Timing Generators
-
Product
DC Power Supplies
-
Is the unidirectional flow or movement of electric charge carriers (which are usually electrons). The intensity of the current can vary with time, but the general direction of movement stays the same at all times. As an adjective, the term DC is used in reference to voltage whose polarity never reverses.
-
Product
Dynamically Controlled, High Voltage Digital I/O PXI Card With Pin Electronics
GX5055
-
The GX5055 represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the GX5050, the GX5055 offers high performance pin electronics and an enhanced timing generator in a compact, 6U PXI form factor.
-
Product
LXI WTB Terminator, 109.8 ohm
60-983-003
-
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
Product
12 Channel External Timing Board
0000-002
-
Timing Channels: 12 x 16 bit channels. Each can be programmed for event counting, elapsed time indication, rate generation, and programmable one-shot applications
-
Product
Time Code Generators
-
Masterclock's time code generators provide a source of very stable time code and accurate time and date information. The GPS500 extracts timing reference from GPS satellite signals and generate time code synchronized to within less than 10 microseconds of UTC (Universal Coordinated Time). It can output IRIG-B with and without IEEE 1344 date encoding, SMPTE/EBU, NMEA 0183, Kinemetrics/Truetime, and 1PPS.
-
Product
Dual Channel Multi-function Decommutator
LS-55-DD
-
The Lumistar LS-55-DD PCI Dual Multi-function PCM Decommutator offers two multifunction decoms and two optional bit synchronizers (LS-45) in a single PCI card slot. The multi-function decoms are implemented in FPGA using a next generation design based on the LS-50-P. The simulators,decommutators, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through a low-profile daughterboard. CVSD voice, h.261 video, and IRIG Chapter 8 decoding are achieved through software.
-
Product
Intelligent Time Reference
TM-4™and TM-4/OEM™
-
The Intelligent Reference/TM-4™ and TM4/OEM™ are multi- purpose, GPS disciplined timing signal generators and frequency references in economical off-the-shelf and custom configurations. Intended for use in a wide variety of timing, synchronization and frequency reference applications, they are based on the most advanced architecture Spectrum has ever offered, and include the most popular features of Spectrum's core platform for current timing products.
-
Product
Timing Signal Generator
OSA 5548C TSG
-
Our OSA 5548C Timing Signal Generator (TSG) is a scalable synchronization solution ranging anywhere from 20 unprotected outputs up to a thousand protected outputs by adding up to four expansion shelves to the core unit. Its ultra-compact footprint makes it ideal for telecom operators to provide scalable network synchronization in over-crowded exchanges. The OSA 5548C TSG’s distributed intelligence message passing system eliminates single points of failure and guarantees reliable uptime. Core unit and expansion shelves share the same modules, minimizing overall administrative complexity and enabling reduced homologation activity.
-
Product
Digital Pulser
HH2602
-
Handy, Quick and Easy to use tool. Accurate time base generator. 9 seleclable frequency puise output. LED opersation indication. Open collector output. Compact for in-circult trouble shooting. Size: 180mm x 30mm x 20mm
-
Product
Dynamic Data Simulator
LS-70-S
-
The Lumistar LS-70-S PCI Dynamic Data Simulator allows complex data streams to be generated for evaluation of bit synchronizers and PCM decommutator performance. It can also be used for uplink command generation to vehicles in flight, checkout of complete telemetry links, and playback of archived hard drive data in any format with the appropriate dll. The PCI board is only 7 inches long and contains the dynamic simulator and IRIG Time Code Generator.
-
Product
Transition Time Converter, 500ps
15433B
-
The new design of these transition time converters ensures very low signal reflection far beyond the 3 dB point, unlike conventional converters. Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications. The converters are fitted with SMA connectors, one male, one female. These converters have been designed to convert the fixed transition-times of the Keysight 8133A 3 GHz timing generator (<100 ps transitions) to slower, fixed transition-times (150 ps, 250 ps, 500 ps, 1 ns, 2 ns) hence reducing the signal bandwidth. All transition-times are from 10% to 90% of amplitude.
-
Product
TCSPC Lifetime Fluorometer
DeltaFlex
-
The DeltaFlex time correlated single photon counting (TCSPC) system is one of our Delta series of next generation time correlated single photon counting lifetime instrumentation. The DeltaFlex offers the ultimate in flexibility.
-
Product
IRIG-B Analyzer/Generator
APP-110
-
Battery powered• 3.5” backlit touchscreen display• Oscilloscope view• IRIG-B time signal decoder and analyzer• IRIG-B/1PPS time signal generator
-
Product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781262-01
-
PXI Vector Signal Generators offer custom and standard modulation, as well as the ability to generate communications standards formats such as GPS, WCDMA, DVB-H, and more. They support quadrature digital upconversion, which reduces waveform download and signal generation time, as well as stream-to-disk capabilities. The power and flexibility of PXI Vector Signal Generators make them ideal for use in scientific research, communications, consumer electronics, aerospace/defense, and semiconductor test applications as well as for areas such as software-defined radio, radio-frequency identification (RFID), and wireless sensor networks.
-
Product
Common Rail Injector Tester
ICR-4 Tester
-
ICR-4 tester is used to control electromagnetic and piezoelectric injectors used in the common rail injection systems. It is possible to control up to four injectors of a type at a time. The signal generated by the tester which controls the injectors, corresponds to the signal which appears in the car engine controller.
-
Product
96/48-CH Opto-22 Compatible PCI Express Digital I/O Cards
PCIe-7248/7296
-
ADLINK"s PCIe-7248/7296 are high-density parallel digital I/O boards with 96/48 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCIe-7248/7296 can utilize the Opto-22 external devices. The PCIe-7248/7296 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCIe-7248/7296 provides 4/2 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCIe-7248/7296 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCIe-7248/7296 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
Product
200 MS/s Waveform Generator & Dual 50 MHz Pulse/ Timing Generator
3172
-
The Racal Instruments™ 3172, a 200 MS/s Waveform Generator and Dual 50 MHz Pulse and Timing Generator, combines multi-instrument density and highfrequency performance in a single-slot, C-sized VXIbus format.Waveform output in the range of 100 μHz to 30 MHz with 16-bit vertical resolution (12-bit vertical for 3171 emulation) and pulse output to 50 MHz make the 3172 a powerful solution to a variety of test stimulus requirements.
-
Product
Time Code Generator
TCG
-
The TCG is an option for the SR-112 that enables the user to generate time code. Installation is very simple as it is software only and doesn’t require any hardware modification.
-
Product
Video Timing Generator
VTG
-
The VTG Video Timing Generator provides up to ten video sync signals with which to synchronize CCTV cameras in the field. The VTG is intended to be used with the VTM Video Timing Meter to establish accurate timing of multiple CCTV cameras.
-
-
Product
96/48/24-CH Opto-22 Compatible Digital I/O PCI Cards
PCI-7296/7248/7224
-
ADLINK"s PCI-7296/7248/7224 are high-density parallel digital I/O boards with 96/48/24 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCI-7296/48/24 can utilize the Opto-22 external devices. The PCI-7296/7248/7224 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCI-7296/7248/7224 provides 4/2/1 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCI-7296/7248/7224 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCI-7296/7248/7224 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
Product
Countdown Or Countup Clock Controller
RC600
-
The RC600 is a remote control that adds both countdown and countup timer control features to our NTDS and TCDS clocks. Reference or generate time input from NTP or time code (IRIG & SMPTE). Control a virtually unlimited number of time code clocks and network clocks.
-
Product
Mini Portable
-
An inexpensive palm-sized SMPTE time code generator intended for field use in multi-camera situations when its desirable (or necessary) for each tape to have the exact same time code for precise image matching during post
-
Product
10 Gb/s Programmable Digital Delay Line
PDDL10
-
The PDDL10 is a precision time delay generator for digital signals. Delays are controlled precisely in 5 increments from 0 to 635 ps.. Data rates through 10 gigabits per second are supported for very high-speed applications. Delays can be programmed via a TTL bus.
-
Product
Transition Time Converter, 250ps
15432B
-
The new design of these transition time converters ensures very low signal reflection far beyond the 3 dB point, unlike conventional converters. Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications. The converters are fitted with SMA connectors, one male, one female. These converters have been designed to convert the fixed transition-times of the Keysight 8133A 3 GHz timing generator (<100 ps transitions) to slower, fixed transition-times (150 ps, 250 ps, 500 ps, 1 ns, 2 ns) hence reducing the signal bandwidth. All transition-times are from 10% to 90% of amplitude.
-
Product
2nd Generation PCIe Multi-function Decommutator
LS-50-E
-
The Lumistar LS-50-E PCIe Multi-function PCM Decommutator offers a PCM decom, PCM simulator, time code reader/generator, and optional bit synchronizer in a single short PCIe card slot. The multi-function decom and simulator is implemented in FPGA using a next generation design based on the LS-50-P. The simulator, decommutator, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through an optional low-profiledaughterboard. CVSD voice decoding, h.261 videodecoding, and IRIG Chapter 8 decoding are achievedthrough software.
-
Product
Clock And Timing
-
Achieving highly accurate precision timing is no easy feat from a technology perspective, so it’s important to find a resource you can trust to reduce design risk and speed your time to market. Our end-to-end timing solutions generate, distribute and apply precise time for multiple industries, including communications, aerospace and defense, IT infrastructure, financial services, power utilities and more. We provide a broad range of clock and timing solutions ranging from MEMS oscillators to active hydrogen masers. Explore our portfolio of clock and timing components and systems to find the right solution for your project.
-
Product
High Performance 50 MHz Dynamic Digital I/O PXI Subsystem
GX5960 Series
-
The GX5960 digital subsystem represents the highest level of performance available for PXI-based digital instrumentation and features high performance pin electronics and a timing generator / sequencer in a compact, 6U PXI form factor. The GX5960 series consists of the GX5961 clock generator board with 16 driver / sensor channels and the GX5964 driver / sensor board which supports 32 bi-directional I/O channels. Up to 528 digital I/O channels can be supported by the GX5960 digital subsystem. Each digital channel features a wide drive / sense voltage range of -14 V to +26 V (maximum swing of 24 volts) which can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and a load value (with commutation voltage level) – offering the user complete flexibility when creating test programs and fixtures for multiple UUTs. In addition, each channel offers a parametric measurement unit (PMU) for DC measurements.
-
Product
GPS NTP Time Server - SYNTIME
-
Signals & Systems India Private Limited
Your product description goes hGPS NTP Time Server (SYNTIME) for Network Time Synchronization is a highly accurate time server. It generates time protocols to synchronize NTP/SNTP clients (Simple Network Time Protocol)/PTP clients (Precision time protocol IEEE 1588) over the network and operates at a speed of 10/100/1000Mbps. The NTP server accepts the time and frequency signals from sources like GPS or GLONASS. It achieves nanosecond accuracy and the system clock operates at stratum 1 when synchronized with time sources. It is a sleek, rack-mountable unit that synchronizes and maintains equipment/device time and avoiding any time drifts due to local RTCs. NTP output from time server supports unicast, broadcast, and multicast methods based on selection and behaves like a reference clock for the network. Apart from time synchronization protocols, it supports MD5 (Security key), SNMP, SSH, HTTP (Configuration), TELNET, FTP, and SYSLOG. IP address of the LAN ports can be field configurable.
-
Product
Digital/Pattern/PE Card
PE16S
-
The PE16S represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the PE16, the PE16S offers high performance pin electronics and an enhanced timing generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 256 bi-directional pins (16 boards). The PE16S offers 16 programmable level input or output channels with 2 PMU . The PE16S also supports deep pattern memory by offering 32 M of on-board vector memory with per channel dynamic direction control running test rates up to 66 MHz.
