-
Product
Digital Strain Gauge Sensor
ZET 7111
-
The ZET 7111 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or separate external tension gauges connected using half-bridge or bridge scheme.
-
Product
Temperature Transmitter
T4211
-
Transducer is designed for temperature measurement at C or F by means of an externaltemperature probe with Pt1000 sensor. Measured values are displayed on LCD display. It ispossible to switch OFF the LCD at all.
-
Product
Digital Display Auto Torsion Testing Machine
NJS Series
-
Jinan Testing Equipment IE Corporation
NJS Series Digital Display Auto Torsion tester is designed and built for torsion test on metal & non-metallic materials, as well as parts & components. NJS is loaded through the rotation of the active cartridge driven by the AC servo motor and cyclonical pinwheel reducer motor. The torque and torsion angle are measured respectively by the high-precision torque transducer and photoelectric encoder. The digital torsion testing machine is an essential instrument to inspect torsion properties of materials for mechanical laboratories of aviation industry, construction industry, scientific research department, universities and industrial enterprises.
-
Product
Meter Test System
MTS-122
-
Kongter Test & Measurement Co., Limited
This rugged Meter Test System is composed of high accurate (class 0.05% or 0.1%) standard reference meter and power source (up to 36A). This system is particularly designed with modular structure for calibration and test of analog meter, digital meter, RTU, electrical transducer, energy meter and so on. It is operated under high functionality with user friendly interface.
-
Product
Open Loop Hall Effect Current Sensors Transducers With Rectangle Windows
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a highgalvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current, DC pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
-
Product
NI-9426, 24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module
780030-02
-
24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module - The NI‑9426 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels.
-
Product
Ultrasonic Flowmeter
F8
-
Gentos Measurement & Control Co.
The F8 Flow meters is a state-of-the-art universal transit-time flow meter for heavy industrial applications. Sophisticated electronics incorporating the latest developments in digital signal processing coupled with powerful ultrasonic transducers deliver highly accurate flow measurement for liquids in full pipes.
-
Product
Transducer Test System
TTS-030
-
For the generation of unique bond links the use of high-quality components is an essential precondition. Despite all care in the production of ultrasonic transducers again and again unexpected effects occur, which only manifest themselves in the use of those transducers and which also have the reason in the transducer itself.
-
Product
Hydrophone
RESON TC 4034
-
The TC4034 broad band spherical hydrophone provides uniform omni-directional characteristics over a wide frequency range of 1Hz to 480kHz.The overall receiving characteristics makes the TC4034 an ideal transducer for making absolute underwater sound measurements up to 480kHz. The wide frequency range also makes the TC4034 perfect for calibration purposes, particularly in higher frequencies.
-
Product
Radiation Resistant Resolver
-
Computer Conversions Corporation
Computer Conversions GT Transducers are brushless, Electromagnetic, Rotary Sensors used to provide Precise Absolute or Incremental Position, and Velocity feedback in harsh environments. All Computer Conversions Transducers are continuous rotation, bidirectional, and electronically passive devices (no electronic components to degrade or fail), that require zero maintenance, and may be installed in virtually inaccessible locations.
-
Product
Audio MEMS Sensors
-
An audio MEMS sensor is an electro-acoustic transducer housing a sensor (MEMS) and an application-specific integrated circuit (ASIC) in a single package.
-
Product
Interface Converter
ZET 7070
-
Basic delivery scope with digital transducers for laboratory use includes the following: interface converter ZET 7070, power supply module 220V→ +24V, measuring line connector ZET 7001 (these components are mounted on a din-rail 300 mm); cable USB 2.0 A→B – length 1,8 m; terminal resistance 120 Ohm (for industrial use — steel plug); CD with ZETLAB SENSOR software, enabling connection of up to 60 digital sensors; set of operational documentation.
-
Product
Probes For Non-Contact Ultrasonic Testing
SONOSCAN CFC / CF
-
Due to the strong damping properties of air, low frequencies in the kHz range are used in air-coupled ultrasonic testing. It is therefore all the more important that the ultrasonic transducers offer a particularly high sensitivity in order to ensure high penetration and improved resolution. We achieve this, among other things, by installing preamplifiers in the receiver probe as well as by using our own Piezocomposite Technology, which enables a flexible use of the matching materials in our CFC and CF probes.
-
Product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
-
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
Product
Thickness Gauges
UMX-2
-
UMX-2 underwater material and coating thickness gauge, designed for offshore inspections, and rated to a depth of 1000 feet (300 meters). The UMX-2 is very versatile, offering both Dual & Single element transducers. Equipped with multiple measurement mode options, the UMX-2 will meet all your application requirements. Onboard 5,000 point data logger, all UMX-2 settings stored for each measurement, along with an actual A-Scan waveform.
-
Product
Ultrasonic NDT Transducers
-
United Western Technologies Corp
The Quick Change Transducer (QCT) series of transducers that makes changing wedge angle and transducer frequency rapid and easy, saving both time and money. The QCT connects straight into the wedges allowing for many combinations all within one kit. All QC Transducers are fitted with top mounted microdot connectors allowing for seamless transition from one transducer to the next. The stainless steel transducer housing will resist even the harshest working conditions. The emphasis of the QCT is general purpose with a balance of power and resolution, a High resolution version is available upon request.The Quick Change Wedge (QCW) is simple to setup and operate, utilizing incorporated noise dampening material on the wedge. Offered in steel, aluminum and titanium refracted angle. Custom contours, radii and wear pins available upon request.The QCT and QCW series are extremely versatile and can be used in many different applications and in a wide variety of industries and environments.
-
Product
sbRIO-9375, Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781212-01
-
Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The sbRIO‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The sbRIO‑9375 offers isolation between the input and output banks from channel‑to‑earth ground. Non-enclosed modules are designed for OEM applications.
-
Product
Pressure/Vacuum Calibrators
-
Compact, completely self-contained unit designed for calibrating and testing pressure gauges, transducers, pressure switches, and other pressure-sensitive instruments up to 2,000 psi with an accuracy of ±0.25% of full scale.
-
Product
Closed Loop Hall AC/DC Current Sensor
CYHCS-D8
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current in the carrying conductor.
-
Product
Bolt Extensometers for Proof Load Testing
Model 3565
-
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Pressure-Force Cables And Connectors
-
Connectors used for pressure and force sensors. Includes cable assemblies for pressure transducers and load cells, DIN connectors, twist lock connectors, push on connectors, and dynamic sensor cables.
-
Product
Ultrasonic Transducer
-
F&K Physiktechnik offers ultrasonic transducers "Made in Germany" for all kinds of bond applications. The complete range includes fine wire wedge transducers, fine wire ball transducers as well as heavy wire transducers.
-
Product
Acoustic Testing
-
Our acoustic testing experience includes acoustic qualification and evaluating sound pressure levels. We utilize microphones, pressure trans-ducers, and an acoustic intensity meter to record acoustic measurements.
-
Product
Software
DPM-3
-
Was developed to read and edit Plug and Play Smart Sensors that are compliant to the IEEE 1451.4 Standard. TEDS, or transducer Electronic Data Sheet, is a set of electronic data in a standardized format defined within the IEEE 1451.4 standard. This data specifies what type of sensor is present, describes its interface, and gives technical information such as sensitivity, bridge type , excitation, etc. This information is stored in an EEPROM chip attached to the sensor. By having this chip, the sensor can identify and describe itself to the network and or Smart Load Cell Meter (DPM-3), thereby easing automatic system configuration.
-
Product
High Temperature Diametral Extensometers (1000 C)
Model 3580
-
Jinan Testing Equipment IE Corporation
This model is for diametral strain measurement with furnace and induction heating systems. Quartz rods and water-cooling allow the unit to be used for high temperature testing of metals, ceramics and composites. With induction heating, this model often can be used without water-cooling. When used in furnaces, the extensometer is often mounted directly to the furnace side cut-out. Optional load frame mounting brackets are available for supporting the extensometer in cases where furnace mounting is not possible. These optional mounts are used with induction heating or furnace systems. The Model 3580 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
ChenYang Voltage Sensors/Transducers
-
ChenYang Technologies GmbH & Co. KG
DC voltage sensor/transducer works according to Linear PhotoelectricalIsolation and is designed for applications to measurement and monitoring of DC voltage. Theoutput signal (DC voltage or current) of this transducer is proportional to the input DC voltage.They are suitable for measurements and long time monitoring of DC voltages and can applied topower supply management, DC motor drivers, battery chargers and systems etc.
-
Product
Triaxial Testing Machines
-
Triaxial testing machine for position-controlled triaxial tests with test cells 10-3150 ... Stand model in two-column design with electronic force transducer, flanged to the testing machine crosshead and adjustable electronic position transducer 50 mm. The machine is driven by a stepper motor with central spindle and pressure plate below.
-
Product
Long Gauge Length Axial Extensometers
Model 3542L
-
Jinan Testing Equipment IE Corporation
The dual flexure design makes the 3542L very rugged and insensitive to vibrations. These extensometers are designed for testing a wide range of materials including metals, plastics, composites and ceramics. Epsilon’s Model 3543 is recommended for applications requiring long gauge lengths and larger measuring ranges.The Model 3542L comes standard with Epsilon’s quick attach kit, making it easy to mount the extensometer on the test specimen. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The 3542L extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
TE-Metrology
-
HIGHVOLT Prüftechnik Dresden GmbH
The TE measurement complements the high voltage test and is part of the routine and type testing of numerous electrical devices. It is one of the most important non-destructive methods for detecting faults in electrical installations. The breakdown of an insulating material usually occurs at an internal weak point, which usually already shows a partial discharge activity in advance. For this reason, measuring partial discharges can help prevent costly damage. The TE measurement is thus used for quality testing and diagnosis in the factory as well as during on-site testing of cables, GIS, power transformers and transducers or rotating machinery and their components
-
Product
Ultrasonic Concrete Testing
-
This category comprises the range of instruments that use sound or stress waves in order to determine the properties of concrete and other materials non-destructively. The first and most widely used System is our V-Meter, which utilizes the ultrasonic pulse velocity method for evaluating construction materials in the field. Transducers are available for a variety of frequencies from 24 KHz to 500 KHz. This unit has also been modified to suit the special needs of ceramics users and can be found as the Ultrapulse. The PIES, our revolutionary Portable Impact-Echo System, is an advanced instrument for non-destructive detection of flaws and defects in a variety of civil infrastructures ranging from bridges, parking structures and buildings to dams, piles, tunnels, tanks and marine structures.
