DC Electronic Loads
The current that results from resistive elements of the load on an output.
-
Product
AC Load Bank (Resistive)
K-1000 Resisitive
-
Kongter Test & Measurement Co., Limited
The kW of a resistive load bank is “real” power in electrical terms. When a resistive AC load bank is used to test an engine generator set the engine will produce its full horsepower rating, dissipate engine exhaust gases, and produce thermal energy into the engine cooling system. The resistive load bank in fact, will completely test the engine and its various systems.
-
-
Product
Electronic Resistance Store
MEMS2-4L
-
The mezzanine serves as an electronic store of resistance to direct current, the value of which is set by software, through two isolated channels.
-
Product
DC Power Supply
◎PW-4063R
-
*Use Toroidal Transformer. Low EMI & High EMS.*Triple output, 0-32V/0-6A X2 and 5V/3A .Max. 400Watts*Tracking operation. Max. output 64V/6A on tracking series or 32V/12A on tracking parallel.*4 display, Green LED shows Voltage and Red LRD shows Current. Easy to read.*Compact design. G.W. 9Kgs only. Easy to handle.*The resolution of PW-4063R as high as 0.01v and 0.001A.*Provide 4Pcs 10turns micro adjust VR for Voltage and Current adjustment. Easy to operate.*Very low Ripple & Noise, less than 0.4mVrms. Very suit for precise measurement.
-
Product
Electronic Magnet Pole Finder
MPF-120
-
The hand-held electronic magnetic pole finder / magnetic pole detector that instantly provides a positive reading of N or S polarity. Simple, push-button operation. Just point and read RED indicates NORTH, GREEN indicates SOUTH.
-
Product
DC Insulation Monitor
ISM-200
-
Kongter Test & Measurement Co., Limited
ISM-200 Insulation monitoring system is a high accurate and secure online monitoring equipment for DC system insulation. It is designed for the measurement of different types of ground fault, insulation decreasing, AC signal interruption, DC signal interruption and so on.
-
-
Product
DC Power Supply
PW-7033
-
*Portable type, small size design*Overload protection*3 sets output: 0~32V/0~3A x 2 + 5V/3A*Parallel: 0~64V/0~3A or + 32V ~ -32V/0~3A*Series: 0~32V/0~6A*3 digits, 4 sets LED display, Green is display for voltage, Red is display for current, easy to read, no mistakes.
-
Product
OEM, Embedded, and Custom Electronics
-
Picosecond timingPrecision analog and mixed signal processingDigital delay and pulse generationHigh speed photonics and fiberoptic timing distributionAerospace instrumentation and simulation
-
Product
Motive Power Load Banks
-
The only way to be certain that your stationary batteries will perform to specification is to test the batteries’ capacity with a DC load bank / portable battery discharge tester.
-
Product
LOADED BOARD TEST PROBES
SERIES-70
-
ElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35mA test current70 18 mOhms mean73 60 mOhms mean74 40 mOhms meanMaterials and FinishesPLUNGER: Heat treated beryllium copperor steel hardened to 55-60RC70 24Kt gold plated over nickel73 24Kt gold plated over nickel74 Rhodium plated over nickelBARREL: Nickel silver70 24Kt gold plated ID and OD over nickel73 No Finish74 24Kt gold plated ID and OD over nickel
-
Product
Regenerative AC load function
61800 Series Optional Function
-
The regenerative AC load function consists of various modes such as CC Rectified mode, CP Rectified mode, CR mode, CC Phase lead/lag mode and CP Phase lead/ lag mode. The Rectified Mode is capable of simulating non-linear rectified loads with characteristics similar to Chroma 63800 series AC load where the voltage and current operate at the 1st and 3rd quadrant. The Rectified Mode supports both CC and CP functions with current, power and CF as parameter settings.
-
Product
Spring Loaded Connector 20A
Swift-Dock-Ultra-Power®
-
For applications with current loads up to 20 amps. With a pitch of 10mm, this is our largest and most rugged or our Swift-Dock range of spring loaded interface assemblies. Ideal for... Rapid battery charging, Rugged environments, Data-loggers, Telecoms devices.
-
Product
DC Current Shunts
-
DC current shunts / standards are true 4-terminal devices that precisely measure DC currents from 10 A to 10,000 A. They use special alloys in the resistive elements which are supported on an insulating base for mechanical stability. The 9230A includes special features to reduce the effects of power dissipation and associated self heating errors. These shunts are designed to operate in air at full rated current. These are the best performing, and most widely used, DC metrology shunts in the world.
-
-
-
Product
Load Cell Measurement
-
Designed specifically as a single-board solution for material testing system (MTS) applications, the PCI-9524 combines a high 24-bit resolution with 1/200,000 count accuracy to provide the most precise load cell measurement PCI board available in the market today.
-
Product
LED Load Simulator
63110A/ 63113A/63115A
Simulator
As shown on the V-I curve in figure 1, the LED has a forward voltage VF and a operating resistance (Rd). When using a resistor as loading, the V-I curve of the resistor is not able to simulate the V-I curve of the LED as shown in blue on figure 1. This may cause the LED driver to not start up due to the difference in V-I characteristic between the resistors and the LEDs. When using Electronic Loads, the CR and CV mode settings are set for when the LED is under stable operation and therefore, is unable to simulate turn on or PWM brightness control characteristics. This may cause the LED driver to function improperly or trigger it’s protection circuits. These testing requirements can be achieved when using a LEDs as a load; however, issues regarding the LED aging as well as different LED drivers may require different types of LEDs or a number of LEDs. This makes it inconvenient for mass production testing.
-
Product
Autoranging System DC Power Supply, 80 V, 510 A, 15000 W, 208 VAC
N8931A
DC Power Supply
The Keysight N8900 Series provides 5 kW, 10 kW, and 15 kW autoranging, single-output programmable DC power for ATE applications that require just the right amount of performance at just the right price. The N8900 Series power supplies' autoranging output characteristic enables unprecedented flexibility by offering a wide range of voltage and current combinations at full power. Power supplies with "rectangular," or traditional, output characteristics provide full power at only one voltage and current combination. Just one N8900 does the job of multiple power supplies. It's like having many power supplies in one!
-
Product
Standard Shackle Load Cell
SS-3.0
-
The DLM Standard Shackle Load Cell is a high strength marine grade cable connected Load Cell. Manufactured from industry leading Crosby or GN Shackles along with a stainless steel load pin.
-
Product
Electronics
-
Weidmüller Interface GmbH & Co. KG
Electronics lie at the heart of your automation technology. We give you solutions with intelligence.
-
Product
DC Bench Power
XPF Series
-
AMETEK Programmable Power, Inc.
The Sorensen XPF is a new type of bench power supply designed to meet the need for flexibility in the choice of voltage and current. Typically, the maximum voltage and maximum current are not required simultaneously. The PowerFlexTM design enables higher currents to be generated at lower voltages within an overall power limit envelope. This is achieved by using the latest switch-mode technology.
-
Product
DC TO 40 GHz
MDHC Series
-
Smiths Interconnect's spring loaded High Frequency Micro-D Coax Connectors MDHC offer low VSWR of 1.5:1 (typical) up to 40GHz (max mated pair), maximum overall diameter of 0.125" fitted into low-profile micro-D housing, constant 50 Ohm airline impedance.
-
Product
48V / 300 Amp Load
BD18-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and isextremely cost effective.
-
Product
PowerSync Programmable Load
-
Lower cost solutions for versatile 802.3at and 802.3bt Powered Device Emulation to support PSE system test and analysis
-
Product
Load Banks
EL08 Series
-
*Rectifier Test 8kW*All of our Load Banks are continuously rated for Power and Current.
-
Product
Electronic AC Potential Standard
PMT25010
-
Power Measurement Technologies Inc.
Provides the electronic equivalent of a standard potential transformer as typically required for instrumentation potential transformer accuracy testing.
-
Product
SQUID Electronics
SQUIDViewer Software
-
Our LabView® based control software for Windows® is the most convenient way to adjust and supervise your system.
-
Product
Electronic DC Load, 500V, 16A, 400W
LDH400 Series
-
Versatile solution for direct testing of dc power sources and PFCsConstant current, resistance, conductance and power modesWide voltage and current range, 10 to 500V and 0 to 16A400 watts continuous dissipation at 28°C (360W at 40°C)High resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminalsLoad inputs rated to CAT II (300V)Full bus control via USB, RS232 and LXI compliant LAN interfacesGPIB Option
-
Product
AC Load Banks
XL300-400 Series
-
Mosebach Manufacturing Company
The XL300-400 Series of Load Banks offer 300 kW or 400 kW in various voltages in a compact, lightweight enclosure.
