Synthesizers
A system for generating any of a range of frequencies from a single fixed timebase or oscillator. (http://encyclopedia.thefreedictionary.com)
-
product
PCI Synthesizer
SYNTH300 Series
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
product
RTM Actuator Signal Conditioning Board
MS 3630I
CPCI Rear IO Actuator Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on Primary and Secondary actuator interface. This card shall handle excitation signals, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
product
Synthesized Clock Generator
CG635
Stanford Research Systems, Inc.
The CG635 generates extremely stable square wave clocks between 1 µHz and 2.05 GHz. The instrument''s high frequency resolution, low jitter, fast transition times, and flexible output levels make it ideal for use in the development and testing of virtually any digital component, system or network. Clocks from 1 µHz to 2.05 GHz. Random jitter <1 ps rms. 16 digits of frequency resolution. 80 ps rise and fall times. CMOS, PECL, ECL, LVDS & RS-485. Phase control and time modulation. PRBS for eye-pattern testing. OCXO and rubidium timebase.
-
product
PXI Quad 4 to 1 Mux 1GHz 75Ohm 1.0/2.3
40-749-731
The 40-749 is a quad 4 to 1 RF MUX available in 50 Ohm or 75 Ohm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-749 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals
-
product
SWR True Antenna Analyzer
SWR True Antenna Analyzer is a versatile analyzer covering all major communication bands from 30MHz to 2700MHz. The SWR True will analyze antennas and cables. Measurements are represented graphically as VSWR or Return Loss plots. The built in PLL synthesized generator offers a superior accuracy with small step size. The internal operating system controls measurement, display and the I/Os allowing serial communication to PC, USB to memory stick and USB Serial communication. The I/O options are used to write plots to either memory sticks or to a connected PC, the I/Os can also be used to operate the instrument, giving commands and receiving data. For documentation reference the instrument has a real time clock. Multilayer menus are used to setup and control the operation of parameters. The SWR True instrument is small, handy and light weight battery operated with more than 6 hours of continuous operation on the internal NiMh cells. Feature with XML data handling and application viewer is included. Accessory kit with soft carrying bag, car charger and coax adapters for standard types.
-
product
Electromagnetic Environment Simulators
A2PATS® Products
Our A2PATS Family of Products are electromagnetic environment simulators built upon Textron Systems' open-architecture direct digital synthesizer technology, coupled with our proven user interface. Our easily programmable, plug-and-play modular architecture uses identical, phase-coherent, direct digital Synthetic Stimulus Instruments (SSIs) as the radio frequency (RF) source for all signals. These modular commercial RF Sources are easily configured in our commercial cabinets. Four standard configurations are available including single-cabinet, multi-cabinet, mini-A2PATS, and A2DSG™.The A2PATS Family consists of numerous commercial products including but not limited to A2PATS, A2DRI™, A2DSG and A2EOSTIM.
-
product
Mode Locked Synthesizer
IT9200
The ITS-9200 is a synthesized RF source with a flexible locking capability that allows it to be phase-locked to non-standard external references. It is specifically designed for synchronization to mode-locked lasers with pulse output frequencies in the 72-80 MHz region, although it can be easily modified to adapt to other reference frequencies.
-
product
2-6GHz Ultra Compact Digital Receiver
QR037
The Teledyne Defence & Space (TDS) Single Channel High Performance Receiver provides a new approach for ESM / ELINT applications, incorporating patented features offering wide band synthesized capability from 500MHz to 18GHz, with frequency extensions available up to 40GHz.TDS’s new QR037 digital receiver module combines high dynamic range RF down conversion and LO generation with digitisation and signal processing capabilities to provide a compact solution for a number of ELINT/COMINT and ESM applications.Excellent dynamic range and linearity is achieved through a combination of RF and digital down conversion stages coupled with high performance pre-selection and IF filtering.
-
product
PXI Quad 4 to 1 Mux 1.3GHz 50Ohm SMA
40-749-521
The 40-749 is a quad 4 to 1 RF MUX available in 50 Ohm or 75 Ohm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-749 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals.
-
product
6.8 GHz Wideband Synthesizer with Integrated VCO
ADF4356
The ADF4356 allows implementation of fractional-N or integer-N phase-locked loop (PLL) frequency synthesizers when used with an external loop filter and an external reference frequency. A series of frequency dividers at another frequency output permits operation from 53.125 MHz to 6800 MHz. The ADF4356 has an integrated VCO with a fundamental output frequency ranging from 3400 MHz to 6800 MHz. In addition, the VCO frequency is connected to divide by 1, 2, 4, 8, 16, 32, or 64 circuits that allow the user to generate RF output frequencies as low as 53.125 MHz. For applications that require isolation, the RF output stage can be muted. The mute function is both pin- and software-controllable.
-
product
High Frequency RF and Microwave USB Programmable Signal Generators
LMS Series
The Lab Brick LMS series of high frequency RF and microwave USB-compatible, synthesized signal generators cover a frequency range from 0.5 MHz - 20 GHz with low noise, fast 100-microsecond switching time, and fine 100 Hz frequency resolution. They require no additional DC supply voltage and offer advanced features such as phase-continuous linear-frequency sweeping, internal/external 10 MHz reference, and optional pulse modulation. GUI software can track and control several connected signal generators, simplifying multiple-signal test setups. Each device stores settings in internal memory, allowing it to power up in a specific instrument state.
-
product
Selective Level Meter
Model SLM620
- Digital Synthesized Local Oscillator- Two Selective Bandwidths : 20Hz, 3.1KHz- Wideband, Low Noise and Low Distortion Measurements- dB/dBm Operation- High Frequency Stability- Internal Calibration Facility- Recorder Outputs- Frequency Tracking Facility with Level Oscillator SLG620- Storage of Nine Spot Frequencies- Reference Level Set Facility- Autotune Feature- Operates on AC Mains or Internal Rechargeable Battery- Built in charger- Graphic LCD Display with Backlight
-
product
Signal Acquisition
277
The Model 277 is designed around the Texas Instruments ADS42LB69 16-bit ADC. The 250 MHz sample clock is supplied by either the on-board frequency synthesizer or an external source. The frequency synthesizer can be phase locked to the local 10 MHz TCXO or an external reference can be used to achieve system-wide phase coherence.
-
product
Diversity Receiver
R400a
The R400a is a high performance, triple-conversion, frequency synthesized, UHF receiver fully compatible with all Lectrosonics 400 series transmitters, and a number of analog models. The proprietary audio processing includes a DSP (digital signal processor) for very low distortion and a superior signal to noise ratio. The DSP eliminates a compandor and its artifacts to provide exceptional audio quality when operating in its native hybrid mode. Special DSP algorithms also provide compatibility modes for use with Lectrosonics 100 and 200 Series analog transmitters.
-
product
Reverse Transcription and Polymerase
ThermaStop-RT
RNA oligonucleotides from cells and viruses can be amplified for detection using the methods of Reverse Transcription and Polymerase Chain Reaction (RT-PCR). In a first step, a complementary strand of DNA (cDNA) is synthesized using a primer and reverse transcriptase. The cDNA is then amplified using standard PCR techniques. This can be accomplished by taking an aliquot from the reverse transcription reaction and adding a DNA-dependent DNA polymerase (e.g. Taq) and other reagents and then doing PCR. That method is commonly called "Two-step RT-PCR", or "Two-tube RT-PCR". Alternatively, all reagents, including both enzymes and gene-specific primers can be included in a single tube in order to do both reverse trancription and PCR without the need to open the tube between those reactions. That method is commonly called "One-Step RT-PCR" or "One-Tube RT-PCR". Both methods can include primers for a single target or for multiple targets (i.e. multiplex RT-PCR).
-
product
Phase Noise Analyzer and VCO Tester
FSPN
The R&S®FSPN phase noise analyzer and VCO tester is designed to provide both very high sensitivity and measurement speed for production and design engineers working in these fields characterizing sources such as synthesizers, VCOs, OCXOs, and DROs. It is the ideal instrument for demanding development and production phase noise and VCO analysis.
-
product
Multifrequency Clock Synthesizer - PMC
Model 7190
- Simultaneous synthesis of up to 5 different clocks- 8 SMC clock outputs- Ideal for A/D and D/A converter clock sources- Typical phase noise: -125 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 or 10 MHz- Four quad VCXOs allow selection from 16 different base frequencies- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 500 MHz- Control and status via PCI bus interface
-
product
Signal Generator Synthesizer
A versatile and precise instrument used in the testing, design, and maintenance of radio frequency equipment and systems. It is capable of generating continuous wave (CW) signals at a set frequency.
-
product
High Frequency Synthesizer
HFS Series 1.25” x 1” x 0.25”
*Surface Mount Package *Broadband Designs Available *Optional Internal Reference *Optional Reference Detect Switch *Internal Reference Output Available *Off-the-Shelf Products Available
-
product
Multifrequency Clock Synthesizer - PCIe
Model 7890
Simultaneous synthesis of up to five different clocks, Eight SMC clock outputs, Ideal for A/D and D/A converter clock sources, Typical phase noise: -125 dBc/Hz @ 1 kHz offset
-
product
Multifrequency Clock Synthesizer - 6U VPX
Model 5790
- Simultaneous synthesis of up to five different clocksEight SMC clock outputs- Typical phase noise: -105 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 to 100 MHz- Four quad VCXOs allow selection from 16 different base frequencies- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 700 MHz- Control and status over the VPX backplane
-
product
Direct Digital Synthesis (DDS)
Analog Devices’ world leading direct digital synthesis ICs incorporate features such as on-board comparators, RAM, PLLs, mixers, and registers. This makes them an ideal agile frequency synthesizer solution in systems for communications, test equipment, and radar.
-
product
Synthesized UHF Belt-Pack IFB Receiver
IFBR1a
Wireless IFB (interruptible fold back) systems are used for talent cueing and crew communications in broadcast and motion picture production. In other cases, the IFB system is used by directors and other management to monitor program audio during a production. The IFB R1a receiver provides simplicity and flexibility in a package that is intuitive for untrained users to operate.
-
product
Coherent DDS Modules
ITS has developed several custom Direct Digital Synthesizer modules that offer phase-coherent or phase-continuous operation at any frequency step size. These agile DDS modules can be programmed through direct parallel, Ethernet, or RS-232 interfaces.
-
product
Communication Systems
Tactical networking radio system comprising of transmit/receive modules, converters, synthesizer, RF switching, power supplies, controllers and an antenna array. The radio automatically selects the best communications path to create a self-forming, self-healing network.
-
product
FPGA Signal Processor
376
The Model 376 is designed around the Texas Instruments ADC12D1600 12-bit ADC. The 1.6 GHz sample clock is supplied by either the on-board frequency synthesizer or an external source. The frequency synthesizer can be phase locked to the local 10 MHz TCXO or an external reference can be used to achieve system-wide phase coherence.
-
product
Direct Digital Synthesizer (DDS)
Corech’s Direct Digital Synthesizer series offers 0.001Hz frequency step and 0dBm to +10dBm output power. These cost competitive, rugged and compact module are the ideal choice for RF & Microwave systems such as communication systems, test and measurement equipment, radar systems etc.
-
product
PCIe Direct Digital Synthesizer
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency, amplitude and phase control the Synth1000 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs the Synth1000, up to 4 separate profiles may be dynamically selected using externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation. Software support for Windows 8, 7, Vista, Windows XP and Linux is included. LabVIEW Labview source code available. For detailed specifications, please refer to the Synth1000 Manual.
-
product
Quad RF Driver
The Quad RF Driver contains four independent RF channels, each with an RF synthesizer, variable attenuator, and 1W power amplifier. The RF signal can originate from either the internal synthesizer or an external source via SMA input. All channels have independent frequency, phase, and gain settings and can be operated in one of two modes. The “Wideband” mode operates from 35MHz to 2GHz with a 3.472KHz resolution; over this range the frequency roll-off is approximately 0.5dB/100MHz. “Int-N Phase Adjust” mode allows the user to set and maintain a fixed phase relationship between all four channels. This mode is designed to operate between 300 and 460MHz with a 2MHz resolution. Two additional inputs are provided for an external frequency reference and digital modulation.
-
product
AC Power Source
APS-7000 Series
AC Power Source APS-7000 Series, the advanced direct digital frequency synthesizer (DDS) waveform is used to achieve high frequency stability, good continuity and accurate measurement.
