-
Product
VoIP Monitoring and Testing Tool
SIP Tester™
-
StarTrinity SIP tester™ is a VoIP load testing tool which enables you to test and monitor VoIP network, SIP software or hardware. It is able to simulate and passively monitor thousands of simultaneous incoming and outgoing SIP calls with RTP media, analyze call quality and build real time reports.
-
Product
End-to-End Network Monitoring
OSIX
-
Network monitoring with tracing and troubleshooting capabilities to achieve first-class customer experience and to proactively prevent network and service quality degradation. OSIX Monitoring enables Communication Service Providers (CSPs) to detect and resolve network issues or poor performance before end-customers are affected.
-
Product
Seismic Analysis and Monitoring
-
Seismic analysis and monitoring have been designed on the base of the contemporary seismic studies. We can offer you a wide range of tools for geophysical surveys, seismic tomography, automated monitoring of bearing structures (structural health monitoring), seismic monitoring of oil piping systems.
-
Product
ARINC 818 Monitor
-
ARINC 818 Monitor is a rugged display module, powered by High-Performance FPGA to accept various ARINC 818 line rates up to FC 4x and display the converted video data on the monitor of various ICD Specification with very low latency. It supports any progressive video up to Full HD @60fps. These monitors empower pilots to organize and visualize the key information they need.
-
Product
Solace Monitoring With RTView®
-
Centralize your monitoring and alerting across all of your PubSub + Message Brokers
-
Product
Indoor Air Quality (IAQ) Meters, Monitors
-
For handheld, semi-permanent and long-term IAQ measurement
-
Product
Deep Dive Application Monitoring
-
Application performance management (APM) is critical to business success today. Dynatrace automatically sees and analyzes every single user transaction, all the time. All relevant metrics, environment changes, and application deployments are shown in real-time.
-
Product
Transmitter Monitors Carbon Monoxide
CO-R
-
The CO transmitter monitors carbon monoxide (CO) levels and is designed for the continuous monitoring of vehicle exhaust in non-hazardous areas. The CO uses a wide spectrum, long life electrochemical sensor to measure the amount of carbon monoxide in the environment. It is offered with an operating range of 0 to 125 ppm. Both the Room and Duct CO transmitters are offered in a standard NEMA 1 rated ABS Polycarbonate plastic enclosure. An optional NEMA 4X watertight and dust proof enclosure is only available with the CO room transmitter.
-
Product
Concrete Measuring and Monitoring System
IQM-Meter
-
Designed specifically for monitoring and analyzing fresh concrete, the IQM Module is programmed with the required Equivalent Age of the concrete under test. Once this preset maturity number is reached, a visual indicator will flash continuously, providing an effective, automatic indication that the concrete has reached the desired level of maturity.
-
Product
Indoor Air Quality Monitor and Controller
VAT930-CO2/VAT930-CO2-VOC35
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Indoor air quality monitor and controller ( temperature meter. humidity meter . CO2 meter.VOC meter).
-
Product
15" 1024 X 768, VGA/DVI Interface, Open Frame Monitor
IDS-3115
-
15" 1024 x 768 XGA LCD panel with LED backlight for 20% power saving and environmental protection. -20~ 60° C operating temperature support, 5-wires resistive and projected capacitive touchscreen solution, Combo touch interface of RS-232 and USB.
-
Product
MOD MONITOR
TYPE HFX-1
-
The Type HFX-1 Modulation Monitor is an ancillary piece of equipment, which is used with narrow bandwidth, or older oscilloscopes to allow viewing of RF signals and particularly modulated signals as high as 55MHz. The equipment contains an RF signal source and a broadband mixing circuit which converts the high frequency signal to an intermediate frequency within the oscilloscope’s range. The frequency control dial is simply adjusted until the RF signal is viewed on the scope. BNC connectors are mounted on the rear panel to allow interconnect to the scope and RF probe. This product was previously called "oscilloscope frequency extender" and may be used to view other high frequency signals on older or narrow band scopes.
-
-
Product
Joining Monitor
-
We are offering a variety of monitoring equipment for current, voltage, pressure and displacement which is indispensable for quality control of precision micro joining.
-
Product
In-situ Wafer Temperature Monitoring
-
CI Semi's family of noncontact temperature monitors (the NTM line), offers high end pyrometry products for the measurement of wafer temperatures during process. CI Semi’s flag ship of the line, the NTM Delta, incorporates real-time, same point emissivity measurement and compensation making it the ideal solution for in situ monitoring for processes such as RTP, CVD and PVD. The NTM family is sold to leading tool manufacturers.
-
Product
CMM AutoQAL & CMM Continuous Mercury Monitoring Systems
-
Continuous Mercury Monitoring systems, the CMM and CMM AutoQAL, are TÜV and MCERTS certified solutions for continuous mercury monitoring from hot, wet and corrosive gas streams of industrial processes, such as waste incineration, cement production and powerplants. Gasmet offers a full CMM solution package which consists of a system, lifetime service and support, documentation and training, and our expertise.
-
Product
X-Ray Beam Monitors
-
When standard products just aren’t good enough—or the measurement technology does not yet exist—Sydor Technologies develops technology to enable these complex imaging measurements. Just as we’ve developed next-generation streak cameras and x-ray detectors to meet novel, emerging requirements in national laboratories, we’re doing the same with x-ray beam monitors.
-
Product
Ambient Air Quality Monitoring System
AQMS
-
AQMS, the doctor for "Human Health"An Air Quality Monitoring Station (AQMS) is a system that measures metrological parameters such as wind speed, wind direction, rainfall, radiation, temperature, barometric pressure and ambient parameters. The AQMS also integrates a series of ambient analyzers to monitor the concentration of air pollutants (such as SO2, NOx, CO, O3, THC, PM, etc.), continuously. HORIBA also provides mobile monitoring stations that can be used to monitor ambient conditions at multiple sites.
-
Product
Machine Condition Monitoring
-
The system enables precautionary interventions to prevent equipment downtime, increasing equipment lifetimes and reducing maintenance costs. Operational reliability, security, and productivity all benefit.
-
Product
Aerosol Monitor
DUSTTRAK DRX-8533
-
Real-time dust monitoring takes a giant leap forward! Only the DUSTTRAK™ DRX Aerosol Monitor 8533 can simultaneously measure both mass and size fraction - no other monitor can do both. The DUSTTRAK DRX desktop monitor is a battery operated, data-logging, light-scattering laser photometers that gives you real-time aerosol mass readings. It uses a sheath air system that isolates the aerosol in the optics chamber to keep the optics clean for improved reliability and low maintenance.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-33
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 0.1A～150A*Current measurements of feeder
-
Product
LoRaWAN® Wireless Condition Monitoring Starter Kit
WISE-2410SK
-
LoRaWAN® wireless connectivityBuilt-in 3-axis accelerometer and temperature sensorOn-board computing. Directly sends VRMS, ARMS, Peak, Displacement, Kurtosis, Crest factor, Skewness and Standard Deviation values to applicationsSupport battery power supply, no wiring installation neededEasy settings with user friendly interfaces on WISE Studio utilityISO 10816 and ISO 20816 compliantSupport wide temperature -20 ~ 80 °C (Battery-powered)IP66 enclosure design
-
Product
Multi-Channel Monitoring
MULTIPOINT SAMPLER
-
MULTIPOINT SAMPLER enhances the monitoring capabilities of Gasera analysers by increasing the number of sample inlets up to 12. In addition, it performs automated sampling from multiple points.
-
Product
Single Phase Powerline Monitors
-
a Voltage disturbance detector and recorder. This device is designed to be plugged into a 120V or 240V AC line and will monitor this line for voltage disturbances and temperature or Humidity variations.
-
Product
Condition Monitoring
Falcon
-
The ultimate portable vibration data collector and analyzer. With a wide range of optional features available, the FALCON can be configured to perform balancing, run up coast down, frequency analysis and more.
-
Product
Multi-Channel Earth-Loss Monitor
-
The SURETECH Earth-Loss Monitor (ELM) measures the resistance to earth of cable armouring in such a way thatthe user can actually LOCATE the earth loss.
-
Product
Water Quality Monitoring
-
The systematic, ongoing collection and analysis of physical, chemical, and biological data to assess the condition of water bodies.
-
Product
Curved Monitor
-
The introduction of Advantech Curved Monitors creates exciting opportunities for casino slot machines, entertainment kiosk, digital signage, control centers, and medical applications.
-
Product
Free Bandwidth Monitoring & Usage Reporting
NetWorx
-
NetWorx is a simple and free, yet powerful tool that helps you objectively evaluate your bandwidth situation. You can use it to collect bandwidth usage data and measure the speed of your Internet or any other network connection.
-
Product
Water Distribution Monitor
TW-100
-
HORIBA’s TW-100 is a process water quality measurement system designed for drinking water and water distribution plants. The TW-100 monitors turbidity, color, free chlorine and pressure. This chemical free method reduces operating costs as it requires minimal maintenance and improves process control.
