Synchronizers
See Also: Synchronization
-
Product
PTP Toolbox
OSA 5410/11
-
The OSA 5410 Series is a family of compact and cost-effective synchronization distribution and assurance devices that bring the power of Syncjack™ to any network. Following a toolbox approach, the family members of the OSA 5410 Series can be utilized in a variety of network synchronization applications including IEEE 1588v2 Access Grandmaster, Boundary and Slave Clock, GNSS receiver and Primary Reference Time Clock (PRTC), synchronization signal conversion and sync probe applications.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 20 MS/s on 48 Channels
DN6.592-48
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Virtual Platform Simulation Acceleration
QuantumLeap
-
QuantumLeap is a parallel simulation performance accelerator that leverages a new synchronization algorithm to provide the fastest virtual platform software execution speed available. The execution performance of this new technology has been measured on average at 15 times faster than the nearest commercial solution using standard benchmarks.
-
Product
Automation Monitor
-
The Automation Monitor is a diagnostic system for remote analysis and troubleshooting of semiconductor capital equipment. The monitor is capable of delivering synchronous streams from strategically located video cameras, sound devices and data sources on the equipment.
-
Product
sbRIO-9235, Non-Enclosed, 10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
781579-01
Strain/Bridge Input Module
Non-Enclosed, 10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The sbRIO‑9235 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The sbRIO‑9235 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. Non-enclosed modules are designed for OEM applications.
-
Product
Embedded Vision And Processing FPGA
CrossLink-NX
-
*Instant-on configuration – IO configures in 3 ms, and device as fast as 8 ms*Two hardened 4-lane MIPI D-PHY transceivers at 10 Gbps per PHY / 2.5 Gbps per lane*Up to 37 programmable source synchronous I/O pairs for camera and display interfacing
-
Product
8-CH 14-bit 100 MS/s High-Speed PXI Express Digitizer
PXIe-9848
Digitizer
The ADLINK PXIe-9848/9848H is an 8-channel, 14-bit, 100 MS/s digitizer delivering both high-accuracy measurement results and high-dynamic performance. With a PXI Express bus interface and ample onboard acquisition memory up to 512 MB, the PXIe-9848/9848H can easily manage simultaneous 8-CH data streaming. High density and high speed digitizer features ideally position the PXIe-9848/9848H for applications such as LIDAR, radar signal acquisition, and PSU (Power Supply Unit) testing applications.The PXIe-9848 provides a flexible set of input ranges from ±0.2V to ±2V, software selectable 50Ω or 1MΩ input impedance, a wide variety of triggering options and tight synchronization capability, all maximizing convenience of use. In addition, ADLINK provides the PXIe-9848H, features a x15/x50 signal condition module providing both high input voltage range of ±100V and high dynamic performance, delivering the optimum solution to measurement range expansion in a PXI system.
-
Product
Entry-Level 4-Axis Servo & Stepper Motion Controller
PCI-8134A
Motion Controller
The PCI-8134A is a 4-axis entry-level motion controller. A PCI interface provides plug-and-play capability for easy maintenance, and supports up to 12 cards in one system, to control 48 motors. The PCI-8134A provides pulse train command output up to 2.4MHz and encoder input up to 2.4MHz in 4xAB phase mode. Programmable acceleration and deceleration allows flexible programming of in-house applications, and dedicated motion I/Os shorten system installation. The PCI-8134A also supports 2~4 axis linear interpolation for simplified synchronous motion. The PCI-8134A is a cost-effective motion controller enabling implementation and control of most of point-to-point, conveyer, and load-and-unloader applications.
-
Product
FD-11613, 8-Channel Temperature Input Device for FieldDAQ
785640-01
Temperature Input Module
8-Channel Temperature Input Device for FieldDAQ - The FD-11613 measures up to eight thermocouple channels. It features cold-junction compensation and open thermocouple detection with an LED indicator per channel to identify disconnected thermocouples. The FD-11613 has an ingress … protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11613 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11613 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. This device is ideal for test cell and outdoor environments.
-
Product
PXIe System Sync Module, 5 Port
M9033A
System Sync Module
The M9033A PXIe System Synchronization Module is a dual-slot, 5-port module that provides multi-module and multi-chassis synchronization and triggering for Keysight's modular instruments.
-
Product
PXI-5124, 150 MHz, 200 MS/s, 12-Bit PXI Oscilloscope
778757-02
Oscilloscope
150 MHz, 200 MS/s, 12-Bit PXI Oscilloscope—The PXI‑5124 high-resolution PXI oscilloscope samples up to 200 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution measurements with up to 150 MHz of analog bandwidth. The PXI‑5124 also features PXI synchronization and data streaming capabilities.
-
Product
IRIG Time Code Receiver for Computers (PCI Express)
TCR180PEX-EL
-
Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX-EL receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements).
-
Product
PXI-5153, 500 MHz, 2 GS/s, 8-Bit PXI Oscilloscope
780317-03
Oscilloscope
500 MHz, 2 GS/s, 8-Bit PXI Oscilloscope—The PXI‑5153 high-speed PXI oscilloscope has two channels with flexible settings for coupling, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 500 MHz of analog bandwidth and flexible measurement configurations. The PXI‑5153 also features PXI synchronization and data streaming capabilities.
-
Product
PXI-5105, 60 MHz, 8-Channel, 12-Bit PXI Oscilloscope
779685-02
Oscilloscope
60 MHz, 8-Channel, 12-Bit PXI Oscilloscope—The PXI‑5105 high-density PXI oscilloscope device has eight simultaneously-sampled channels with flexible settings for coupling, impedance, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with many channels that require up to 60 MS/s or 60 MHz of analog bandwidth. The PXI‑5105 also features PXI synchronization and data streaming capabilities.
-
Product
V-FullWaver
-
The V-FullWaver systems were specifically developed for precise full waveform time domain Induced Polarisation, Resistivity and SP measurements. Each system is fully independent; incorporating its own power source, GPS module and digital memory for up to 3 months continuous recording. The V-FullWaver is a dual channel Induced Polarisation, Resistivity and SP receiver. Continually recording at 10ms sample rate provides a full waveform record. It can be synchronized on the GPS PPS signal, allowing an easy process of the signal. Data on the memory can be downloaded directly on a simple USB stick from all the Fullwavers.
-
Product
PXIe-5745, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO Signal Generator
785597-02
FlexRIO Signal Generator
The PXIe-5745 enables direct RF generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s for generation up to 1.5 GHz or in a single-channel wideband upconversion mode at 6.4 GS/s. The PXIe-5745 is ideal for applications that require high channel density IF signal generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for generating predefined waveforms, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA for dynamically creating waveforms, signal modulation/demodulation, and other custom real-time signal processing.
-
Product
Radio Trigger Module
RTM3
-
The Remote Trigger Module 3, or RTM3 3, is a new generation of impact trigger device. It is designed to time synchronize a single seismic source unit with multiple seismic recorders. It can also be used to synchronize multiple seismic recorders. The RTM3 units use an internal high accuracy oscillator that is synchronized to GPS timing information. Each RTM3 unit requires an external GPS receiver with valid satellite information to synchronize the internal clock. Once the internal clock is synchronized the RTM3 can be used without any GPS signal for up to 10 minutes.
-
Product
PXIe-6547, 100 MHz, 32-Channel PXI Express PXI Digital Waveform Instrument
781011-03
Digital Waveform
PXIe, 100 MHz, 32-Channel PXI Express PXI Digital Waveform Instrument—The PXIe‑6547 is a digital waveform generator and analyzer for interfacing and basic characterization test with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 100 MHz and interfacing with user-programmable voltage levels that have a 100 mV resolution. The PXI‑6547 also features advanced synchronization capabilities for building integrated mixed-signal test systems, hardware comparison for bit-error test, and per-bank digital timing features.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 1.25 GS/s on 1 Channel
M4I.6630-X8
Arbitrary Waveform Generator
The M4i.66xx-x8 series arbitrary waveform generators (AWG) deliver the highest performance in both speed and resolution. The series includes PCIe cards with either one, two or four synchronous channels. The large onboard memory can be segmented to replay different waveform sequences. The AWG features a PCI Express x8 Gen 2 interface that offers outstanding data streaming performance. The interface and Spectrum’s optimized drivers enable data transfer rates in excess of 2.8 GB/s so that signals can continuously replayed at a high output rate. While the cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum waveform generators. So, existing customers can use the same software they developed for a 10 year old 20 MS/s AWG card and for an M4i series 625 MS/s AWG.
-
Product
PXI-6115, 4 AI (12-Bit, 10 MS/s/ch), Buffer Size 16MS, 2 AO, 8 DIO, PXI Multifunction I/O Module
778194-01
Multifunction I/O
4 AI (12-Bit, 10 MS/s/ch), 2 AO, 8 DIO, PXI Multifunction I/O Module - The PXI‑6115 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. It is ideal for a variety of applications, such as stimulus/response applications where synchronization among analog input, analog output, and digital I/O is required, 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
L-Band RF Tuner and 2-Channel 400 MHz A/D with Kintex UltraScale FPGA - 3U VPX
Model 54891
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Two FPGA-based multiband DDCs (digital downconverters)- Xilinx® Kintex® UltraScale™ FPGA- Five GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Optional optical interface for data streaming- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
USB-6353 , 32 AI, (16-Bit, 1.25 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device
781441-01
Multifunction I/O
32 AI, (16-Bit, 1.25 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device - The USB‑6353 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6353 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
6-Channel 200 MHz A/D and 4-Channel 800 MHz D/A with Virtex-6 FPGA - 6U VPX
Model 58620
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Six 200 MHz 16-bit A/Ds- Two DUC (digital upconverters)- Four 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM; 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Ethernet/LXI generatorNETBOX 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 4 Channels
DN2.653-04
Arbitrary Waveform Generator
The generatorNETBOX DN2.65x arbitrary waveform generators (AWG) is a general purpose multi-channel AWG with outstanding dynamic performance. The series includes LXI units with either four, eight or 16 synchronous channels. The large onboard memory can be segmented to replay different waveform sequences.
-
Product
AdvintDAQ™ Data Acquistion
MAKO
-
The Mako platform is based upon use of NI CompactDAQ (cDAQ) product line consisting of a chassis, NI C Series I/O modules, and a Windows host computer connected over USB, Ethernet, or Wi-Fi. Mako systems provide an easy, flexible, expandable platform to meet the needs of any electrical or sensor measurement system. They control the timing, synchronization, and data transfer between a host computer and up to eight (8) C Series I/O modules. A single Mako can manage multiple timing engines to run up to seven separate hardware-timed I/O tasks at different sample rates in the same system. Multiple units can also be daisy changed together for larger applications.
-
Product
Power System Recorder
TESLA LITE
-
ERLPhase Power Technologies Ltd
The new TESLA LITE is an economical user-friendly multi-timeframe power system recorder: Economical yet complete power system recording for custom applications in smaller substations. Easy to use intuitive software Simultaneous transient fault, dynamic swing and trend recording and event logging Fault location derived from single and calculated currents IRIG-B clock synchronization (modulated and unmodulated) Smallest footprint among recorders allows easy retrofit and installation 12 current, 6 voltage and 38 digital inputs
-
Product
4-Channel 200 MHz A/D with 32-Channel DDC with Virtex-6 FPGA - 3U VPX
Model 52662
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs- Up to 2 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factors provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Synchronous Generator
ZET 7090
-
Synchronous generator ZET 7090 is used for signal forming of sinus, implulse and saw-tooth shapes and has 2 synchronous channels. Generators can be used independently or within automation and control systems.
-
Product
Rack Data Acquisition System
TraNET EPC
-
The Elsys Data Acquisition Intrument TraNET EPC with its high channel density and robust housing is designed for highprecision measurements in industrial environments. It is a scalable system that may grow to a total number of 64 SE channels in one device. Several devices can be synchronized with the Elsys Sync-Link box.
-
Product
Video Timing Generator
VTG
-
The VTG Video Timing Generator provides up to ten video sync signals with which to synchronize CCTV cameras in the field. The VTG is intended to be used with the VTM Video Timing Meter to establish accurate timing of multiple CCTV cameras.
