-
Product
Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 500 units, Max UUT 197 x 114 mm (wxd)
CMK-05
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
-
Product
Test Fixture
OCP NIC 3.0
-
These test fixtures are necessary for testing within the OCP NIC subgroup (found under the OCP Server Work Group). These fixtures will arrive meeting the OCP NIC 3.0 Specification with a characterization of the boards. These fixtures mate with the OCP form factor connector, and will allow an electrical break out of each signaling lane.
-
Product
Automatic Fixture Removal Software
S97007B
-
Automatic Fixture Removal (AFR) software is used to remove the effects of the fixture used to test coaxial connectors, which is required to make accurate measurements on the device
-
Product
Vacuum Fixture Kits
-
*Perfect Sealing *Precise Operation *Stable Construction *Self Closing - Opening Covers
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/HG/KT-ITA-21
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 16,30 kg
-
Product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 500 units, Max UUT 197 x 114 mm (wxd)
CMK-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Audio Panel/Amplifier Test Fixture
TA-200
-
The Model TA-200 test panel was designed to allow Avionics shops the capability to test and troubleshoot both today's new generation audio panels as well as the standard audio panels of the past. The testing of these panels over the years has always proven to be a very time consuming job for most shops because of the limited capabilities of any past test panels.
-
Product
Edge Connector Fixture
EDGE
-
An edge connector fixture can be a low cost alternative to a bed of nails fixture. The most important features of this Edge Connector Tester is its portablility, ease of use, intuitive control functions, and durability in a production environment.
-
Product
Manual Fixture Kit with Changeable Cassette, Max number of probes (2N) 500 units, Max UUT 230 x 175 mm (wxd)
CMK-06
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Test Fixturing Solutions
-
Amfax and MAC Panel have teamed up to provide a unique WIRE-FREE Test fixture technology. We have created an alternative solution to traditional wired ITAs called PECture(TM). The name is a combination of PEC (Printed Electronic Circuit) and fixture.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/15
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,46 kg
-
Product
INTERFACE TEST FIXTURE KITS
GENRAD 2270
-
Test-X GR Series CAM/TRAC® kits offer the same "Z" axis motion as the standard CT Series with the advantage of interface compatibility.Standard features include locking handle assembly, 3/8" FR4 probe plate, and 12 position I/O block interface..
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 335 x 250 mm (wxd)
CMCSK-02-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
MECHANICAL TEST FIXTURE KITS
TX-MT-100 SERES
-
Test-X MT-100 Series mechanical kits are an inexpensive solution for testing smaller printed circuit boards and other devices.The MT-100 Series features a 1/2" thick FR4 probe plate and a 3/8" thick Lexan top plate. Precision alignment is assured through tooling holes in both the probe and top plates. Units are available with a 2-1/2" pan or an upper head assembly
-
Product
Test Fixture, Shielding Effectiveness
EM-2108 | 1.5 GHz – 10 GHz
-
The EM-2108 is a standard test fixture for evaluation of the electromagnetic shielding effectiveness (SE) of planar materials.
-
-
Product
Test Fixture (SMD Components)
16034E
Test Fixture
Perform impedance evaluation on a minimum SMD size of 1.6(L) x 0.8(W) [mm]
-
Product
Fixture Building Software
FixGenius
-
Tests show that FixGenius’ rule-based probe-mapping algorithms reduce pin deflection by up to 25% compared with traditional fixturing packages. FixGenius comes with a powerful Fixture Editor that allows the user to change the probe mapping. If a solution is mathematically possible, FixGenius’ algorithms will find it, and pick the one with least deflection. If the job simply cannot be done with one single fixture, FixGenius will fully automatically split the test into multiple fixtures or into fixture and flying probe test sets, with guaranteed test integrity.
-
Product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
-
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test.
-
Product
In-Circuit Test Fixtures
-
In-circuit testing provides electronic manufacturers a reliable, high fault coverage verification method for the assembly process. Circuit Check ICT fixtures are robust, reliable and designed for easy customization to cover a large range of PCB sizes without impacting turnaround time. We stock a large variety of fixture sizes and actuation methods to meet your test demands. If a stocked sized ICT fixture is not adequate our engineering staff will design a custom solution.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196B
Test Fixture
The 16196B surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results, reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement. Now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
RF-Ready DC Fixture
-
The RF-Ready DC fixture provides space for mounting RF input and output matching circuits. Hence, it is possible to tune up the assembly at a remote test station, such as a network analyzer, to peak performance and then run the life test with DC stimulus. The matching structures also allow incorporation of more complex stabilization structures.
-
Product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 1000 units, Max UUT 580 x 400 mm (wxd)
CMK-04
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
In-Circuit Test Fixture Design Services
-
XJTAG offers consultancy services to design and build production test fixtures that integrate JTAG boundary scan with bed-of-nails testing.
-
Product
HiFIX High Fidelity Tester Access Fixture
-
The HiFIX lineup delivers clean waveform transmission, precision docking, and multi-DUT parallel test, with high reliability.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/7
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,30 kg
-
Product
Universal Test Fixture
Series 48
-
The Series 48 Universal Test Fixture Systems are an effective way to test high mix, low to medium volume products. The Universal Base is designed around the CAMGATE Z axis Test Fixture. The base interfaces with removable, quick change Series 49 Universal Test Insert Kits. Three versions are offered, a blank base whereas the end user can configure the Base and insert kit to their own connector configuration, The 160 point model which uses four (40) pin IDC ribbon cable connectors to interface between the base and the insert kit, and the -I model that incorporates the same 4 block GR2270 style block interface as used on our Series 34 test fixtures. This allows for increased test point count and the use of Industry Standard 2270 style signal, power, and coax blocks. Rear panels can be custom configured to customer specifications, Virginia Panel ITA frames, or GR2270 Interfaces used on Semco’s Standard Product line
-
Product
Automatic Fixture Removal
S96007B
-
Automatic fixture removal (AFR), is the easiest way to remove fixture effects from non-coaxial device measurements.
-
Product
VOC FIXTURE OVER CLAMP ASSEMBLY'S
-
Test-X VOC Series overclamps are used for testing bare or loaded printed circuit boards with open vias and to minimize board flex.The VOC Series overclamp comes with adjustable delrin pressure fingers, anti-rotating hex nuts, hinge and latching assemblies, mounting instructions and hardware.The VOC Series will accomodate fixtures with dress frames or newer style fixtures using full-size top plates.
