-
Product
High-power DC Electronic Load (6kW~60kW)
FT68200A/AL/E Series
-
Shenzhen FaithTech Technology Co., Ltd.
FT68200 series high performance high-power DC electronic load provides three voltage ranges 150 V/600 V/1200 V, maximum current 2400 A per single unit, stand-alone power from 4 kW to 60 kW, expandable up to 600 kW, 10000A by master-slave paralleling. Ultra-high power density, 6kW is with only 4U height. Wider operating region, faster dynamic frequency, as well as transient mode, OCP/OPP test, sequence test, automatic test and battery discharge test functions greatly enhances its test strength and expands application coverage. Furthermore, two times instantaneous overpower loading capability can effectively reduces user’s test cost. Built-in standard RS232, RS485, LAN, USB (serial), optional GPIB and CAN interface, supports SCPI, ModBus RTU and CANopen protocol, which facilitates system integrators. FT68200 series has full protection functions, which can be applied to power battery discharge, DC charging station, charging piles, charging pile modules, vehicle On Board chargers (OBC), high-power switching power supplies, power electronics and other power electronics products.
-
Product
Dielectric Material Test Fixture
16453A
Test Fixture
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
VLSI Test Systems
Test System
50/100 MHz clock rate50/100 Mbps data rate1024 I/O pins (Max :1280 I/O pins)Up to 1024 sites Parallel testing32/64 M pattern memoryVarious VI sourceFlexible HW-architecture (Interchangeable I/O, VI, ADDA,)Real parallel trim/match functionTime & frequency measurement unit (TFMU)High-speed time measurement unit (HSTMU)AD/DA test optionSCAN test option (max 1G M/chain)ALPG test option for embedded memorySTDF tools supportTest program/pattern converter(J750, D10, V50, E320, SC312, V7, TRI-6020, ITS9K)User friendly windows 7 environmentCRAFT C/C++ programming languageSW (Software) same as 3380P & 3360P
-
Product
Dielectric Test Fixture
16451B
Test Fixture
The 16451B is used to evaluate the dielectric constant of solid dielectric materials accurately, and complies with ASTM D150. The 16451B employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixture.
-
Product
Digital Auto Multi-Meter
-
This Digital Auto Multi-Meter (DAMM) was designed solely for Automotive Technicians for troubleshooting all electrical problems encountered in the vehicle. Be it a 6V, 12V or 24V system it can be used to check Amps draw directly on the fuse (Mini, ATC or Maxi Fuses) without having to remove it and measure parasitic drain current using the parallel method at the fuse box.
-
Product
Rail Pressure Tester
RPT-5
-
The RPT-5 device is used for performing an independent, parallel pressure measurement in storage fuel systems such as Common Rail (Diesel) and GDI/FSI (petrol). The tester, apart from pressure value, also diagnoses power supply of a sensor. Additional advantage is the capability of automatically detecting the terminals of the sensor, which is useful especially when using needle probes.
-
Product
EM Solver System Level Solver
EMA3D
-
Electro Magnetic Applications, Inc.
MA3D is a powerful 3D numerical solution of Maxwell’s curl equations based on the time-domain finite-difference method in rectangular coordinates. The code has application to nearly any EM coupling, radiating, or interaction problem. EMA3D’s FDTD approach is the only EM tool capable of capturing the detail of entire aerospace or ground systems down to individual electronics interfaces in a computationally accessible manner. Computational advances and parallelization allow for fidelity once only dreamed possible.
-
Product
Phasing Sticks
-
High voltage phasing rods enable phase comparisons to be made at the point of paralleling two circuits without the interposition of voltage transformers or secondary wiring circuits.
-
Product
Industrial Computer
-
Renice 6U VPX Computer complies with OpenVPX Vita65 specification. It adapt GPGPU architecture, on board ARM processor and compatible with industrial and rugged design on the structure. It applied in the high-performance computing center, high-performance display, parallel computing, and computing cluster application, eg Ground Radar, Airborne Radar and Shipborne Radar.
-
Product
Integrating Spheres
-
Integrating spheres are used especially for measuring divergent light sources such as LEDs. The light is introduced through the input port, then reflected many times by the highly reflective interior of the sphere until it illuminates the inner surface uniformly. A detector samples a small fraction of this light to measure the total power input. Ophir integrating spheres have a highly reflective diffuse white coating for measurements independent of beam size, position and divergence. There are several sphere sizes, apertures and wavelength regions available. The large IS6 series has 2 configurations for measuring divergent or parallel beams.
-
Product
DC Power Supply
◎PW-4063R
-
*Use Toroidal Transformer. Low EMI & High EMS.*Triple output, 0-32V/0-6A X2 and 5V/3A .Max. 400Watts*Tracking operation. Max. output 64V/6A on tracking series or 32V/12A on tracking parallel.*4 display, Green LED shows Voltage and Red LRD shows Current. Easy to read.*Compact design. G.W. 9Kgs only. Easy to handle.*The resolution of PW-4063R as high as 0.01v and 0.001A.*Provide 4Pcs 10turns micro adjust VR for Voltage and Current adjustment. Easy to operate.*Very low Ripple & Noise, less than 0.4mVrms. Very suit for precise measurement.
-
Product
Autocompute LCR-Q Meter Sorter
Model 4912 / 4912PR
-
- Microprocessor based Fully Automatic L, C, R, Q and D measurement- Autoranging with Direct Digital Readout- 4 Terminal Measurement Technique- No Tuning or Balancing- Series or Parallel Equivalent Measurement- Absolute Value and Nominal Value with Percentage Tolerance- Single / Multiple Parameters Check During Component Sorting- Feather Touch Keys with Audio Feedback- Thermal Shut Down for Overheat Protection- Special Mechanism for Fast and Easy Insertion and Removal of Test Component- Low Cost and Portable- Component Sorting on Absolute or Nominal Value Basis with a Percentage Tolerance- Aplab Model 4912PR is Remote Programmable Auto Compute LCR-Q Meter Sorter, Which can be Programmed through GPIB, RS232 or SPIB Interface
-
Product
Bipolar/FET/Diode Dual Head Production Test System
36XX
-
Two test stations on the 3600E and 3601E systems. Performs DC, AC, and pulsed tests. Excels at evaluating difficult to measure parameters on zeners, current limiters, varactor tuning diodes and darlingtons. 24 bin opto-isolated handler/prober interface. Parallel first-in first out computer to tester interface for maximum throughput. Parallel testing with a 3602E or 3603E allows shared test execution for extremely high throughput applications when interfaced to high speed handlers with multiple test sites.
-
Product
Advanced SoC/Analog Test System
3650
Test System
Chroma 3650 is an SoC tester with high throughput and high parallel test capabilities to provide the most cost-effective solution for fabless, IDM and testing houses.
-
Product
WLCSP Probe Heads
-
Smiths Interconnect offers Wafer Level Chip Scale Package (WLCSP) Probe Heads utilizing spring probe technology which provide high parallelism in test, superior signal integrity and high speed / RF testing capability.
-
Product
PCI to PC/104+ Bus Adapter
327/328
-
Model 327 and 328 are bus-to-bus adapters that allow operating a PCI board from a PC/104+ card stack. They allow selection of important PC/104+ signals using jumper plugs, thereby avoiding the requirement of using hardwired settings. Model 327 aligns the PCI board parallel to the PC/104+ boards, while model 328 places it perpendicular.
-
Product
Serial And Parallel Port For PCIe
DTA-2142
-
Serial and parallel interfaces for ASI and SD-SDI, supporting multiple electrical standards including M-LVDS and LVTTL. Clock rates up to 108MHz are supported.
-
Product
SAFETY TESTERS ( CURRENT LEAKAGE TESTERS )
ST-05
-
Safety Tester Model ST-05 is a test set for testing small equipment powered by 120V 60 Hz, from an approved U-ground source. Test also can be run on double-insulated tools an on appliances with two-pin parallel plugs.
-
Product
GPGPU Processor
VPX6-4955
-
Curtiss-Wright Defense Solutions
The VPX6-4955 delivers incredible processing power from not one, but two NVIDIA Quadro Turing TU104 GPUs, providing a remarkable 6144 CUDA cores for parallel processing and a 50% improvement in performance per CUDA core compared to the previous Pascal generation.
-
Product
Multi-Instrument BERT Software
N4980A
-
The Keysight N4980A multi-instrument BERT software provides the ability to control multiple instruments through a rich Windows-based graphical user interface (GUI). Bit error rate measurements are simple to set up with the intuitive control screens. The software is ideal for setting up and performing parallel BER measurements and jitter tolerance testing (N4980A-JTS) in multi-lane and SERDES devices. You can also create your own patterns using the powerful editing tools built into the pattern editor to meet your unique requirements.
-
Product
VLSI Test System
3380P
Test System
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (512 I/O pins to test 512 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
CDMA2k Analysis Using NI PXI RF Test Instruments
NI-RFmx CDMA2k
Test Instrument
NI-RFmx CDMA2k is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
Product
Ethernet To Parallel Digital Interface Boards
-
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
Product
Ethernet To Parallel Digital Interfaces
-
ICS's 8063 Ethernet Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications.
-
Product
Configurable OSAT Friendly Pick-and-Place Handler
Delta Eclipse
-
Eclipse delivers scalable performance for testing a wide range of semiconductors, from analog ICs to high-performance CPUs and mobile processors. The Eclipse is a high-speed pick-and-place handler designed to test up to 16 Integrated Circuits (ICs) in parallel, at temperatures from -45°C to +155°C*, with throughput up to 13,000 UPH.
-
Product
Automatic Span Gasgenerator Unit
ASGU-370 Series
-
The multi point calibration units ASGU-370 series is designed for simultaneous (parallel) or step by step (serial) checking of gas analyzers. It is primarily installed in laboratories for quality assurance and is also used for the production of gas analyzers.Furthermore are the calibration units as a Transfer standard in portable suitcase available. Here we have for ongoing quality control in field the versions all in one aluminum suitcase and for a flexible and back-friendly wearing comfort the ASGU-370TS SPLIT.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/15
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,46 kg
-
Product
Multi-Wafer Test & Burn-in System
FOX-XP
-
The key features of the new FOX-XP test cell that contribute to the cost-effectiveness of the solution include the ability to provide up to 2,048 "Universal Channels" per wafer, which allows the system to test all the devices on the wafer in parallel. The new "Universal Channel" architecture allows any channel to be any function (I/O, Device Power Supply (DPS) or Per-pin Precision Measurement Unit (PPMU)). This enhanced architecture now allows customers to perform per pin parametric testing, more extensive digital pattern test with deeper data stimulus / capture memory (32M per pin), and deeper scan (768M) optimized for BIST/DFT testing.
-
Product
Wafer Testing
Trio Vertical
-
SV TCL's TrioTM is a reliable solution for advanced wafer testing challenges, specifically full array and parallel probing. We offer a complete line of vertical probe card products, each designed for your unique application.
-
Product
Pole Detectors
-
The tip of the unit detects the field polarity. The magnet surface is placed parallel to the unit tip. Two 1.5V AA battery operated. Power ON Switch activates the sensors and gives visual indication in form of two LEDs placed on the arm of the unit.
