Cable Fault Locators
Use time domain reflectometry to locate signal loss or a Murray loop bridge.
See Also: Cable TDR, Cable Sheath
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
Fault Insertion Unit
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
PXI 16-Channel 4-Bus 2A Fault Insertion Switch
40-197A-002
Fault Insertion Unit
This 16-channel fault insertion switch is primarily intended for routing simulated fault conditions in automotive and aerospace applications involving the reliability testing of safety critical controllers.
-
Product
PXI Fault Insertion Switch, 6-Channel, Two Fault Buses, 30 A, Hardware Interlock
40-191B-012-HI
Fault Insertion Unit
The 40-191B-012-HI is a PXI fault insertion switch with hardware interlock using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
Product
PXI Single Bus 64-Ch 2A Fault Insertion Switch
40-190B-101
Fault Insertion Unit
The Single Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 8 Channel
50-200-008
Fault Insertion Unit
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
Product
Single Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-201
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
Single Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-001
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
PXI Single Bus 64-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-401
Fault Insertion Unit
The Single Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 2 Amp, 2m, 250 Port
A500RMR-T-5C200
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
3-Pin Power D-Type Cable, Male to Unterminated, Tinned Ends, 0.5m
A003PM5-T-5A050
Cable Assembly
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Male, 1m HV, Exit Towards Pin 1
A050DM5-050DM5-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assy 9-Pin D-Type, F/F, 1m, HV
40-970-009-1m-FFHV
Cable Assembly
A 9-Pin D-Type Cable Assemby for general use constructed from PTFE Type C insulated wire. The connector assembly can be secured to the product by screwlocks.
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 1 Amp, 1m, 500 Port
A500RMR-500RMR-0A100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products).
-
Product
4-Pin Power D-Type Cable, Male to Male, 0.5m
40-970-404-0.5m-MM
Cable Assembly
The 4-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG) Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Cable Assembly, 104-Pin D-Type, Male to Unterminated, Ferrules, 2A, 2m
40-972-104-2m-MU
Cable Assembly
This 2m long male to untermiated 104-Pin D-type Cable Assembly is suited for direct connection to various products using the 104-Pin connector. It is constructed from high-flexibilty, high-specification fully screened cable and has unterminated ends with ferrules.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 20", 2 NI SH96F-96M-RES 96
540256010140
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 20", 2 NI SH96F-96M-RES 96 pin connectors with resistors
-
Product
Cable Assembly, 200-Pin LFH, Female (Female Screwlocks) to Unterminated (Tinned Ends), 0.5m
40-972B-200-0.5m-FU
Cable Assembly
This female rear exit to unterminated 0.5m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, unterminated with tinned ends. The connector assembly can be secured to its mating connector by female screwlocks.
-
Product
Cable Assembly, Receiver, TriPaddle/Coax, 20", 68-PIN Male VHDCI, 4 SMA Plugs, 2 SMB Plugs
540170010143
Cable Assembly
Cable Assembly, Receiver, TriPaddle/Coax, 20", 68-PIN Male VHDCI, 4 SMA Plugs, 2 SMB Plugs.
-
Product
51-Pin REDEL High Voltage Cable Assembly, Male To Unterminated, Ferrules, 0.25A, 1m, 29 Wires
A051KMR-F-HA100-29
Cable Assembly
This is a 1m long male to unterminated 51-Pin REDEL high voltage cable assembly with ferrules constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips areprovided to secure the connector to associated product.
-
Product
Tool, Locator, TriPaddle, Receiver
910104127
Locator Tool
Used with crimp tool part # 910 101 103 to crimp TriPaddle receiver contacts to 20-28 AWG wire. This locator contains an integrated wire stop for consistent contact crimping.
-
Product
20-Pin GMCT Cable, Female to Female, 10A, 0.5m
A020GFR-020GFR-0B050
Cable Assembly
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
GPIB Cable, 0.5 Meter
10833D
GPIB Cable
The Keysight 10833D (0.5 meter) GPIB cable is engineered for exceptional reliability and durability even under the harshest conditions. When you buy Keysight GPIB cables, you can be sure of automatic, seamless compatibility between computers and instruments throughout your system. GPIB interface cables, cards, and software for your computers make it easy for you to access and control instruments and exchange data - and it all starts with the cables to connect your computer and instrument. Keysight GPIB cables are fully compatible with the IEEE 44.1 mechanical specification.
-
Product
Cable Assembly, 26-Pin D-Type, Male to Unterminated With Ferrules, 2m
40-972-026-2m-MU
Cable Assembly
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Cable Assembly, Receiver, TriPaddle, 36", 20-Pin Power Connector
540145010201
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 36", 20-Pin Power Connector
-
Product
SHC68-C68-D4, Shielded Single-Ended Cable, Low Leakage, 1m
152870-01
Digital Cable
68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, Shielded Digital Cable - The SHC68-C68-D4 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
Product
SH68F-68F-EPM, 68-Pin Female to 68-Pin Female, Twisted Pair, Shielded Multifunction Cable
199006-02
Multifunction Cable
68-Pin Female to 68-Pin Female, Twisted Pair, Shielded Multifunction Cable - The SH68F-68F-EPM Cable, sometimes referred to as SH68-68-EPM, connects NI DAQ 68-pin devices to 68-pin accessories. The SH68F-68F-EPM Cable has D-type connectors and is offered in different lengths.
-
Product
Cable Assy 78-Pin D-Type M/M 1m
40-970-078-1m-MM
Cable Assembly
A 78-Pin D-Type cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable to its associated products. The 78-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
SH68F-68F-EPM, 68-Pin Female to 68-Pin Female, Twisted Pair, Shielded Multifunction Cable
199006-01
Multifunction Cable
68-Pin Female to 68-Pin Female, Twisted Pair, Shielded Multifunction Cable - The SH68F-68F-EPM Cable, sometimes referred to as SH68-68-EPM, connects NI DAQ 68-pin devices to 68-pin accessories. The SH68F-68F-EPM Cable has D-type connectors and is offered in different lengths.
-
Product
Cable Assembly, Receiver, 36", QuadraPaddle to 2 x 78-Pin Female D-Sub Connectors
540112050240
Cable Assembly
Cable Assembly, Receiver, 36", QuadraPaddle to 2 x 78-Pin Female D-Sub Connectors
-
Product
3-Pin Power D-Type Cable, Female to Unterminated, Cut Ends, 0.5m
40-972-403-0.5m-FU
Cable Assembly
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
