Module Carriers
Carrier Modules are highly-integrated small footprint board-to-board connectible packages.
-
Product
Single 16 to 1 Terminated 50 600MHz PXI RF Multiplexer
40-765-001
Multiplexer Module
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
NI-9860, 2-Port, C Series Vehicle Multiprotocol Interface Module
783703-01
Interface Module
2-Port, C Series Vehicle Multiprotocol Interface Module—The NI‑9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI‑XNET platform, the NI‑9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while taking other data acquisition measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO chassis.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 67 GHz, 50 Ω, SMA-1.85, Remote Mount, Terminated, Failsafe
42-785C-473-TE
Multiplexer Module
The 40-785C-473-TE (PXI) and 42-785C-473-TE (PXIe) are triple failsafe SP4T 67 GHz with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI 10A Power Multiplexer, 4-Bank, 4-Channel (SP4T)
40-661A-101
Multiplexer Module
The 40-661A-101 is a single pole, 4-bank, 4-channel (SP4T) PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available.
-
Product
Signal, Module, Receiver, QuadraPaddle, 90 Series, 192 Position
510150115
Receiver Module
Primary mating module 510151105. (May mate with other ITA modules, as well.)
-
Product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 50Ω, MCX
40-870A-106
Switch Module
The 40-870A-106 (PXI) and 42-870A-106 (PXIe) are 50Ω RF switches with 6 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40/42-870A has been minimized by careful attention to the mechanical and electrical design.
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, 3GHz, 50Ω, MCX
42-872A-102
Multiplexer Module
The 40-872A-102 (PXI) and 42-872A-102 (PXIe) are 50 Ohm 4 to 1 PXI RF multiplexers with 2 banks in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of this RF MUX has been minimized by careful attention to the mechanical and electrical design.
-
Product
Precision DC Power Module, 50V, 3A, 100W
N6762A
Power Module
The Keysight N6762A is a 100 W precision DC power module that provides low noise, and precise control and measurements in the milliampere and microampere region with the ability to simultaneously digitize voltage and current, and capture those measurements in an oscilloscope-like data buffer. For leakage current or sleep-mode current measurements, add option 2UA for measurement capability down to 1 μA.
-
Product
8-Ch SPST 12A-250VAC 24VDC Mux
H62004700
Multiplexer Module
This module is ideal for switching up to 12A. Composed by eight relays organized in two trees of four with two relays (One in each tree) with NC contact available. The module is shielded in order to reduce the radiated interference in high current switchings.
-
Product
Voltage Input Module For Remote I/O
Module
The Voltage Input Module for Remote I/O features 2-, 3-, and 4-wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Voltage Input Module for Remote I/O from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, Terminated, 8GHz, 50Ω, SMA
42-882B-001
Multiplexer Module
The 40-882B-001 (PXI) and 42-882B-001 (PXIe) are single 50Ω 4 to 1 RF multiplexers with 8GHz bandwidth. The 40/42-882B range has automatic termination of unused signals and is available as a single MUX in one slot, a dual MUX in two slots, or triple and quad MUXs in three slots.
-
Product
LXI Single 32 Channel Fiber Multiplexer LC, Single-Mode
60-850-414
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI High Density Multiplexer, 20-Bank, 4-Channel, 2-Pole
40-615A-002
Multiplexer Module
The 40-615A-002 is a 20-bank, 4-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pinconnector.
-
Product
IDoor Module: 4-Ports Non-Isolated RS-232 MPCIe, DB37
PCM-24D4R2
Expansion Module
Meets Advantech Standard iDoor TechnologyPCI Express® Mini Card Specification Revision 1.2 compliantSpeeds up to 921.6 kbps for extremely fast data transmissionSupports any baud rate setting (50bps~921.6kbps)Supports both Isolated & Non-Isolated Protection with 2/4 Ports RS-232/422/485I/O address automatically assigned by PCIe plug & playOperating systems supported: Windows 2000/XP/Vista/7, and Linux 2.4/2.6OXPCIe952/OXPCIe954 UART with 128-byte FIFOs standardSupports Embedded Automation PC UNO-2200/2300/2400 seriesSupports Control DIN-Rail PC UNO-1200/1300/1400 seriesSupports Control Cabinet PC UNO-3200/3300/3400 seriesSupports Control Panel Computers TPC-xx81/xx82 seriesSupports Thin Client Panel Computers TPC-xx51 series
-
Product
Thermocouple, Module, Receiver, ICon, 96 Position
510160110
Receiver Module
Primary mating module 510161110. (May mate with other ITA modules, as well.) *Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
-
Product
PXI Signal Insertion Switch Module
Switch Module
PXI Signal Insertion Switch Modules, also known as fault insertion units (FIUs), provide a set of feedthrough channels, which make the switch transparent to the system when closed. You can open or short these channels to one of two fault buses, allowing you to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI Signal Insertion Switch Module can validate the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs). You can also use the FIU models for hardware-in-the-loop (HIL) applications and electronic reliability tests.
-
Product
E-Band Signal Analysis Reference Solution
Reference Module
The E-band signal analysis reference solution provides an effective measurement solution for today’s wideband signals as well as emerging communications standards. With the M1971E waveguide harmonic mixer, which provides a 55 to 90 GHz input; Keysight oscilloscopes, which provide excellent signal integrity; and the powerful 89600 VSA software, you have a high-quality wideband measurement solution. A simple user interface also provides integrated mixer setup, correction and LO optimization, allowing for accurate measurements.
-
Product
SMARC Short Size Module with Freescale i.MX6 Solo, DualLite, Dual or Quad Core Processor
LEC-iMX6
Computer on Module
The SMARC ("Smart Mobility ARChitecture") is a versatile small form factor computer Module definition targeting applications that require low power, low costs, and high performance. The Modules will typically use ARM SOCs similar or the same as those used in many familiar devices such as tablet computers and smart phones. Alternative low power SOCs and CPUs, such as tablet oriented X86 devices and other RISC CPUs may be used as well. The Module power envelope is typically under 6W.
-
Product
Signal/Micro Coax/Micro Power, Module, Receiver, TriPaddle, 90 Series, 77/8 Position
510104306
Receiver Module
This hybrid module provides 77 TriPaddle Signal positions and 8 Micro Coaxial or Micro Power positions in a single wide module slot enabling consolidation of wiring and preserving valuable space in the receiver.Primary mating module 510108278. (May mate with other ITA modules, as well.)
-
Product
128-Ch 0,250A-100VAC 24VDC Multiplexer/Matrix
YAV90128
Multiplexer Module
A unique YAV90128 module is able to do all combinations of signal computation at low frequency between the device under test and the various measuring instrumentation inside a test system.
-
Product
PXI Single 6-Channel 30A Solid State MUX
40-667-012
Multiplexer Module
The 40-667 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 30A of continuous current and switch up to 40V signals. The switches can sustain inrush currents in excess of 120A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
LXI Microwave Multiplexer, SP6T, 9-Bank, 50GHz, 50Ω, SMA-2.4, Terminated
60-800-709
Multiplexer Module
High performance RF multiplexer suitable for switching microwave signals up to 50GHz with automatic termination of unused signals
-
Product
Signal/Micro Power/Micro Coax, Module, Receiver, TriPaddle, 90 Series, 20/20 Position
510104323
Receiver Module
Signal/Micro Power/Micro Coax, Module, Receiver, TriPaddle, 90 Series, 20/20 Position.This hybrid module provides 20 TriPaddle Signal positions and 20 Micro Power or Micro Coax positions in a single wide module slot enabling consolidation of wiring and preserving valuable space in the Receiver.*Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode
40-850A-214
Multiplexer Module
The 40/42-850A-214 is a PXI/PXIe 4-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Signal Module, ITA, QuadraPaddle, 192 Position, Right Angle Contacts For Custom PCB Mounting (510 151 107 And 510 109 316)
510151121
ITA Module
This kit has everything you need to attach a VPC ITA Module to a custom designed PCB. This includes the right angle header (P/N 510 109 316) and the ITA Module (P/N 510 151 107).
-
Product
PXI High Density MUX BRIC, 40-Chan, 20-Pole
40-570-315
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PXI Dual 2 x 2 Fibre Optic (M Mode) STM62.5
40-860-522-M62.5
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
COM Express® Basic Size Type 2 Module with 6th Gen Intel Core™, Intel Xeon® and Intel Celeron® Processors (formerly codename: Sky Lake-H)
Express-SL2
Computer on Module
ADLINK announces a new COM Express Type 2 Computer-on-Module, based on the highly popular Intel® Core processors (formerly codenamed Skylake and Kaby Lake). The Express-SL2/KL2 supports all type 2 related legacy I/O and thereby allows customers to extend the production life of existing type 2 based systems for at least another 10 years.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 75Ω, SMB
40-835A-001
Multiplexer Module
The 40-835A-001 (PXI) and 42-835A-001 (PXIe) are single 75 Ohm 16-channel RF multiplexers in a single slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40/42-835A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
USB Axis Module
E1735A
Interface Module
The E1735A USB Axis Module is the electronic interface for the 5519A/B laser head used in the Keysight 5530 Laser Calibration System. It also provides the interface for the 10888A remote control unit (optional) and the A-quad-B encoder input (optional).
