Partial Discharge Monitors
See Also: Partial Discharge, Partial Discharge Detection, PD, PD Test, Partial Discharge Test
-
Product
Leakage Current Monitor
-
To alert utility-line workers of overcurrent conditions on such aerial devices as insulated ladders and truck booms, the Chance Sentinel sounds an alarm if leakage current reaches a pre-set level.
-
Product
High Voltage Surge Current Monitors
HVSCM
-
Designed to be used with the Model HVST High Voltage Surge tester. The Surge Current Monitor allows simultaneously surge testing 20 units. The Surge Current Monitor monitors the current going through each unit under test at the time of the surge. If a unit under test breaks down or leaks, the Surge Current Monitor will identify the bad unit by lighting the corresponding LED. The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. In production testing we expect that most of the time the devices will pass. In the event that one should fail, the failed device would be removed and then all the parts would have ot undergo another surge test. Since most devices pass most of the time, simultaneous surge testing can be a real time saver.
-
Product
Real Time Monitor Interface
ANALYSIS 4N
-
It supports a management on the on-site equipment, such as to add subnets, to add subnet equipment, or to config equipment parameters, etc. Subnet fulfills the following applications: parallel communication, interaction with equipment, batch logging, downloading, configuration, ending, timing synchronization and system status viewing.
-
Product
Kafka Monitoring With RTView®
-
RTView Enterprise provides turnkey Kafka monitoring with pre-built dashboards. With over 30 pre-defined alerts and over 15 pre-built monitoring dashboards, users can deploy quickly without the time, skill and expense necessary to build or configure their own monitoring applications or dashboards.
-
Product
Monitoring & Simulation
-
ETAP Power System Monitoring & Simulation (PSMS) is at the heart of the ETAP Real-Time power management system. Power System Monitoring & Simulation is the smart choice for both small and large electrical utility systems, generation plants, industrial sites, manufacturing facilities, and off-shore oil platforms.
-
Product
Gas Monitor System
-
Henan Bosean Electronic CO.,Ltd.
Used to detect combustible, flammable and toxic gases, and oxygen depletion.
-
Product
Backup Battery Monitor And Switch
-
Renesas offers an automatic battery back-up switch, intended as a low-cost solution for the switching of systems between two power supplies; main and battery backup.
-
Product
NIBP Simulator for Testing Patient Monitors
SECULIFE BP PRO
-
The SECULIFE | BPPRO is the high-end product from the new range of NIBP simulators and is distinguished by a great variety of functions. It includes functions such as NIBP, IBP, ECG, temperature, arrhythmia, respiration, leak detection and much more. Specially developed to cover a great diversity of functions and nevertheless to ensure a compact design, the SECULIFE | BPPRO fulfills the requirements of modern medical technology. It makes no compromises with regard to functionality and input diversity. There's hardly another product with a similarly large range of features.
-
Product
10.1" 16:9 P-CAP Touchscreen Monitor
USC-M10
-
10.1" TFT LCD with LED backlight, 16:10 aspect ratio with 1280 x 800 resolution, Default with P-CAP touch (non-touch option available). IP65-rated front panel, USB-C connection, Supports Windows/Linux/Android OS.
-
Product
Cable Partial Discharge (PD) Spot Testing And Locating
PrecisePD
-
PrecisePD is an on-line PD Spot Testing and PD location system for Cables and Switchgear with advanced signal processing, used for the detection of PD in high noise environments.
-
Product
Mark I Single Setpoint Monitor
-
The Mark I is a self-contained unit featuring a single set point control. A simple two-step adjustment permits detection of an overspeed and/or underspeed condition at either 10% or 25% of operating RPM.
-
Product
Partial Discharge
-
Partial discharge (PD) is a local electrical discharge that occurs in imperfections or inhomogeneities. The partial discharge measurement is a so-called “non destructive test” to determine the quality of insulating materials. On the contrary of pure high-voltage test, th test item is not pre-damaged at low PD levels.
-
Product
Advanced Monitoring Probe
DVB-T/T2
-
Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor DVB-T and DVB-T2 signals at transmitter outputs, through its RF inputs (up to 4 in 1RU), as well as at modulator input and at Head-End/distribution links, through its ASI and IP inputs.
-
Product
Transformer Monitoring
-
MTE offers a broad range of products and solutions for the online gas-in-oil monitoring of transformers (online DGA). With its individual and modular system components MTE provides the optimal customer oriented solution for utilities, industries and transformer manufacturers.
-
Product
Ballast Water Monitoring Systems
-
Ballast water is essential for safe and efficient shipping operations and stabilizing steel-hulled vessels at sea. It provides a variety of critical functions, such as maintaining balance, stability, and structural integrity on non-cargo voyages or when cargo is unloaded. Ballast water is also used to compensate for fuel and water consumption during at-sea operations.
-
-
Product
SparkFun Single Lead Heart Rate Monitor
AD8232
-
The AD8232 SparkFun Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op amp to help obtain a clear signal from the PR and QT Intervals easily.
-
Product
Integrated Performance Monitoring Software
SQlive
-
SQlive™ is compact, ready-to-install software for monitoring the performance of streaming video, IPTV and Voice over IP. Compact and highly resource efficient, SQlive can be embedded into mobile handsets, media players, set-top boxes, home gateways and other CPE and end system devices.
-
Product
External Pyrometric Camera for Combustion Thermal Monitoring
PYROSCAN-U
-
Pyroscan-U is specifically designed to perform thermal monitoring and mapping of any object inside a kiln, furnace, boiler or reactor, while looking at the area of interest through a standard window, from outside the combustion chamber. This megapixel pyrometric camera captures both visible and infrared HDR (High Dynamic Range) images of the burning zone.
-
Product
Logger and Handheld Instruments for Temperature Measurement and Monitoring
-
Temperature measurement and monitoring is vital for the quality of temperature-sensitive products wherever they are studied, produced, stored or transported.
-
Product
Environmental Noise Monitoring System
E-Box LIVE
-
This is the ultimate solution to environmental noise monitoring. The LIVE comes equipped with a modem that connects directly to our Castle Cloud software allowing you to monitor your results from the comfort of your own desk. Combine this with the ability to customise your power supplies and you will see why this is the ultimate solution for environmental noise monitoring.
-
Product
Watchdog Timer and System Monitor Card
PCIe-WDG-CSMA
-
This multifunction Low Profile x1 PCI Express card contains a watchdog timer used to monitor the operation of your application program and operating system to initiate a system reset in case of a lockup. It can also monitor and control a variety of system hardware parameters. The card is 6.6 inches long and 2.535 inches seated height. I/O wiring connections are via a female DB25 connector on the card mounting bracket. Two models with increasing features are available.
-
Product
Event Monitoring System
Sigma 4
-
Sigma 4 utilizes the “Seismic Acoustic Monitoring” seismograph node. This is the most advanced, field-proven acquisition system in the world. It works seamlessly to provide the most fully integrated source control/recorder solution.*Autonomous Operation using Internal Storage*USB External Storage for Fast Data Collection*Use internal battery option or external power connection*Internal 3C geophone or external Geophone/Seismometer/Hydrophone/Microphone*Supports standard Ethernet equipment
-
Product
Environmental Monitoring
-
Is the processes and activities that are done to characterize and describe the state of the environment.
-
Product
Software for Current & Water Quality Monitoring Data Analysis
DataStudio 3D
-
Aanderaa, a Xylem brand, is a technology provider of oceanographic sensors, instruments and systems which are able to measure environmental parameters such as wave, current andwater quality (Dissolved Oxygen, Salinity, Temperature, Depth and Turbidity) over long deployments, several years.Data analysis is an important stage in all environmental monitoring campaigns. In many situations, users have to download and filter through large data quantities for analyses. DataStudio3D is a free data analysis software available to Aanderaa SeaGuard and SmartGuard users.To aid in data analysis, Aanderaa has developed their own propriety software, DataStudio3D which allows users to download field data and plot them on different graphical plots. This mode of data analysis can be carried out within minutes to help user to compare parameters, view trends, anomalies, and to control the data quality.
-
Product
KVS Rugged Igniter Tester With Current Monitor
4314
Tester
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
Product
Network Monitoring Tool
-
Motadata’s proactive network performance monitoring tool can be used to automatically discover network devices, interfaces, and applications. The network monitoring software in a multivendor IT environment ensures complete visibility of IT infrastructure. The unified view enables IT admins with a comprehensive picture of the overall IT health and also provides drill-down root-cause analysis, enabling them to resolve network issues even before they affect business processes. It facilitates monitoring of hybrid multi-vendor environment using 100+ pre-defined monitoring templates with immediate notifications on the set threshold values.
-
Product
Solar Energy, PV Monitoring
-
Apogee silicon-cell pyranometers feature a monocrystalline silicon-cell detector that has the same spectral response as a PV module. The sensors quantify shortwave radiation being harnessed as electricity.
-
Product
Radiation Monitor
-
The Radiation Monitor is the survey meter in measuring the beta, gamma and x-ray radiation. It is useful in monitoring the environment/home safety, nuclear, medical, mining and metal industries. It is also ideal for the border control, customs and cargo inspections.
-
Product
Electrical SCADA Monitoring
-
Model-driven SCADA & Monitoring provides an intuitive real-time visualization and analyses platform via intelligent graphical user interface, one-line diagram, geospatial view, and digital dashboards.
