3D X-ray
produces three dimensional images inspecting target object's surface and below.
-
Product
X-Ray And Gamma Detector Systems
-
The XR-100CR is a new high performance x-ray detector, preamplifier, and cooler system using a thermoelectrically cooled Si-PIN photodiode as an xray detector. Also mounted on the 2-stage cooler are the input FET and a novel feedback circuit. These components are kept at approximately -55 °C, and are monitored by an internal temperature sensor. The hermetic TO-8 package of the detector has a light tight, vacuum tight thin Beryllium window to enable soft xray detection. The XR-100T-CdTe represents a breakthrough in xray detector technology by providing “off-the-shelf” performance previously available only from expensive cryogenically cooled systems. The XR-100-CdTe is also suited for measuring gamma rays.
-
-
Product
3D Guidance®
-
The 3D Guidance® electromagnetic tracking solution delivers exceptional performance and value for OEM image-guided interventional and therapy systems and medical trainers that require real-time navigation tracking capabilities. The 3D Guidance solution tracks 6DOF sensors that can be embedded into OEM instruments such as ultrasound probes, rigid and flexible scopes, and laparoscopic tools. Continuous in-vivo tracking is maintained through difficult anatomy, even when sensors are out of sight. Low latency and fast update rates ensure the most subtle tool movements are instantly tracked and visualized within the OEM host interface. The 3D Guidance solution is available in the driveBAY™ and trakSTAR™ configurations, as based on the Electronics Unit. The trakSTAR is a standalone desktop unit that connects to a direct power source. The smaller driveBAY fits inside the drive bay of a computer, OEM imaging cart, or medical trainer/simulator, using the host’s power supply. Both share the same tracking accuracy and reliability. The ready-to-use configuration facilitates cost-effective integration and speeds time to market.
-
Product
3D Automated Optical Inspection
Zenith UHS
-
High-speed full 3D AOI that brings about a revolution in SMT process management Industry-leading speed for full 3D measuring inspection equipment skill solutions- Only solution in the industry to set inspection criteria according to IPC-610 standards- Performs defect diagnosis through measurement-based data and eliminates the causes of possible errors- Powerful 3D solder joint inspection
-
Product
Solid-State Battery X-Ray & CT Test Cell
STM1
-
Solid-state battery test cell designed for monochromatic X-ray and CT imaging, featuring an X-ray-transparent structure for non-destructive electrochemical and structural characterization.
-
Product
Constant Potential Generator Metal Ceramic X-Ray Tube 30 to 300 kV
CP300C
-
The CP300C is the first panoramic x-ray generator of the CPSeries product range. Equipped with a metal-ceramic tube, the CP300C is a light (less than 30kg) and powerful generator (300 kV), able to penetrate up to 52mm of steel in 10 minutes, making it the best power-to-weight ratio in the world.The efficiency of the CP300C is also maximum thanks to its real 100% duty cycle that allows longer exposure time (> one hour).A full range of accessories is available (holding bars, tripod…) and even a 60°x40° lead diaphragm to convert the CP300C into a directional unit.
-
Product
Multi-Channel X-Ray Fluorescence Spectrometer
FACTORY LAB MXF-2400
-
Wavelength Dispersive X-Ray Fluorescence Spectrometer The Shimadzu MXF-2400 is an improved version of the Shimadzu Multi-Channel X-ray fluorescence spectrometer, which has been rated highly in the overseas market as well as in the Japanese market. The latest hardware designed to fully utilize the principle of X-ray fluorescence spectrometry and the data processing unit that uses various software programs to permit automatic management of analysis data combine to provide high analytical productivity both in R&D and production control. Up to 36 elements can be simultaneously determined by the fixed monochrometer and up to 48 elements can be determined sequentially by the optional scanning monochrometer. High analytical precision is provided even in high sensitivity analysis of a few ppm quantity level.
-
Product
X-Ray and CT Inspection
-
Systems offer a microfocus X-ray source, a large inspection volume, high image resolution and is ready for ultrafast CT reconstruction. They cover a wide range of applications, including the inspection of plastic parts, small castings and complex mechanisms as well as researching materials and natural specimens.
-
Product
3D Building Scanning Services For Existing Conditions
-
Trusted by industries across USA, Tejjy 3D laser scanning company facilitates high-resolution reality capture of as-built data. Our on-site 3D scanning professionals gather accurate measurement with quality point clouds of as-built condition. We facilitate precision of 4-6 mm approx. in field measurement for renovation, surveying, facility management, digital twin, heritage preservation as per client requirements.
-
Product
3D Point Cloud Data Viewing, Cleaning, Editing, Leveling, and Alignment Software Package for BV5000 3D Data Processing
QuickStitch Powered by EIVA
-
QuickStitch is an easy-to-use 3D point cloud data viewing, cleaning, editing, leveling and alignment software package designed specifically for BV5000 3D data processing. The intuitive controls and user interface allows operators to quickly learn cleaning and alignment techniques. QuickStitch provides customers a fast and simple way to produce clean and aligned data sets to their customers.
-
Product
X-Ray Inspection System
TruView™ Cube
-
The Perfect Solution for a Powerful Small Form Factor X-ray Inspection System. The all new TruView™ Cube X-Ray Inspection System is a fully motorized radiography system developed to meet the stringent requirements of electronics assembly and component inspection. Ideal for applications where space is premium, the the TruView™ Cube X-Ray sits comfortably on your laboratory bench.
-
-
Product
Energy Dispersive X-ray Fluorescence Spectrometer
Pharmaceutical Elemental Impurities Analysis System
-
Control of Elemental Impurities in Pharmaceuticals In the pharmaceutical industry, the analysis of elemental impurities is necessary to ensure the safety of pharmaceuticals. In December 2014, the "Guideline for Elemental Impurities" (Q3D) was issued by the International Council for Harmonisation of Technical Requirements for Pharmaceuticals for Human Use (ICH), consisting of representatives from Europe, the U.S. and Japan. In Japan, the "Guideline for Elemental Impurities in Drug Products" (PFSB/ELD Notification 0930 #4 from the Ministry of Health, Labour and Welfare) was issued, and will be applied to new drug products submitted for approval after April 1 2017. For 24 elements categorized in Class 1 to Class 3, residual quantities in pharmaceutical drug products must be controlled within permissible limits. Although ICP-AES and ICP-MS are used for precise analysis of elemental impurities, X-ray fluorescence spectrometers can be used as an alternative analysis method. This is because they can quantitatively and qualitatively analyze a variety of elements nondestructively, and without chemical pretreatment, unlike ICP-AES and ICP-MS systems. The X-ray fluorescence spectrometry has been adopted as a general method of analysis in the U.S Pharmacopeia and the European Pharmacopoeia. (USP<735>, Ph.Eur.2.2.37)
-
Product
3D Roughness Measurement System
IF-Profiler
-
The If-Profiler is a handheld 3D roughness measurement system for high resolution measurement of surface finish. You measure roughness of flat and curved components with only one system. Measurements are performed both profile based (ISO 4287) and areal based (ISO 25178). The measurement system achieves flexible measurements and applications at high measurement speed. Various positions and measurement fields are traceably and intuitively measured. The IF-Profiler is also used to measure geometries with steep flanks and various coatings.
-
Product
3D Video Microscope
BVM-20102B
-
High-resolution CCD sensor, built-in analog/digital converter, analog and digital signal directly display on the screen, can also simultaneously display on TV and computer through corresponding interfaces; taking photo and video through software; easy operation, reducing user's fatigue and injury.
-
Product
3D Sound Intensity Analysis Software
DS-0225A
-
Finding out the position where the noise is occurring, and grasping the state of acoustic propagation are important ways to find effective noise countermeasure or improvement of acoustic environment.
-
Product
3D Ground Penetrating Radar data processing & Interpretation software
Condor
-
Condor is modern processing, visualisation and interpretation software for the efficient management of Raptor 3D GPR array data.Boost performance and improve workflows.- Efficient sub-surface imaging- Effective workflows- Simple and intuitive- Dedicated to processing Raptor data- Modern Windows software (64-bit)
-
Product
Desktop 3D AOI Series
MV-3 OMNI
-
- Exclusive 15MP / 25MP CoaXPress Camera System- OMNI-VISION® 3D Digital Tri-Frequency Moiré Technology- Leading-Edge 12 Projection Blue DLP Technology- Precision Compound Telecentric Camera Lens- Eight Phase Color Lighting System- 10MP / 18MP SIDE-VIEWER® Camera System- Programmable Z-Axis Multi-Focus System- INTELLI-PRO® Automatic Programming Software- Multi-Functional AOI-SPI Fusion Technology- INTELLISYS® Industry 4.0 Intelligent Factory Automation System
-
Product
X-Ray Preamplifier Power Supply
-
The X-ray Preamplifier Power Supply (XPPS) provides power for 50 or more preamplifiers. The 19-inch rack-mount or benchtop unit contains linear power supplies that generate +/-12V @ 5.1 Amperes and +/-24V @ 3.6 Amperes, with very little noise.
-
Product
Energy Dispersive X-ray Spectroscopy
EDS
-
Materials Evaluation and Engineering
EDS is an elemental chemical microanalysis technique performed in conjunction with each of the SEMs at MEE. Features or phases as small as about 1 micron can be analyzed.
-
Product
3D Solder Paste Inspection Machine (3D-SPI)
3Si Series
-
Saki's 3D SPI identifies critical defects and assists with process improvement.
-
Product
ROBOT-MOUNTED OPTICAL CMM 3D SCANNERS
METRASCAN-R
-
Part of the MetraSCAN 3D line-up, the robot-mounted MetraSCAN-R optical CMM 3D scanning systems are fast and accurate scanning solutions designed for 3D automated inspection of parts on the production line and on the shop floor. In combination with industrial robots, the MetraSCAN-R series increases the reliability, speed and versatility of on-line inspection and quality control (QC) process.
-
Product
Large-Area CMOS X-Ray Detector
Rad-icon
-
Teledyne DALSA’s Rad-icon product family of large-area digital x-ray cameras offers users a high-speed, high-performance x-ray imaging detector with a fast, reliable PC interface (either GigE or CameraLink) for easy integration.
-
Product
Dimensional Inspection (3D Inspection)
-
The 3D measurement data from our scanners and PCMMs offers a comprehensive definition of a physical object that is used for measurement, inspection, comparison and reporting. When a part is defined by millions of points, you can see subtle deviations, slight variations and fine details, which gives you the confidence that a part (or mold) meets your specifications. To deliver the best of both worlds, we combine 3D scanning with our contact, touch-probe measurement tools to deliver precise dimensions on geometric shapes.
-
-
Product
3D Optical Profilers
-
Bruker is the industry-leading provider of 3D surface measurement and inspection solutions, offering systems for fast, reliable, and easy-to-use non-contact analyses with best-in-class accuracy on samples ranging in size from microscopic MEMS to entire engine blocks. They provide researchers and engineers in R&D, manufacturing, and quality control the industry-leading sensitivity and stability necessary for precision 3D surface measurements in applications and environments that are challenging for other metrology systems.
-
Product
Packaged Food X-ray Inspection System
EPX100
-
Our revolutionary new x-ray system is so advanced it will not only improve your product safety and meet regulatory compliance but also will optimize and streamline your product inspection.
-
Product
Simple 3D Measurement & Inspection
XG-X Series Vision System
-
Abundant processing power is available even with multiple camera connections, including the 21 megapixel color camera, line scan cameras, or 3D cameras. XG-X Series offers high-speed, high-resolution cameras for high-accuracy inspection, providing powerful solutions for a variety of problems that arise in manufacturing.
-
Product
Proton Induced X-ray Emission (PIXE)
-
Elemental Analysis Incorporated, utilizing Proton Induced X-ray Emission (PIXE), provides a non-destructive, simultaneous analysis for the 72 inorganic elements from Sodium through Uranium on the Periodic Table for solid, liquid, and thin film (i.e. aerosol filter) samples. The PIXE technique offers the advantage of analysis, without the necessity for time consuming digestion, thereby minimizing the potential for error resulting from sample preparation.
-
Product
X-ray Fluorescence Measuring system
FISCHERSCOPE® X-RAY 4000 Series
-
Inline measuring with maximum endurance. Robust inline device for measuring on solid strips, punched grids with measuring structures from a few millimeters up to coated membranes or solid strips up to one meter wide.
