Loop Simulators
-
Product
PXI 8 Channel Switch Simulation Module
40-480-021
-
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
Single-Output Software-Defined GNSS Simulator
BroadSim Solo
-
Designed to address the permanent challenges that engineers face with laboratory capacity and availability, BroadSim Solo was developed to bring advanced GNSS scenario creation to your desk and propel development cycles.
-
Product
Voltage Dip, Interruption& Variation Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
PFS single phase power fail simulator simulates voltage dip, interruption and variation which are caused by power grid and transformer devices due to malfunction or sudden large change of load. It is required to test this kind of phenomena to check whether electronic and electrical device can sustain safety operating condition.
-
Product
PXI RTD Simulator Module, 20 Channel, PT100
40-263-101
-
The 40-263-101 is a 20-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Single or Multi-channel Coherent Signal Simulator
Z2090B
-
The Z2090B-3xx can generate single or multiple coherent outputs to 44GHz with precise phase and amplitude offsets. It is available as a component bundle or as an integrated system.
-
Product
Flux Valve Simulator
FV Sim
-
This flux valve simulator is designed around the synchro format and is employed in our TA-14 DG panel. This simulator is also available now in a portable enclosure for testing the Sperry or Jet Directional gyros.
-
Product
PXI 32 Channel Switch Simulation Module
40-480-221
-
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
6″ (15.25 cm) 1000W Pre-Irradiation Solar Simulator
Model LS1000-6S-009
-
1000W Pre-Irradiation Solar Simulator Kit specifically designed for the pre-irradiation step during in vitro broad spectrum sunscreen testing. Fully compliant with the most current FDA and ISO requirements. The 6″ (15.25 cm) Class A beam can irradiate up to 9 PMMA plates simultaneously.
-
Product
ESD - Simulator
SESD 216
-
The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods
-
Product
Multiphysics Computational Fluid Dynamics (CFD) Simulation & Analysis
STAR-CCM+
-
Siemens Digital Industries Software
STAR-CCM+ is a stand-alone simulation solution for computational fluid dynamics (CFD), computational solid mechanics (CSM), heat transfer, particle dynamics, reacting flow, electrochemistry, electromagnetics, acoustics and rheology. STAR-CCM+ delivers accurate and efficient simulation technologies through a single integrated user interface and automated workflows. This facilitates the analysis and exploration of complex real-world problems.
-
Product
Ethernet Test and Simulation Instruments for Speeds from 10 Mbit/s to 25 Gbit/s
-
Avionics Interface Technologies
AIT’s Ethernet test instruments provide Ethernet test features for 10Mbit, 100Mbit, 1Gbit, and 10Gbit Ethernet networks, for both Optical and Copper media. All instruments are supported by Analyzer and Simulator software applications (GUIs) and additionally software API’s allowing integration into user applications.
-
Product
Basic Rate ISDN and IDSL Network Simulator
Emutel Solo
-
Emutel Solo is a small, portable lightweight battery powered basic rate ISDN and IDSL network simulator. With 2 software switchable S/U interfaces and the choice of either Euro-ISDN, North American or NTT support. Emutel Solo allows you to test and demonstrate all types of BRI equipment on one compact unit. Providing all the standard features but also many others that its compeditors don't include.
-
Product
BRI, PRI and PSTN FXS Simulator
emutel Max
-
emutel Max is a standalone or rackmount unit that comes in five variants giving 8 BRI, 2 PRI and 8 BRI, 2 PRI and 15 BRI, 8 BRI and 14 analogue or 2 PRI, 8BRI and 14 analogue. emutel Max can emulate different country specific networks by adding network personality cards " networks supported include North American, NTT, Euro-ISDN, VN3, ITR6 and BTNR191. Protocol analysis option is also available on emutel Max.
-
-
Product
UV Range Simulators
-
Textron Systems' operational range systems deliver the same rich, high-fidelity environment enjoyed in systems integration laboratories and on flight lines to training ranges for seamless interoperability and maximized training outcomes. Our modular design allows easy configuration of a multispectral system for training and test to support advanced sensor fusion.
-
Product
Simulation & Analysis Solution for Automotive Audio Networks
A2B Analyzer System
-
The A2B Analyzer System is designed specifically for development teams servicing automotive OEMs, Tier 1s, and audio connectivity equipment suppliers. The deterministic nature of the A2B technology makes it particularly well-suited for automotive audio devices (active speakers, microphones) and newer applications such as ANC. The A2B Analyzer System consists of a compact hardware device, an accompanying software development kit (SDK), and network configuration and simulation tools.. The hardware device includes a USB 2.0 interface for PC connectivity for audio data and command/control functions. The small form factor device also features a variety of popular audio and connectivity peripherals.
-
Product
Closed Loop Precise Hall AC/DC Current Sensor
CYHCS-LF
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for accurate measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
ESD Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
State of the art electrostatic discharge simulator available in 18KV. It is the most ergonomic ESD gun without an additional base control unit. It can be operated via battery or mains. The easy to use touch screen, ergonomic design, modular R/C units, remote control software, built-in LED light and temperature and humidity display allows a trouble-free use in all types of test sites.
-
Product
MAGNESIUM ANODE SIMULATOR
CS-1
-
The CS-1 portable Magnesium Anode Simulator is an ideal DC current source that will allow the user to see what the addition of a magnesium anode on their system will do to Pipe to Soil measurements and other C.P. tests.
-
Product
MIL-STD-1553 A / B Test And Simulation VXIbus Module
VXI-1553
-
*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*VISA based VXI Plug & Play driver*Optional twinax front end
-
Product
Simulating Optical Design Components
Wave Optics Module
-
The Wave Optics Module provides dedicated tools for electromagnetic wave propagation in linear and nonlinear optical media for accurate component simulation and optical design optimization. With this module you can model high-frequency electromagnetic wave simulations in either frequency- or time-domain in optical structures. It also adds to your modeling of optical media by supporting inhomogeneous and fully anisotropic materials, and optical media with gains or losses. It is straightforward to simulate optical sensors, metamaterials, optical fibers, bidirectional couplers, plasmonic devices, nonlinear optical processes in photonics, and laser beam propagation.
-
Product
IP / VoIP Analysis & Simulation
-
GL offers high density Ethernet/IP tester variant which includes mTOP™ 1U/2U rack mount enclosures within which PacketExpert™ portable USB units are stacked to provide high density GigE ports form factor solution for testing GigE switches, routers and network conditions.
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Module
PCI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
Single, Dual Or Quad Stream MIL-STD-1553A/BTest And Simulation Modules For PMC
AMCX1553
-
MIL-STD-1553 Test and Simulation modules for PMC with 1, 2 or 4 dual redundant channels plus 8 Discrete I/O’s (on Rear-I/O).
-
Product
Panel-mounted Power Amplifier For Network Simulators
PAV250Bi
-
PAV250Bi is one of the conventional voltage power amplifier model, which is specially designed for R&D of power system simulation.
-
Product
4-20mA Current Loop USB Data Logger
EL-USB-4
-
This data logger measures and stores up to 32,000 current loop readings over flashing red and green LEDs. The data logger features a pair of screw terminals and is supplied complete with a a 4-20mA d.c. measurement range. The user can easily set up the logging rate and start time, and download the stored data by plugging the module straight into a PCs USB port and running the purpose designed software under Windows 2000, XP or Vista
-
Product
Concurrent Alternative RF & GNSS Signal Simulation
SimAltNav Replay
-
Non-GNSS sources of RF (radio frequency) are of interest in GPS-degraded or contested signal environments, with interest focused on LEO (low earth orbit) constellations. These systems offer high receiver signal power (relative to GNSS) and a secure & resilient link to augment GNSS.
-
Product
Simulation Design For Manufacturing
-
Altair offers a unique set of simulation tools to evaluate product feasibility, optimize the manufacturing process, and run virtual try-outs for many traditional, subtractive, and additive manufacturing processes. Users can validate designs early in the manufacturing process with the simplicity and affordability of the simulation software, as well as use optimization technology with specific manufacturing constraints to design better, more efficient products.
-
Product
Solar Simulator
XES Series
-
The recent environmental issues have been drawing more attention over the past few years. So "solar simulators" have come into the public eye much more often. They are mainly used for the evaluation of solar cells as well as for other types of tests where sunlight needs to be recreated.The continuous light of xenon lamp, the most faithful reproduction of sunlight, is applied in our highly accurate solar simulator, which has been widely sold across Japan and neighboring countries."SAN-EI" offer a wide range of solar-related optical technologies and can guarantee to satisfy the needs and request of customers.
-
Product
Friction Flow Loop System
-
Friction Flow Loop System is used for testing the effects of friction reducers by circulating at high rates through different pipe diameters. Friction Loop designs vary based on the application required.
