Transmittance
-
product
With SAT-IF input EDFA
HA4600/IF
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA4600/IF series, is narrow-band multiplexing EDFA suitable for L-Band fiber link application. With build-in 1550nm Internal Modulation SAT-IF optical transmitter, used for inter-cutting DBS. The WDM inside will multiply the signal from TX and main line signal that is inputted from outside, then the combined signal will enter EDFA to be amplified to serve the local subscribers. To avoid the interferes caused by mismatching of the optical output power between TX and main line signal from outside, output power of the TX can go through a VOA, thus, it can be adjusted or set from the front panel. This unit is simple and clear, easy to be installed and tested. It offers a high quality and cost-effective solution for inter-cutting DBS into full optic relay 1550nm fiber CATV system and second-stage service area.
-
product
EMCTD Broadband RF Safety Systems
The EMCTD analog Smart Fieldmeter® is easy to read and to operate. The EMCTD broadband electromagnetic probe covers the 0.2 to 3000 MHz spectrum where most common industrial, communications, medical and government RF emitters are found. The ANGPE-3000 system enables checking of home, office, and workplace RF levels. The system is designed to conveniently measure RF levels around WiFi access points, RFID systems and rooftop antennas; to find transmitter cabinet radiation, locate transmission line leaks, to identify non-radiating antenna elements, and much more. With the supplied NIST-traceable calibration, this system supports laboratory testing of RF devices in compliance with present EMC and RF safety standards.
-
product
Telemetry Transmitter
TT22 Series
Systems Engineering & Management Company
The TT22 series of 0.25W telemetry transmitters are designed to transmit data in the frequency bands covering 1710-1850 MHz or 2185-2485 MHz. These transmitters are true FM, modular, all solid state and are protected for operation into any VSWR, without damage, including open or short circuit.
-
product
Thermocouple Calibrators
Practical Instrument Electronics, Inc.
PIE has a thermocouple calibrator to fit your needs from the PIE 520B single type thermocouple simulator to the advanced troubleshooting capabilities of the PIE 422Plus. Have you had issues in the past where your thermocouple calibrator wouldn’t work with some of the instruments in your plant? Our thermocouple calibrators are guaranteed to be compatible with all process thermocouple inputs including all brands of smart temperature transmitters, PLC input cards, DCS systems and multichannel recorders.
-
product
Temperature Transmitter Outdoor, Indoor
T0110
Temperature transmitter with 4-20mA output for two-wire connection is built in a durable watertight case. Output temperature range is user adjustable. Degrees Celsius and Fahrenheit are user selectable. Large dual line LCD is an advantage. Display is possible to switch off.
-
product
Ultrasonic Level Transmitter
USonic
The Drexelbrook family of Ultrasonic technology level products offers an affordable two wire and line powered version for non-contact level measurement of liquids and slurries for level, distance, volume and open channel flow.Measurements of level, distance, volume and open channel flow is easily configured through the menu driven display. The Usonic level transmitter is offered with a two wire 4-20 mA, Hart output signal and is suitable for all Class I Div. 1, Zone 0, I.S. or XP locations. The bench configuration eliminates the need to move process material levels for calibration.
-
product
Temperature Transmitter
H4431
For external Pt1000 temperature probe. Three two-state inputs.
-
product
Micro Power Pressure Transmitter
HR3210
HighReach Measuring & Controlling System Co.,Ltd
Of The HR3210 Series of Micro-Power pressure Transmitters are SPECIFICALLY the Designed to Detect Fluid pressure in The Absence of A Power Source in The Field. Of The Product has Good Stability, High Reliability, High Precision, and Clever Structure for Quick Disassembly and Assembly.
-
product
Cable Locating Kit
CL-300
The NEW CL300 cable locating kit consists of a portable, holstered pipe & cable locator with an industry accepted 33kHz transmitted frequency. Comes standard with 512 Hz detection capability. With an added 512Hz transmitted device or traceable duct rodder the CL300 becomes the perfect tool for empty duct work locating. This instrument is capable of detecting all electrical, telecommunications and wire circuits—whether direct buried cables or those within conduits—using direct connect or close induction methods. This locator equipment features Auto & Manual adjustments for both transmitter power and receiver sensitivity to assist with a variety of locate work and congestion.Applications
-
product
24 TTL Channels, Programmable I/O
TL1
Function module TL1 provides 24 channels of TTL/CMOS transceiver functionality as either inputs or outputs. The transistor-transistor logic (TTL) employs transmitters with multiple emitters in gates having more than one input. TTL offers high switching speed and relative immunity to noisy systems. CMOS sensors provide image sensing technology by converting light waves into signals that are small bursts of current. These waves can be light or other electromagnetic radiation.
-
product
PCI Express 5.0 Transmitter Electrical Performance Validation and Compliance Software
D9050PCIC
Use the PCIe 5.0 Tx compliance software to test, debug and characterize your PCIe Gen5 designs quickly and easily. It automatically configures the oscilloscope for each test and generates an informative HTML report upon test completion. The application compares the results with the specification test limit and includes margin analysis which indicates how closely the device passes or fails each test. With the option InfiniiSim Waveform Transformation Toolset, the software supports integrated de-embedding of the breakout channel of the test fixture.
-
product
T100 Toxic Gas Transmitter
The T100 is a 4-20mA 2-wire transmitter that can measure a wide range of gases. Housed in a rugged, compact metal enclosure, it is designed to be maintenance free and inherently stable.
-
product
Humidity and Temperature Transmitter
T3111Ex-4
Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Transmitter
5081
The Model 5081 family of transmitters can be used to measure pH, ORP, conductivity (using either contacting or toroidal sensors), resistivity, oxygen (ppm and ppb level), free chlorine, total chlorine, and ozone in a variety of process liquids.
-
product
Temperature and Humidity Bar Type Transmitter
T3417
Relative humidity, temperature sensors at 700mm stem. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Humidity and Temperature Transmitter
T3111Ex
Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
10-Watt Broadband Transmitter
Loc3 10W
The 10-Watt broadband transmitter has selectable induction and direct connection frequencies from 98Hz to 200kHz, SD mode (Signal Direction), fault find and true resistance measurement up to 1 Mohm. The two inch by one-inch dot matrix display with LED backlight shows output current, connection type, volts, resistance, frequency, volume, battery condition and high voltage warnings.
-
product
Temperature and Humidity Transmitter
DST1000
Design for airflow velocity and heat transfer rate Applied to HVAC and clean room High-accuracy,wide-measuring range Wide view angle LCD for sharp display Analog or digital output with current ,voltage and RS485 On line calibration-availability
-
product
High-Power Tunable Filter
CB503
The need for tunable filter technology originates from the fact that high power communication systems and IED Jammer transmitters severely limit the use of tactical radio communication systems on the battlefield.This clash within the radio’s spectrum during tactical missions is often de-conflicted using fixed high Q, high power RF bandpass and bandstop filters installed prior to mission. This can limit operational effectiveness due to the potentially large number of fixed filters required within the allocated radio communication channels, which need be transported, stored in the field, and fitted by trained personnel. Many of these fixed filters centred within the octave wide tuning range could be replaced by a single high-Q tunable filter.
-
-
product
Satellite Optical Transmitter
SST-15CW
Hangzhou Softel Optic Co., Ltd.
* Designed for satellite optical system*Wide operating frequency range: 47-2150MHz*Excellent linearity and flatness*Using 1-core single-mode fiber, high return loss*Build-in CWDM, using DFB coaxial small package laser*Output 13/18V, 0/22KHz to LNB working*ALNB mode switch offers the possibility to use either Quattro or QUAD LNB*A distribution of up to 16 optical nodes is possible*Red-LED for power indication*Smaller size and easier installation
-
product
Pneumatic Transmitter
Indicating pneumatic transmitter assists in the coordination of key functional areas within facilities. Transmitting data efficiently and accurately, it ensures operating economies and safety. A good product for process control and monitoring.
-
product
Fiber Extender Kit
L-1SDI-FE-3G-TX/RX
The L-1SDI-FE-3G-TX/RX is a SD/HD/3G-SDI over fiber transmitter and receiver extender kit. This unit provides optical transmission of one SD/HD/3G-SDI signal with embedded audio signal and has reversed RS485 data channel for camera control. L-1SDI-FE-3G-TX/RX kit can be used in HD video conference, as well as HD video monitoring, intelligent transportation system and public security system.
-
product
Force Transmitter
LKVE/i
The PIAB LKVE electronic overload protection system consists of a force transmitter with amplifier and an electronic signal processing unit. The PIAB LKVE force transmitter is attached to a stationary line part. The rope is deflected via a slight angle between the two wheels and the clamping jaw. When loaded, the rope tends to straighten and applies a force which is transmitted to the load cell. The load cell in the PIAB LKVE delivers a signal proportional to the force on the load cell. The signal is amplified and is converted to 4-20mA. This standardized signal (4-20mA) allows distances between the force transmitter and the electronic unit to be 500 m.
-
product
5-Watt Broadband Transmitter
Loc3 5W
The 5-Watt broadband transmitter has selectable induction and direct connection frequencies from 98Hz to 200kHz, SD mode (Signal Direction), fault find and true resistance measurement up to 1 Mohm. The two inch by one-inch dot matrix display with LED backlight shows output current, connection type, volts, resistance, frequency, volume, battery condition and high voltage warnings.
-
product
Optical Modulation Analyzer and High-speed Digitizer Test Solution
M8290A
The M8290A is a flexible solution platform for 400G coherent component and transmitter test. It incorporates a 92 GSa/s modular optical modulation analyzer and a 92 GSa/s 4-channel electrical digitizer. Besides these modules an additional arbitrary waveform generator module up to 92 GSa/s, such as the M8196A, can be added to the same AXIe chassis. This setup results in a compact and flexible coherent test solution that can be used together with additional specialized solution software for Integrated Coherent Receiver (ICR) and Analog Coherent Optical (ACO) module characterization.
-
-
product
Data Logger & Measuring Instruments
Data loggers and measuring instruments of the ALMEMO® series were developed for different measuring tasks and a very wide range of applications. The system consists of a data logger or a measuring device and intelligent connectors, which are used to connect the corresponding sensors. On the instrument side, the versions differ only in the number of measurement inputs. Device types ranging from 1-channel transmitters to measurement data acquisition systems with up to 1000 measurement inputs are available.
-
product
Fiber Transceiver Modules
Optical transceiver (transmitter and receiver) modules convert data signals to and from laser optic light and plug into routers, switches, and fiber host bus adapters (HBA). They provide the transmission of data between transceivers over fiber or optical cables.
-
product
Online Conductivity Controller
LD-LOCC-A10
Online Conductivity ControllerLD-LOCC-A10features 3 points conductivity calibration system, TDS measurement mode, and 4 to 20 mA output signal transmitter. The large and clear back light LCD displays Calibration and setup values, Temperature values, ATC (automatic temperature compensation) values, high and low limit of measurement. This controller measures Conductivity and TDS values in µS/ cm, and mS/ cm units.
