Programmable AC Sources
See Also: AC Sources
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 2Ω To 239Ω
50-298-113
Programmable Resistor Module
The 50-298-113 is a high density programmable resistor card with 9 channels which can be set between 2Ω and 239Ω with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm
50-294-021
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 1.5Ω to 925Ω
40-251-121
Programmable Resistor Module
The 40-251-121 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 925Ω with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI Precision Resistor Module 4-Channel, 2 to 13.6k
40-297-131
Programmable Resistor Module
These PXI precision resistor modules provide a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Potentiometer Card 2-Channel, 12-Bit, 0 To 4k Ohm
50-296A-021-2/12
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-146
Precision Resistor Module
The 40-297A-146 (PXI) and the 42-297A-146 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 5.82 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PCI Precision Resistor Card 4-Channel, 1.5Ω To 925Ω
50-297-121
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Resistor Module 2-Channel 2R to 131k with SPDT
40-293-134
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Precision Resistor Card 4-Channel, 1.5Ω To 3.55kΩ
50-297-123
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 255 Ohm
40-294-013
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI High Density Precision Resistor Module, 6-Channel, 4Ω to 5.82MΩ
40-298-052
Programmable Resistor Module
The 40-298-052 is a high density programmable resistor module with 6 channels which can be set between 4Ω and 5.82MΩ with 0.5Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 255 Ohm With SPDT
50-293-113
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI High Density Precision Resistor Module, 3-Channel, 4Ω to 22.3MΩ
40-298-154
Programmable Resistor Module
The 40-298-154 is a high density programmable resistor module with 3 channels which can be set between 4Ω and 22.3MΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PCI High Density Resistor Card 6-Channel, 24-Bit, 0 To 16M Ohm
50-295A-121-6/24
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI/PXIe High Density Precision Resistor Module, 18-Channel
40-297A-015
Precision Resistor Module
The 40-297A-015 (PXI) and the 42-297A-015 (PXIe) are 18-channel programmable resistors with a range of 1 Ω to 920 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 3Ω To 102kΩ
50-298-034
Programmable Resistor Module
The 50-298-034 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 102kΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
AC Power Source
6500 series
-
The global AC power testing requirements demand more sophisticated AC Power Source that is capable of simulating a wide variety of AC line conditions, harmonic waveforms, accurate power measurement and analysis. The Chroma 6500 series Programmable AC Power Source delivers the right solution to simulate all kinds of normal/abnormal input conditions and measure the critical characteristics of the product under test. It can be used for R&D design characterization, production testing, and QA verification of commercial, industrial, and aerospace electronic products. The Chroma 6500 series delivers maximum rated power for any output voltage up to 300 Vac, and at any frequency between 15Hz to 2000Hz. It is suitable for commercial applications (47-63Hz); for avionics,marine, military applications at 400Hz or higher frequency; or for electrical motor, air-conditioner test applications at 20Hz. All models generate very clean sine or square waveforms output with typical distortion less than 0.5%. The Chroma 6500 series has built-in Direct Digital Synthesis (DDS) Waveform Generator to provide user programmable high precision waveform. For testing products under AC line distortion conditions, clipped sinewave can be generated with 0% to 43% distortion and amplitude from 0% to 100%. It also can simulate all kinds of power line disturbances such as cycle dropout, transient spike, brown out, phase angle, voltage and frequency ramp up (ramp down), etc.. Up to 30 harmonic waveforms are factory installed, and testing for compliance to AC line harmonic immunity standards can be easily achieved in the field.
-
Product
EMX-7XXX
Programmable Resistor Module
The AMETEK VTI Instruments EMX-7000 Series PXIe Precision Programmable Resistor Ladder modules provide four independent channels of programmable resistors. The EMX-7004 is capable of delivering exceptional stability and accuracy for any resistance value between 1 Ω to 16,383 Ω and can be adjusted in 1 Ω increments through the software application programming interface (API) or dynamic soft front panel.The EMX-7005, EMX-7006 and EMX-7007 are perfect for applications requiring higher resistance values, with programmable settings ranging from 163 kΩ to 16.383 Mohms, while the EMX-7014, 7015 and 7016 are ideal for general purpose applications not requiring ultra high accuracies.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 2Ω To 31.5Ω
50-298-110
Programmable Resistor Module
The 50-298-110 is a high density programmable resistor card with 9 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-144
Precision Resistor Module
The 40-297A-144 (PXI) and the 42-297A-144 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 1.51 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 470Ω
40-251-014
Programmable Resistor Module
The 40-251-014 is a programmable resistor module with 8 channels which can be set between 1Ω and 470Ω with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 3Ω To 102kΩ
50-298-134
Programmable Resistor Module
The 50-298-134 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 102kΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI High Density Precision Resistor Module, 18-Channel, 2Ω to 31.5Ω
40-298-010
Programmable Resistor Module
The 40-298-010 is a high density programmable resistor module with 18 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 5W Programmable Resistor Module, 1-Channel, 1.5Ω to 925Ω
40-252-121
Programmable Resistor Module
The 40-252-121 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 925Ω with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 2Ω to 26.7kΩ
40-252-032
Programmable Resistor Module
The 40-252-032 is a programmable resistor module with 2 channels which can be set between 2Ω and 26.7kΩ with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI Precision Resistor Module 9-Channel, 2 to 13.6k
40-297-031
Programmable Resistor Module
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 122Ω
40-252-012
Programmable Resistor Module
The 40-252-012 is a programmable resistor module with 4 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
PXIe-4139, ±60 V, ±3 A DC, ±10 A Pulsed, 20 W DC, 100 fA Precision System PXI Source Measure Unit
782856-02
Source Measure Unit
PXIe, ±60 V, ±3 A DC, ±10 A Pulsed, 20 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4139 is a high-precision, system source measure unit (SMU) that features 4-quadrant operation and sources up to 20 W of DC power. This module features analog-to-digital … converters that help you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. You can use the PXIe-4139 for applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
Product
PXI High Density Precision Resistor Module, 4-Channel, 3Ω to 13.6kΩ
40-298-131
Programmable Resistor Module
The 40-298-131 is a high density programmable resistor module with 4 channels which can be set between 3Ω and 13.6kΩ with 0.25Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-156
Precision Resistor Module
The 40-297A-156 (PXI) and the 42-297A-156 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 85.3 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
