W/256MB Memory & LVDS
GX5293
Digital I/O Module
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.Dynamic Digital I/O (3U), 16 ch., per Pin Control, up to 200 MHz w/256MB Memory & LVDS
-
Product
as an 8 bit I/O Port
BL233
-
The BL232 has 2 commands that let you use its pins directly. If you aren't using the I2C bus, this gives you and easy 8 bit I/O port
-
Product
Digital I/O Card
-
Axiomtek's digital I/O cards feature TTL I/O, isolated I/O, relay output, and timer/counter, and supports high-density on a single board, making them specifically suitable for factory automation, industrial ON/OFF control and switch status sensing.
-
Product
Remote I/O
-
ADLINK remote IO and serial communication cards are suitable for handling multiple digital signal types for IoT and other industrial applications such as facility monitoring, environmental monitoring, and industrial process control.Remote IO - NuDAM modules provide direct communication with various sensors, including performing signal conditioning, scaling, linearization and conversion to obtain temperature, pressure, flow, voltage, and current measurements. The new ND6100 series modules use Modbus/RTU remote data transmission protocols, providing customers with a comprehensive product portfolio. ADLINK's serial communication cards provide a PCI/PCIe interface and support RS-232 and CAN communication interfaces, allowing customers to choose the most suitable communication card for various automation equipment needs.
-
Product
Digital I/O
-
With digital I/O cards, static or dynamic bit patterns can be generated or recorded. Each bit is assigned a control signal for an output and a sensor signal for an input. The usual voltage range for the inputs and outputs is between 2 V (TTL) and 24 V (automation).
-
Product
PXIe-7866, Kintex-7 325T FPGA, 24-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
787354-01
Multifunction Reconfigurable I/O
PXIe, Kintex-7 325T FPGA, 24-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module - The PXIe-7866 features flexibility of timing and synchronization with a user-programmable FPGA for onboard processing and direct control over I/O signals. The PXIe-7866 provides 24 analog output, 2 analog input, and 32, 5V input-tolerant digital I/O channels connected to a Kintex-7 325T FPGA to help you design applications for hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. You can use the dedicated A/D converter (ADC) for independent timing, individual channel triggering, and multirate sampling. Additionally, the PXIe-7866 includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
Product
96-Ch Digital I/O PCI Card
PCI-1753
-
Emulates mode 0 of 8255 PPIBuffered circuits for higher driving capacity than 8255Multiple-source interrupt handlingInterrupt output pin for simultaneously triggering external devices with the interruptOutput status read-back“Pattern match” and “Change of state” interrupt functions for critical I/O monitoringKeeps I/O setting and digital output values when hot system resetSupports dry contact and wet contactHigh-density 100-pin SCSI connector
-
Product
Cyclone II FPGA with Digital I/O
IP-EP200
-
This series of plug-in mezzanine modules provides a user-customizable Altera® Cyclone II FPGA on an Industry Pack (IP) module. The module allows users to develop and store their own instruction set in the FPGA for adaptive computing applications.
-
Product
Digital and Serial I/O
-
VadaTech’s wide range of ATCA Rear Transition Modules (RTMs) and MicroTCA I/O AMCs make it easier to integrate these standards-based building block systems into your network or application.
-
Product
PXIe-7822, PXI Express Digital RIO with Kintex-7 325T FPGA
783486-01
Digital I/O Module
Kintex 7 325T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7822 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7822 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7822 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
4AO/4DI Modbus RTU Remote I/O
ND-6124
Data Acquisition Module
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
-
Product
Digital IO
PA64IX
Digital I/O Module
The PA64IX represents a new level of performance and capabilities for PXI-based digital instrumentation. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 1024 bi-directional pins (16 boards). The PA64IX also supports dee pattern memory by offering 32 M of on-board vector memory with static per pin direction control and with test rates up to 33 MHz.
-
Product
FMC 5-Channel Digital I/O Module
FMC DIO
-
Sundance Multiprocessor Technology Ltd.
The fmc-dio-5chttla 5-channel digital I/O module is a simple board for digital I/O on LEMO connectors. It has been designed for testing White Rabbit functionality as part of the SPEC Demonstration Package for White Rabbit, and it can be used for other general purpose applications too.
-
Product
PXI 32 Channel I/O, High Side Driver
40-413-001
Digital I/O Module
A 32 channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only (shown here), alow side only and a combined high and low side each capable of driving 2A loads. Eachoutput is fully protected against over-voltage, over-current and thermal overload,ensuring robust and reliable operation in the toughest test environments. For highside voltage driving the high side voltage source is supplied from an external voltagesource, permitting the module to drive high capacity loads without impacting thePXI chassis power supply.
-
Product
USB-7845, Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783200-01
Multifunction Reconfigurable I/O
Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7845 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7845 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
Product
Relay I/O Module via Ethernet
2650
-
8 form-C mechanical relays with 240VAC, 2A ratingConnects to an Ethernet through 2601 hub100 mm DIN carrierResponds to interlock and E-stop circuitsWatchdog TimerCompatible with Linux and WindowsUse our design assistant to configure a system and calculate pricing
-
Product
Tri-Mode I/O Controller
SAS3808
-
Broadcom Tri-Mode SerDes technology enables seamless operation of PCIe, SAS or SATA storage devices in a single drive bay. The introduction of PCIe devices executing NVMe to the existing SAS/SATA infrastructure makes industry standard, hot-pluggable drive bays even more versatile. Whether you’re building external or cloud-based storage systems for high connectivity, or outfitting servers, the SAS3808, 8-port, 12Gb/s Tri-Mode SAS/SATA/PCIe Gen 4.0 IOC provides choices for storage optimization by enhancing direct-attached storage (DAS) solutions.
-
Product
USB Multifunction Digital I/O Module
Model JI-4040
-
The JI-4040 module is a versatile, easy-to-use device for adding universal digital I/O capability to acomputer system via a USB connection. The module is comprised of 36 bidirectional I/O channels and 2 Special Function Ports (SFP). The SFP can be software programmed as a variable duty-cycle clock/pulse generator, event counter, or interval/pulse timer. The I/O is selectable to interface 5.0 V, 3.3 V, 2.5 V, or 1.8 V systems. Host to module isolation eliminates ground-loops and provides protection from noise and switching transients on external signals. The JI-4040 is available as either a desktop unit or low-cost OEM board.
-
Product
Analog and Other I/O
-
Our I/O portfolio covers everything from simple discrete to high speed analog control and delivers flexibility, performance, reliability and connectivity.
-
Product
Digital I/O
-
User programmable 3U PXI FPGA cards for digital and mixed signal applications. Utilizing Altera FPGAs and incorporating a base board / expansion board architecture, our FPGA products offer users the flexibility to create high performance, customized digital and mixed signal instrumentation for specific applications without requiring the use of external interface cards.
