Unit Under Test
assures a constituent's interoperability in a system.
See Also: UUT, EUT, System Under Test, Device Under Test
-
Product
Platforms
-
The use of switching systems to route instrumentation and stimulus signals to appropriate test points on a unit under test has a very crucial role to play in most electronics test systems. The sharing of test resources, connection of calibration references, load management, and many other functions are all managed by the switching system, the switching system acts as the interface between the unit under test (UUT) and the test equipment.
-
Product
High Voltage Surge Current Monitors
HVSCM
-
Designed to be used with the Model HVST High Voltage Surge tester. The Surge Current Monitor allows simultaneously surge testing 20 units. The Surge Current Monitor monitors the current going through each unit under test at the time of the surge. If a unit under test breaks down or leaks, the Surge Current Monitor will identify the bad unit by lighting the corresponding LED. The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. In production testing we expect that most of the time the devices will pass. In the event that one should fail, the failed device would be removed and then all the parts would have ot undergo another surge test. Since most devices pass most of the time, simultaneous surge testing can be a real time saver.
-
Product
SIGNAL & POWER ISOLATOR
EE301-ISOL
-
The EE301-ISOLATOR will completely isolate your electronic loads inputs & outputs signals plus ground returns from the main power input UUT (unit under test)... The module allows you to control the electronic load just as you would with any standard control signal. Input / Output & Power signals are fully isolated up to 350 VDC.
-
Product
Camera Testing
FLIR
-
CI Systems' FLIR turn-key test stations carry out all the necessary tests to verify and compare the quality of an infrared/thermal camera. The FLIR test systems are based on CI Systems' NIST traceable blackbody radiation sources, collimators and special thermally controlled targets, designed to provide very accurate IR test patterns. All these combine to project standardized targets with known geometry and intensity to the Unit Under Test(UUT).
-
Product
ITA, G12x, Front Mount, 18 Module
410104474
ITA
The G12x ITA can be used with all G12x Receivers. The ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC Enclosure or customize your own fixture to be attached to the ITA. These are front mounted for ease of installation. A wide range of ITA modules are available separately for user configuration.
-
Product
SWB-2812, 16x9, 1 A, Reed Matrix Module for SwitchBlock
781421-12
Matrix Switch Module
16x9, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2812 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Digital Test Instrumentation
Di-Series™
Test Instrument
The Di-Series tests all levels of integration from board level (SRA/SRU) to box level (WRA/LRU) units under test (UUTs), while maintaining full compatibility with previous generations of Teradyne instrumentation and systems. Excellent usability and reliability reduce programming and support effort, as well as straightforward upgrades of existing test program sets (TPS).
-
Product
DIELECTRIC and CONTINUITY TESTERS ( HI-POTS )
AV-25V-GC1-05
-
This tester is designed for testing equipment wiht a line cord which can be plugged directly to the tester. The continuity test is to determine whether the ground wire of the line-cord is well connected to the metal frame of the unit under test.
-
Product
Edge Press Technology Bed of Nails Testers
Prober Edge Press Family
-
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
Product
SpaceWire Physical Layer Tester
141
-
The SpaceWire Physical Layer Tester (SPLT) is a tool designed to test, validate and verify a SpaceWire system across all levels of the SpaceWire standard. Two SpaceWire ports employ a special LVDS interface which allows the transmitted signals to be deliberately and measurably manipulated to test the capability of a unit under test to receive signals of varying quality.
-
Product
Digital and Analog Test Sets
-
Our analog and digital automated test system experience covers a wide variety of applicationsfrom multiple path resistance, capacitance, and inductance testing using various Interface Test Adapters (ITA)to inter-connect multiple customer units under test (UUT). Other systems have included: equipment to monitor and record telemetry, digital data streams, and systems that evaluate packet data using a variety of VME, VXI, PXI, and LXI equipment.
-
Product
Press Down Rods Bed of Nails Testers
Prober Press Rods Family
-
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
Product
Interface Panel for SLSC
THROUGHPOINT™
Interface
Bloomy's ThroughPoint™ Interface Panel provides a simple, yet highly-flexible connection between the unit under test and resources in a National Instruments Switch/Load/Signal Conditioning (SLSC)-based test system.
-
Product
SWB-2813, 4x21, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781420-13
Matrix Switch Module
4x21, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2813 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Day Camera Testing
-
CI Systems' CCD test stations are used to carry out all the necessary tests to verify and compare the quality of a CCD based camera. These stations are based on CI Systems' reflective collimators, Visible Radiation Sources, special targets and integrated software, to project standard patterns with known geometry and intensity to the Unit Under Test. As a result, these stations are turnkey solutions for the CCD camera testing needs.
-
Product
SWB-2812, 16x9, 1 A, Reed Matrix Module for SwitchBlock
781420-12
Matrix Switch Module
16x9, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2812 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
Shock Control
-
Shock testing simulates an extreme event that a unit under test is exposed to during handling, shipment, explosive event and/or daily use (e.g. dropping an object). The profile for this type of testing is defined by the shape of the time domain waveform together with its amplitude and duration. The m+p VibControl vibration control system offers full functionality for classical shock and shock response spectrum testing as well as for tests using external pulses or the capture of transient signals.
-
Product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781421-17
Relay Matrix Module
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
LXI Low-Frequency Matrices
-
Our LXI low-frequency matrices provide complete flexibility for connecting test equipment and the unit under test (UUT)together and are compliant with LXI Standard 1.4
-
Product
SIMRC - RS232 to I2C Converter PCB
1080-001
-
Pickering Interfaces Series 1000 SIM Reed Relay Cards offer a choice of switching configurations using low cost industry standard SIM connectors. They are ideal for placing switching systems in fixtures close to the unit under test.
-
Product
Temperature & Humidity Testing
-
DATASYST Engineering & Testing Services, Inc.
DATASYST can simulate both high and low temperature with humidity conditions. Cycle rates are dependent upon individual chamber capabilities and whether or not a unit under test is powered or not. DATASYST provides humidity testing for a range of industry specifications and can work with you on your customized testing requirements.
-
Product
JTAG 3rd Party Controller Support
-
Corelis offers support for a variety of devices and instruments from third-parties in an effort to provide existing test platforms comprehensive JTAG test execution with Corelis ScanExpress software products. Supported instruments include National Instruments PXI-655x HSDIO and Teradyne Di-Series modules. Corelis also provides support for JTAG testing with FTDI FT2232 ICs embedded on a unit under test (UUT).
-
Product
SWB-2815, 4x86, 0.3 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-15
Reed Relay
4x86, 0.3 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2815 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
SWB-2816, 8x46, 0.3 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-16
Reed Relay
8x46, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2816 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, … individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Torque Measuring and Monitoring System
WISER 4000
-
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
-
Product
Display Color Analyzer
Model 7123
Analyzer
Luminance and chromaticity measurement of Color Display0.005 cd/m2low luminance measurement (A712301)Wide luminance range: 0.0001 to 25,000 cd/m2 (A712301) 0.01 to 200,000 cd/m2 (A712302)High accuracy measurementMaximum 9 display modes: xyY, TΔuvY, u’ v’ Y, RGB, XYZ, Contrast, ProgramAble to control Video Pattern Generator and UUT (Unit Under Test)Built-in contrast measurement function to calculate the contrast ratio directlyEquipped with programmable test items that can complete the planned tests with one single buttonSupport USB flash disk that can copy the test procedures to other station for useJudgment function embedded to judge the test result automatically with one single buttonCalibration period setting and reminding functionMemory for storing 100 channels of standard color data and calibration dataBuilt-in flat display calibration data LCD-D65 & LED-D65* to be applied for chromaticity measurement instantlyOptional display white balance alignment system can be used to integrate all optical test stations to one single station
-
Product
SWB-2814, 8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781421-14
Matrix Switch Module
8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2814 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Automated Bench Test Equipment
-
The Automated Bench Test Equipment (BTE) provides a combination of automatically sequenced and manually selected electrical or electro-mechcanical stimulation to an electronic or electro-mechanical unit under test. The system simulates the normal and threshold operational ranges of each of the inputs and communication channels of the unit under test.
-
Product
SWB-2810, 4x43, 1 A, No Row Access, Reed Relay Matrix Module for SwitchBlock
781421-10
Reed Relay
4x43, 1 A, No Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
