Polarity
See Also: Polarity Testers
-
Product
Conical Horn Antennas
-
Conical gain horns are offered as both standard and custom models with either a circular or rectangular waveguide interface. While conical gain horns with a rectangular waveguide interface can only support linear polarization, models with a circular waveguide interface can support various polarization types including horizontal, vertical, left-handed circular, and right-handed circular polarization for broader applications. The listed models operate across the full waveguide band and offer 23 dB nominal gain, 12 degrees typical half power beamwidth, a 24 dB typical side lobe level and 1.15:1 VSWR at center frequency. The below standard offering covers the frequency range of 8.5 to 140 GHz. However, other frequencies and standard models with 10, 15, 20 and 25 dB gain are also available.
-
Product
20kV 4 Collector Test Set
-
Polarity designs and manufactures the most reliable Microwave Tube Test Sets in the industry. Polarity understands the delicate structure of microwave tube devices and has built an extensive product line supporting the manufacturing process.
-
Product
Polarization Conditioners
Polarization Conditioner
High-speed software controlled polarization control and polarization scrambling with broad wavelength coverage, low insertion loss and back reflection.
-
Product
Smart Surge Protectors
SSP-30X
-
Progressive Industries Smart Surge Protectors (SSP) are portable RV surge protectors with the added benefit of a built-in polarity tester. The built-in surge indicator notes the condition of the surge protector. Additionally, the polarity tester (dual line for 50A) checks the status of the power source prior to use, Sleek, compact, portable design makes it easy to use and store. Designed for outdoor use. No installation required.
-
Product
120-600V Solenoid Voltage&Continuity Tester
1867
-
Peaceful Thriving Enterprise Co Ltd
Test voltage from 120-600V AC/DC polarity and continuity.
-
Product
Acoustic Imager
-
Can be used for quick on-site testing of current transformers in metering installations. They are designed and manufactured to test transformers’ primary current, secondary current, and turns ratio and identifies phase type and polarity.
-
Product
Insulation Resistance Measurement
MD 5060x
-
The Megabras MD-5060x is a smart, microprocessor-controlled, 5kV insulation tester and analyzer. Besides the conventional measurement of insulation resistances up to 5 TW, its advanced features allow to automatically measure both the Polarization Index and Dielectric Absorption Index, thus significantly simplifying testing of transformers.
-
Product
SMART MEGOHMMETER
MD-5060e
-
The Megabras MD-5060e is a smart, microprocessor-controlled, 5 kV insulation tester. Besides the conventional measurement of insulation resistances up to 5 TΩ, its advanced features allow to automatically measure both the Polarization Index and Dielectric Absorption Index, thus significantly simplifying testing of transformers.
-
Product
Twinax, Contact, Receiver, 50 Ohms
610113144
Twinax Contact (Receiver)
For increased reliability and to eliminate the need for polarization, the design of VPC’s Twinax contact consists of two concentric inner conductors for termination to a twisted pair, and an outer shield for termination of the cable shield.
-
Product
1.5µm PM Fiber Amplifier ( PM EDFA )
HAPM4000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM4000 is a Polarization Maintaining Optical Amplifier which working in 1528~1563nm operating wavelength. Adopt Polarization Maintaining Erbium-doped fiber (PM-EDF), output optical power range 13~26dBm, extinction ratio >20dB.
-
Product
Portable Electrical Management Systems
EMS-LCHW30
-
Progressive Industries Portable Electrical Management Systems (EMS) provide full RV protection against all adverse power conditions. You will feel secure with multi-mode surge, voltage, polarity and lost/open neutral protection. Each unit includes a digital display, scrolling continuously through the power source information: Voltage(s), current, frequency, error code, and previous error code (if applicable). Replacement parts are simply plug-and-play, making repairs quick and easy. As with our portable models, the computer is driven by state of the art microprocessors. Should the software ever change, EMS owners can receive a free upgrade at no cost.
-
Product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-20MH
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement for solar power system*Least affection from the magnetization of core and temperature fluctuation*DC leakage current measurements*Convenient ＋5V single polarity power supply
-
Product
Thermocouple Thermometers
-
Polarity: Automatic, positive implied, negative polarityindication.Low battery indication: The “ ” is displayed when thebattery voltage drops below the operating level.Measurement rate: 1 times/second.Operating environment: 0°C to 50°C at<70% R.H.Storage temperature: -20°C to 60°C, 0 to 80% R.H. withbattery removed from meter.Accuracy: Stated accuracy at 23°C±5°C, <75% R.H.Battery: 1.5Vx4pcs AAA size.Dimensions: 160mm(H) x 83mm(W) x 38mm(D).Weight: approx. 270g including batteries.
-
Product
NRZ Bit Error Rate Tester
-
Shenzhen Golight Technology Co.,Ltd
BERT integrates pulse pattern generator(PPG) and high sensitivity error detector(ED) to achieve the error rate measurement of data transmission in high speed communication. BERT can support multi-channel output and input and output polarity upset. It provides a best solution for the automated production test of the high speed optical transceiver.
-
Product
PXI Solid State Multiplexer, 10 Amp, Single 6-Channel
40-666A-012
Multiplexer Module
The 40-666A-012 is a single 6-channel 10A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
Voltage Tester, LED
72-9395
-
*Easy to use voltage tester designed for the professional user*Waterproof and rugged making it ideal for nearly all situations*Continuity test*690V max*Short circuit detection*Automatic range selection*Single lead voltage detection*Phase rotation test (50-60Hz)*Polarity detection*Built-in LED light*Rubberised grip*12 month limited warranty *view Terms & Conditions for details
-
Product
Digital ELCB (RCD) Tester
1813 EL
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2 Lines × 16 characters LCD.● Very low consumption.● Suitable for domestic version.● Better than 3% accuracy (current).● Menu-driven.● Accurate digital readout of disconnection time.● Accurate digital readout of disconnection sensitivity.● Automatic data hold function.● Zero crossing circuitry permit testing at 0° or 180°.● Disconnection phase polarity shown on LCD display.● Auto off and off override.● Polarity trip indicator (positive or negative phase)● Wiring polarity indicator.● Measure voltage between Line and Earth before testing.● 60Hz available.
-
Product
Ethernet To Parallel Digital Interface Boards
-
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
Product
MPO Visual Cable Verifier Kit
KI-TK824
-
Kingfisher's unique and innovate MPO Visual Cable Verifier Kit is a quick, versatile and inexpensive way to visually check MPO cable installations and patch leads for polarity and continuity, and overall end face condition. Just connect the source, and view the far end with the microscope to observe the repeating color pattern at the far end. Fiber 1 is easily identified with a winking light.
-
Product
Vector Network Analyzer
R42XXE
-
The R42XXE Vector Network Analyzers are designed for measuring of S-parameters, VSWR and impedance of waveguide networks in the full frequency ranges of standard waveguides between 33 and 170 GHz. Frequency accuracy is ±0.2%. The measurement range of reflection factor modulus is from 0 to 1. The measurement range of reflection factor phase is from 0 to ±180° for 0.1< |Гx|<1 with accuracy ±7.5 o in 18-75 GHz frequency range and ±9.6° in 75-170 GHz frequency range. The measurement range of transmission factor phase is from 0 to ±180 o with accuracy ±(5+0.1 |Ax|) o for Ax >-50 dB in frequency range to 75 GHz, for Ax >-30 dB - to 170 GHz. Data can be displayed in the rectangular, Smith or polar diagrams. VNA requires Personal Computer with USB interface.
-
Product
Antenna, Tactical, Log Periodic
EM-6942 | 400 MHz – 4 GHz
-
The EM-6942 is designed for harsh environmental conditions and its folding elements and 2-section design simplifies transport and storage. The antenna can be mounted on a tripod or any ¼-20 mount and be positioned for horizontal or vertical polarization.
-
Product
EOS Tester
KT-200SG
-
This test instrument stands for the EMI(Electro Magnetic Immunity) ability test to the electric devices, electronic circuit boards & electric equipments. Recently this instrument is widly used in many companies in Korea & other countries to test the immunity to thier products-power supply, drive PCBs, communication systems, LCD display panels whether they are safe or not against the impulse & noise.All for the purpose, of this object, it generates 4 ~ 5 kinds of different impulse test waveforms.Output test voltage level : 5 ~ 200 V ImpulseOutput voltage polarity : Positive, NegativeType of waveforms
-
Product
Audio Fiber Tracer
CFT-810
-
Motorized Polarization Controller. In addition to its basic function of adjusting polarization states in multi channels, it also provides convenient ‘save and recall’ functions. As a Scanning PC, it provides very powerful ‘auto scan’ modes with variable scanning speeds. Polarization states can be manipulated by either manual adjustment or remote control (GPIB, RS-232) using two quarter-wave plates in each channel of the PC1600. Additionally, the auto scan mode of FIBERPRO’s Motorized Polarization Controller has been upgraded in LPC, and it shows another auto scan mode of four quarter-waveplates with higher polarization extinction ratio when connecting two channels at a high speed. PC1600 is an essential tool to complete fiber-optic, multi-channel measurement systems such as WDM/DWDM as well as R&D (i.e. PMD experiments), and manufacturing.
-
Product
Polarization Extinction Ratio Measurement
-
Rapid & Accurate measurement for PER, Angle, and Power. The most suitable light source for PER measurement.
-
Product
8-CH Isolated Digital Input Module
ND-6052
Data Acquisition Module
- Channels: 8 DI. 6 fully independent isolated; 2 isolated with common ground- Isolated Voltage: 5000 VRMS- Programmable input polarity
-
Product
6 Channel 6 kV/1 mA VME HV Power Supply
V6534
-
The V6534 is a 1-unit wide VME 6U module housing 6 High Voltage Power Supply Channels 6kV, 1mA. The board is available with either positive or negative output polarity; mixed version with 3 positive and 3 negative channels is also available.
-
Product
Imaging Station
-
Standard upright microscopes were not designed to work with temperature controlled stages. Microscopes are optimized to get the best possible image for a number of different techniques (phase contrast, DIC, polarized etc...) Unfortunately due to the confines of the standard microscope frame, it is not easy to get samples under the objective lens and into the stage.
-
Product
Multi-layer Short Circuit Locator
Toneohm 950
-
Polar Toneohms are ideal tools for the electronics production environment. Able to locate shorts quickly and accurately on both bare and loaded PCBs, they provide a very cost-effective means of minimizing repair and rework of faulty PCBs that have been identified by pass/fail testing on an ATE system.
-
Product
OBD-II Breakout Box
PPECB
-
The Power Probe OBD-II Breakout Box is a CAN Bus circuit tester compatible with 12 and 24 Volt systems. The tool connects directly into the Vehicle’s Data Link Connector (DLC) testing for any abnormalities such as shorting and reverse polarity at the pins. If shorting or reverse polarity is present, connecting the PPECB first will prevent harm before connecting a Diagnostic Scan Tool. The Breakout Box provides a live display of present communicating signals without having to use a Digital Multimeter. Additionally, you can quickly test the voltages at all 16 pins.
-
Product
CT Polarity Tester
DIR CT
-
SCOPE proudly introduces Dir CT, a CT Polarity Tester specially designed to verify correctness of polarity of current transformers cores in live EHV switchyards. Polarity test is one of the most common yet crucial tests required to be done on current transformers by commissioning as well as maintenance engineers. Even though it is commonly conducted check, there was no all in one simple tool available for this measurement. DIR CT fills this void to perfection, it is expected to significantly reduce the time taken for polarity checks on numerous CT in sub-station, especially during commissioning of new sub-stations
