Underground Cable
-
product
Underground Cable Fault Locator
KM-CFPL-620 /620B
Kusam Electrical Industries Limited
“KUSAM-MECO” underground Cable Fault Pre-locator is an automatic Cable Fault Locator which adopts ARM, FPGA & Dot Matrix Color LCD display Technology. This tester combines both pulse reflecting technology (TDR) & (intelligent Bridge testing (Bridge) (Model-KM-CFPL-620B) for measuring the exact fault location such as broken line, cross faults, earthing, (poor insulation & poor contact of the lead covered cables as well as plastic cables. (Model-KM-CFPL-620B)).It is a microprocessor based fault locator with a user friendly menu. It is easy to operate. It tests almost all telecom & signal cables. It has an English menu which is easy to understand & use. With Megameter & Ohmmeter it enables to test insulation resistance & loop resistance. It has USB Port for uploading test data to computer
-
product
Underground Cable Fault Locators
Techno Instrumentation (India) Private Limited
Complete range of underground cable fault locators. Manufactured in India.Surge GeneratorsReflectometer(Pre-locator) - Cable fault distance locatorCable fault finder/pinpointerHigh Voltage Murray LoopDC high voltage testersCable fault locating van
-
product
Fault Locator
VM-510FFL+
Finding the location of an underground cable fault just became easier with the VM-510FFL+ Standalone A-frame locator. Now locating a suspect cable and finding the fault can be done with the VM-510FFL+ and a compatible transmitter. There is no longer a need for a separate utility locator with cables connecting to it. After connecting a compatible transmitter to the line and placing it in a Fault-Find mode, use the simple to operate four button controls of the VM-510FFL+ to locate and stay on the cable path while pinpointing the sheath or ground fault.
-
product
Cable Testing and Diagnostics
BAUR Prüf- und Messtechnik GmbH
Testing devices are required for successful commissioning of underground cable networks or repairs. Diagnostic testing devices are used for evaluating the cable status, which enables optimised and anticipatory maintenance planning and thus minimises failures. This planning is best established with the BAUR diagnostics system.
-
product
Analog Voltmeters
*Dual stick MARK series measure voltage and perform phasing operations from 0V to 75kV*No batteries or calibration required*Determines in-phase or out-of-phase*Determines underground cable faults*Discharges underground cables and other equipment that hold capacitive charges*Versatile for overhead and underground applications
-
product
Earth Fault Indicator
The Sensorform Range of Earth Fault Indicators detects earth faults & short circuit faults on underground cables. A number of options are available for enclosure type, power source, indicator type, reset method, trip-level selection, and remote indication.
-
product
Air Core Shunt Reactors
Shunt Reactors act as absorbers of reactive power to increase energy efficiency of the power system. Shunt Reactors are inductors that are used in order to compensate capacitive reactive power generated by long and lightly loaded transmission lines as well as underground cables, thus allowing the flow of more active power through the system and avoiding over voltages. The shunt reactors provide inductive compensation.
-
product
Cable and Pipe Locator
PT-14
The locator PT-14 is used as an induction signal receiver in a cable tracing and fault location set for the following applications:• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.
-
product
CableSniffer
The CableSniffer is a revolution in locating faults in underground LV cables fast. Instead of relying on exploratory excavations, it samples and analyses the gases emitted when cable insulation starts to break down, via a series of 8mm bore holes.
-
product
Omnisens Securing Power Cable Integrity
https://www.omnisens.com/uploads/1/2/0/5/120592129/published/omnisens-cobra-logo-white-2014-06-10.png?1546958203
In both underground and subsea cables incipient faults often result in temperature events. Using optical fibers integrated into the power cable or laid close by, Distributed Temperature Sensing (DTS) helps detect changes and faults allowing the operator to intervene before the cable fails. It is suitable for deployment in any cable where an optical fiber is present, including HVDC, HVAC, export, inter-array, transmission and distribution.
-
product
Pre- Locator
CFL PL3
CFL PL3, new generation Cable Fault Pre-Locator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault with accuracy.
-
product
Vehicle Mount Cable Fault Location System
Weshine Electric Manufacturing Co., Ltd
VS2088Plus Built in Booster And Capacitor In Vehicle Underground Cable Fault Test Device
-
product
Pre- Locator
CFL PL3+
The new generation CFL PL3+ Cable Fault Pre-locator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 128 km.
-
product
Cable Fault Testers
*Compact and lightweight solution for underground cable testing*DC Hi-Pot test of de-energized, shielded underground primary cable*No external power required - self-contained 8kVDC voltage source*Can be used up to a distance of 1500 ft (457m)*Clear and simple test results - analog bar graph and indication of good or faulted cable*Safety feature - measures AC voltage before converting to a DC voltage tester*Lightweight, single hot stick operation for testing cable
-
product
Surge Generator
Surge Generator is the backbone of underground cable fault locator test systems. Surge Generator is used with a Prelocator for fault distance measurement and also used with a PinPointer for pinpointing the fault spot.
-
product
LV Iron Core Shunt Reactors
Iron core Shunt Reactors act as an absorber of reactive power to increase energy efficiency of the power system. Shunt Reactors are used in order to compensate capacitive reactive power generated by long and lightly loaded transmission lines as well as underground cables, thus allowing the flow of more active power through the system and avoiding over voltages. Shunt Reactors can be directly connected to the power line or to a tertiary winding of a three-winding power or distribution transformer.
-
product
Low Frequency Generator
LFG-50
• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.
-
product
Under Ground Cable Fault Locator
Widely used in electrical and power generation sector for testing underground cables in order to detect any fault.
-
product
Pin Pointer
CFL PP3+
The new generation CFL PP3+ Cable Fault Pin Pointer cum route tracer from SCOPE is the ultimate solution for locating of underground cable faults in minimum time by tracing cable route. It uses an advanced technology which helps even an unskilled operator to locate the fault accurately.
-
product
Wires and Pipe Locator
LKZ-720
*Detection of wires and cables (live or not)**detection of cables in ceilings, walls and floors,**detection of breaks in cables,**tracing cables in building installation,**locating power points and switches in buildings,**locating short circuits between leads,**tracing shielded cables,**tracing cables in metal ducts.*Identification of fuses on the distribution board.*Tracing underground cables.*Tracing conductive water and heating pipelines.*Non-contact detection of live cables.
-
product
Pre- Locator
CFL PL4+
The new generation CFL PL4+ Cable Fault Pre-locator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 256 km.
-
product
Cable Test Van
ETL-35K
ETL-35K system has a multitude of applications in electrical equipment testing and maintenance: testing cable insulation with DC (rectified) voltage up to 60 kV, measuring small leakage current of surge arrestors, high-voltage testing with AC voltage up to 100 kV at industrial frequency, underground utilities tracing, cable fault pre-location and pinpointing, and measuring capacitance and tan delta of various electrical objects at industrial frequency.
-
product
Pre- Locator
CFL PL2+
The new generation CFL PL2+ Cable Fault Prelocator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 50 km.
-
product
Cable Fault Locator
We are one of the leading manufacturers, exporters of suppliers of a premium quality range of Cable Fault Locator that is extensively used to trace and locate the fault of underground cables. This fault locator is manufactured at our hi-tech manufacturing unit as per international quality standards under the supervision of our professionals using superior quality components. Offered fault locator is made available in different specifications to meet the diverse requirements of the clients. Our honorable clients can avail this Cable Fault Locator from us at industry-leading prices.
-
product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Cut Ends, 1m
A015DF4-C-0A100
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
product
Cable Assembly, 200-Pin LFH, Male Bottom Exit (Male Screwlocks) to 4x50-Pin D-type, Female, 0.5m
A200LMB-04F050D5B050
This 200-pin male to 50-pin D-type female 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector and is constructed from 4 bundles of 50-wire flat/round ribbon cable. The connector assembly can be secured to the product by screwlocks. This cable assembly can be used with Pickering 50-Pin D-Type connector blocks (refer to 90-005D).
-
product
SHC68-68-EPM, 68-Pin Male VHDCI to 68-Pin Female D-SUB, 80 Twisted Pairs, Shielded Multifunction Cable, 1m
192061-01
The SH68M-68F-EPM Cable, sometimes referred to as SHC68-68-EPM, connects DAQ devices to accessories or cables with D-SUB connectors. You can use this cable to create custom cabling for your DAQ device. The SH68M-68F-EPM Cable is offered in different lengths. 80 twisted pairs, 1 connection used in shield. 81 total connections used.
-
product
Cable Assembly, 78-Pin D-Type, Female to Unterminated With Cut Ends
A078HF5-C-0A100
The A078HF5-C-0A100 is a 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. Has a 45 degree cable exit towards pin 1.
-
product
Cable Assembly, 50-Pin SGMC, Female to Unterminated, Cut Ends, 5A, 2m
A050FFR-C-0A200
This is a 2m long female to unterminated 50-Pin SGMC cable assembly with ferrules and is constructed from 19/0.18 (21AWG) Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
product
Cable Assembly, 3.5 mm (m) to 3.5 mm (m), DC to 26.5 GHz
11500E
The Keysight 11500E is a 61 cm (24 in) 3.5-mm male to 3.5 mm male cable assembly with a frequency range of dc to 26.5 GHz.
