Signal Proccessing
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
Product
Signal Level Meters
-
GAOTek offers a wide range of high performance and inexpensive TV and CATV signal level strength meters. TV signal strength meters and testers are required when installing or maintaining analog TV and digital TV systems and closed CCTV systems. The devices can effectively and accurately measure the analog channels and digital channels signal strength and are the preferred choice of TV installation technicians.
-
Product
CATV & RF Signal Products
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber is a worldwide leading provider for fiber optic equipment, fiber optic test instruments and other data network & telecom products of communications, commercial, and consumer markets. The Company offers test and measurement systems and services to telecommunications service providers, cable operators, and network equipment manufacturers. In addition, the Company offers components, modules, and subsystems for Wireless, Telecommunication, Datacom, Power, Cable TV measurement instruments and utilities applications.
-
Product
GPS / GNSS Antenna Signal Splitters
-
INSTOCK Wireless Components, Inc
INSTOCK Wireless GPS Signal Splitters are available in 2-way thru 48-way configurations spanning 1-2 GHz with unpeered performance in GPS (L1-L5), GNSS, Galileo, GLONASS, BeiDou, and IRNSS antenna splitting applications. The 200 ohm internal load on the DC-blocked port(s) prevents receivers from incorrectly sensing an antenna fault when there is no current draw. Type N, SMA, TNC, BNC, and QMA connector configurations INSTOCK.
-
Product
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp/Solder
610110125
Signal Contact (Receiver)
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp/Solder.p/n 610110125 TriPaddle Receiver 50µ" AU platingp/n 610110101 TriPaddle Receiver 30µ" AU platingThis contact primarily used in CASS applications.
-
Product
Signal, Patchcord, ITA, 36", TriPaddle, 24 AWG White Teflon, Single Ended (3 Amps)
7-103924000-036
Signal Patchcord
Signal, Patchcord, ITA, 36", TriPaddle, 24 AWG White Teflon, Single Ended (3 Amps).
-
Product
Signal Conditioning
-
Mantracourt’s analogue output strain gauge signal conditioning modules offers a flexible solution for any analogue requirement.
-
Product
Mixed Signal, Multi-Functional Test Module
PXIe-ScanIO-112
Test Module
The PXIe-ScanIO-112 delivers a powerful combination of digital, analog, and AC-coupled testing in a single PXIe module. With 104 boundary-scan controllable digital I/O channels and 8 analog I/O channels ranging from –15V to +15V, engineers gain the flexibility to test a wide variety of board-level designs. The module supports IEEE-1149.6 AC-coupled interconnect testing, configurable single-ended and differential pin operation, and integrates seamlessly with the Corelis ScanExpress™ suite.
-
Product
DVB-s2 Satellite Signal Level Meter
AI TURBO S2
-
The AI Turbo S2's extreme ruggedness, husky battery, ease of use, and versatility, make this the ideal meter for professional satellite technicians.
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784776-01
Signal Module
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
Product
Signalling Testers
-
Anritsu's strong and flexible Signalling Testers are a key part of Anritsu's total wireless test and measurement solution, utilizing technology developed through our global leadership in this market.
-
Product
Optical Signal Conditioning Products
-
The single-mode fiber N7761A, N7762A and N7764A provide 1, 2 or 4 attenuation channels in a compact remote-controlled instrument. These attenuators provide very fast adjustment and have built-in output power monitoring for accurate power setting and control, as needed for receiver sensitivity testing or in system simulations.
-
Product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781263-01
Signal Module
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
Product
1465 Series Signal Generator (100kHz – 67GHz)
1465
-
1465 series microwave signal generators, with the frequency range of 100kHz – 67GHz, is provided with high purity spectrum and high output power. It can meet the high-end requirements of electromagnetic signal tests. S1465 series are mainly used in the radar performance evaluation, high-performance receiver test and components parameter test etc., and applicable to aviation, aerospace, radar, communication and navigation equipment etc.
-
Product
DYNAMIC SIGNAL ANALYZERS
900 Series
-
The new SignalCalc 900 Series software makes the process of defining a test, making measurements, analyzing data and generating high-quality reports easier than ever before. All setup, project, test article, and customer information is saved along with measurement data in a database. Easily search for data from different test runs and test types for analysis and report generation.
-
Product
Signal, Contact, ITA, TriPaddle, 7 Amp, 26-28 AWG
610110169
Signal Contact (ITA)
Primary mating contact 610110167. (May mate with other Receiver contacts, as well.)Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
Product
Cloud-Based RF Signal Analysis Software
Cloud4Testing
-
Our next-generation software as a service (SaaS) platform is an ideal choice for your test and measurement needs. With the R&S®Cloud4Testing, you can enjoy a quick and easy access to Rohde & Schwarz testing essentials without having to make a big investment. Simply measure, analyze and process your individual RF data, on demand and on the go.
-
Product
Large Photo Signal Generator
DDS9m
-
170MHz 4-Channel Signal Generator. The DDS9m generates four independent, phase synchronous sine wave output signals and is programmable in 0.1Hz steps from 0.1Hz to 171MHz. Programming is via an RS232 serial interface. Phase is 14-bit programmable and amplitude is 10-bit programmable. The DDS9m is accurate to 1.5ppm when using the on board TCXO timebase or you can use an external timebase. It requires 3.3 VDC power. SOF8_409 windows software is available as an extra cost accessory.
-
Product
Dynamic Signal Analyzer & Data Acquistion
Electroacoustics Toolbox
-
Electroacoustics Toolbox is a modularized, multi-channel dynamic signal analyzer and data acquisition platform for Mac. It brings powerful new tools to the Macintosh platform for multi-channel, audio-band data acquisition and real-time analysis of electrical, acoustical, and electroacoustic signals and systems. It enables precise measurements of acoustic quantities, such as equivalent and time-weighted sound levels, as well as acoustic and electroacoustic systems, such as listening rooms and loudspeakers.
-
Product
Signal Processor Board
MS 1532
-
- Frequency coverage from 5 kHz to 30 MHz in 1-Hz steps- High dynamic range: +30 dBm 3rd-order intercept typical- Digital filtering provides 58 IFBWs from 56 Hz to 8.0 kHz with exceptional shape factors- AM, Synchronous AM, FM, CW, USB, LSB & ISB detection modes standard- Tunable notch filter- Fast, flexible scanning with 100 memory channels- Large readable LED displays & user-friendly controls- Noise blanking & pass band tuning- Internal switchable preamplifier & attenuator- Operator-selectable RS-232, RS-485, or- RS-422 remote control- Viretx 5 FPGA based design (Two virtex for image processing)- LPC2468 ARM 7 Processor based design- MIL1553B and RS485 Interface- Two High speed 14 bit ADC (125MSPS) for I & Q Sampling- Direct sampling 2-30MHz- Audio CODEC- Conduction Cooled Board
-
Product
Digital Signal Processors
-
Powerful Field Programmable Gate Array (FPGA) based Digital Signal Processors (DSP) with large memory, fast PCIe and optical data interfaces (ODI)
-
Product
FPGA Signal Processor
372
-
The Model 372 is designed around the Texas Instruments ADS42LB69 16-bit ADC and the Analog Devices AD9788 DAC. The 250 MHz sample clock is supplied by either the on-board frequency synthesizer or an external source. The frequency synthesizer can be phase locked to the local 10 MHz TCXO or an external reference can be used to achieve system-wide phase coherence.
-
Product
16-Channel Analog Multiplexer & Signal Conditioning Card
AIM-16
-
Model AIM-16 accepts, pre-amplifies, and multiplexes analog signals for application to an analog-to-digital converter installed in a host computer. Each AIM-16 concentrates 16 differential analog input channels into one single-ended analog output channel. Up to eight AIM-16s can be cascaded providing total capacity for 128 inputs to an "8-input A/D Converter."
-
-
Product
Signal Path Analyzers
HL2200 Series
-
HYPERLABS HL2200 Series Signal Path Analyzers™ provide high-performance test and measurement capabilities for a fraction of the cost of traditional benchtop systems. These differential, multi-channel instruments are ideal for interconnect characterization, debugging cable assemblies, coupon testing, controlled impedance analysis, and other applications requiring a fast rise time.
-
Product
Automotive And Signalling Goniophotometers
-
Photometric Solutions International Pty Ltd
PSI offers a diverse range of Automotive and Signalling Goniophotometers. These operate in the CIE A/alpha coordinate system, and are used to measure and evaluate devices such as:
-
-
Product
PXI Breadboard Module, 1Slot, Dual 20-Pin GMCT
40-220A-811
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
Signal Generator High-Frequency GSM AXIe
-
The hardware-software complex "High-frequency GSM signal generator AXIe" is designed to generate harmonic sinusoidal signals with analog modulation (AM, FM, PM, IM) or without modulation in the frequency range from DC to 10 GHz.
-
Product
Programmable Video Signal Generator
VG-873
-
Complete Solution for Development of 4K x 2K & 3D core based technology, ideal for your lab or production line
-
Product
RF Signal Generator With 1.5 And 3GHz Models
TGR205x Series
-
150kHz to 3GHz (TGR2053) and 150kHz to 1.5GHz (TGR2051) frequency rangeHigh signal purity, phase noise <-117dBc/Hz (typical) at 1GHz output and 10kHz offsetAmplitude range of -127dBm to +13dBm0.1dBm amplitude setting resolutionInternal or external analogue modulations (AM, FM, PM)Amplitude can be set in dBm, dBμV or in linear Volts.Internal or external digital modulations - ASK, OOK, FSK, 3FSK, 4FSK, GFSK, MSK, GMSK, HMSK & PSK with U01 optionModulation SynchronisationFast amplitude and/or frequency sweeps with comprehensive triggering5ms sweep settling time1ppm frequency accuracy, <1ppm drift in first yearModulation waveform output on the rear panelInternal waveforms include: Sine, Square, Ramp, Triangle, PRBS (various lengths) and user-defined patternSimple operation with the colour touch screenProgrammable via USB, LAN (LXI) and GPIB (optional), SCPI compatibleCompatible with previous Aim-TTi RF generators
