Digital I/O
Input/output of digital values.
-
Product
32 Input, 32 Output USB Modular Digital I/O
U2651A
Digital I/O
The Keysight U2651A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5290 Series
Digital I/O
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
UIO40-Express Series
UIO-4030
Digital I/O Board
*1 2 wires RS-232*1 RS-485*8 GPIO (-24~24V input)
-
Product
Digital I/O Card
PCI-DIO-120
-
The PCI-DIO-120, PCI-DIO-96 and PCI-DIO-72 are parallel digital input/output cards designed for use in PCI-Bus computers. The same printed circuit board is used for all three models and is populated for 120 bits, 96 bits and 72 bits respectively. The card is 12.2 inches (310 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
-
Product
PXIe-7912, KU040 FPGA, 4 GB DRAM, x8 Gen 3 PXI Coprocessor Module
785173-01
Digital I/O
The PXIe-7912 provides a Xilinx Kintex UltraScale FPGA that you can program with LabVIEW or Xilinx Vivado to add signal-processing capabilities to PXI Express systems. Using the x8 Gen 3 PCI Express architecture and peer-to-peer streaming, PXI FlexRIO Coprocessor Modules can stream data to and from other modules in a PXI chassis at up to 7 GB/s without a host controller. You can pair these modules with another PXI instrument, such as a PXI Vector Signal Transceiver, to add functionality, such as running complex algorithms in real-time. The PXIe-7912 KU040 FPGA is ideal for applications that require a moderate amount of signal processing.
-
Product
4-Axis Quadrature Encode/Counter Universal PCI Card With 8-Ch Isolated Digital I/O
PCI-1784U
-
Four 32-bit up/down countersSingle ended or differential inputsPulse/direction and up/down counterx1, x2, x4 counts for each encoder cycleMultiple interrupt sources for precision application4-stage digital filter with selectable sampling rateOn-board 8-bit timer with wide range time-base selectorOptically isolated up to 2,500 VDC4 isolated digital input4 isolated digital outputBoardID™ switch
-
Product
32-Ch TTL And 32-Ch Isolated Digital I/O PCIE Card
PCIE-1730
Isolated Digital I/O Card
32-ch isolated DI/O (16-ch digital input, 16-ch digital output)32-ch TTL DI/O (16-ch digital input,16-ch digital output)High output driving capacityInterrupt handling capability2 x 20-pin connectors for isolated DI/O channels and 2 for TTL DI/O channelsD-type connector for isolated input and output channelsHigh-voltage isolation on output channels (2,500 VDC)
-
Product
Digital I / O modules
-
The 34950A module has 64-bit bi-directional lines and can be configured with 8 8-bit digital I / O channels with handshaking capability. Each 8-bit channel has programmable polarity and a threshold of up to 5V. The memory can be used to generate or capture digital patterns up to 10 MHz. It provides seven configurable handshaking protocols for a wide range of applications. In addition, two counter / totalizer channels can be used to compute events, frequency, period, duty cycle, accumulation, and pulse width.
-
Product
PCI Express Digital I/O Boards
PEX-P8R8I
-
PCI Express Board with 8 Isolated Digital Inputs and 8 Relay Outputs. Includes one CA-4002 D-Sub connector and Software Development Kit with Demo Programs
-
Product
PCI Digital I/O Boards
PISO-813U/S
-
The PISO-813U/S card is the new generation product that ICP DAS provides to meet RoHS compliance requirement. The new The PISO-813U/S card is designed as a drop-in replacement for the PISO-813, and users can replace the PISO-813 by the The PISO-813U/S directly without software/driver modification.
-
Product
48 Optocoupled Digital Inputs
YAV90321
Digital I/O
Input Voltage 3…42Vdc Isolated Inputs / Control >1000Vdc CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
Product
ISA Isolated Digital I/O Boards
ISO-P32C32
-
The ISO-P32C32 is a 64-channel isolated digital input board, arranged into four isolated banks. Each input chanel use a photo-coupler input which allows either internal power supply or external power selected by a jumper. Isolated input channels 0 ~15 are designed into group A, channels 16~31 into group B, Isolated input channels 32~47 are into group A, channels 48~63 are into group B. The power supply of the input port may use the external power or the the power from the PC side using DC to DC converter. The board interfaces to field logic signals, which eliminates ground-loop problems and isolates the host computer from damaging voltages. The ISO-P32C32 has one 37-pin D-sub connector and one 40-pin header. Users can connect the digital signal through the second D-sub connector. Each D-sub connector contains 16 input channels and 16 output channels.
-
Product
PXI 32 Channel Switch Simulation Module
40-480-221
Digital I/O
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
Digital I/O Card
-
Axiomtek's digital I/O cards feature TTL I/O, isolated I/O, relay output, and timer/counter, and supports high-density on a single board, making them specifically suitable for factory automation, industrial ON/OFF control and switch status sensing.
-
Product
16-Ch Universal Digital I/O Module
ADAM-5050
-
Digital input: Support Dry/Wet ContactDigital output: Open Collector to 30 V, 450 mW max. loadI/O Type: bit-wise selectable by DIP switchPower consumption: 0.35 W (typical); 1.2 W (max)Channels: 16
-
Product
16-Ch Source-Type Digital Output EtherCAT Slice IO Module
AMAX-5057SO
Digital I/O Module
Channels:16 (Source Type)Voltage Rating:10~30VDCRated Current Output:0.5A per channel atsignal "1"Leakage Current:10 μA per channel atsignal "0"Output Delay:From logic level 0 to 1:150μs; From logic level 1 to 0: 2ms
-
Product
PCI Express Digital I/O Boards
PCI-P8R8
-
PCI Board with 8 Channels of Isolated Digital Input and 8 Relay Outputs. Includes one CA-4002 D-Sub connector
-
Product
USB-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA, USB Digital I/O Device
779975-01
Digital I/O
The USB-6509 is an industrial, bus-powered USB device that can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is … required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the USB-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PXI High Density Digital I/O Module, 32-bit TTL
40-410-001
Digital I/O
The 40-410 range of Digital I/O Modules are suitable for operating external devices, such as heavy duty relays (power, RF and high voltage types), solenoids, lamps, or for interfacing with external logic such as a programmable instrument with a BCD interface.
-
Product
PXIe-6536, 32-Channel, 25 MHz, 100 MB/s PXI Digital I/O Module
779988-01
Digital I/O
32-Channel, 25 MHz, 100 MB/s PXI Digital I/O Module—The PXIe‑6536 can continuously stream data over the PXI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
6U PXI Multi-Channel Analog I/O PXI Card
GX3348 Series
Digital I/O
The GX3348 is a multi-channel analog I/O 6U PXI card which provides (3) programmable sources, a ground source connection, a pulse / square wave generator (A version only) and a 4 x 48 or 4 x 64 matrix - allowing the user to route the 3 sources, or ground to any of the 48 or 64 I/O channels. In addition, each I/O channel can be connected to a 16-bit A to D converter, providing DC voltage measurement capability for each channel. The module also offers (8) static digital I/O for controlling / monitoring a UUT's digital signals.
-
Product
12DI/6DO IoT Modbus/SNMP/MQTT Ethernet Remote I/O
ADAM-6050
Isolated Digital I/O Module
12ch digital input(counter)/6ch digital output(pulse output)Protocols:MQTT(TLS),SNMP,Modbus TCP,RESTful API,ASCIIGCL to perform basic logic control rulesPeer-to-Peer function to map I/O statusCloud access: Data update to AzureBuilt-in web serverWatchdog timer to recover the system
-
Product
Digital Channel, 10 MΩ Input, ±25 V, 8 Channel
CX1152A
Digital I/O Adapter
The CX1152A Digital Channel provides 8-channel digital trigger for the CX3300 Device Current Analyzer series, which is useful when a low power device with digital I/Os is evaluated. Only the CX3324A mainframe has the interface of this product. The input impedance of each channel is 10 MΩ in order to minimize the load current from the digital channel.
-
Product
10-CH General-Purpose Timers/Counters & 8-CH Digital I/O Card
PCI-8554
Digital I/O Module
- Supports a 32-bit 5 V PCI bus- On-board four 82C54 programmable timer/counter chips- 10-CH independent 16-bit down counters- 1-CH 32-bit cascaded timer- Four programmable clock sources for each timer/counter
-
Product
16-bit, 100KHz, 8SE/4DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, all isolated
CPCI-3120-8-4
-
Input range:- ± 10 V, 0-10 V software programmable- 0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V,- ± 1 V (gain)- 0-20 mA (option)- software-programmable amplifier:- PGA x1, x2, x5, x10- Conversion triggered through software,scan, timer, external event- Onboard FIFO buffering for 256 analog values- Data exchange through 16-bit I/O or 32-bit memory (PCI DMA)- Sequence RAM- Overvoltage protection- input filter: 160 kHz
-
Product
IDoor Module: 24-Channels Isolated Digital I/O With Counter MPCIe, DB37
PCM-27D24DI
Card Storage Module
Meets Advantech Standard iDoor TechnologyPCI Express® Mini Card Specification Revision 1.2 compliantSupports wide-input/output voltage (10-30 VDC/5-30 VDC)High over-voltage-protection (70 VDC) and voltage isolation (2,500 VDC)Easy configuration & efficient programming by Advantech DAQNaviI/O address automatically assigned by PCIe plug & playKeeps the output settings and values after system hot resetSupports Embedded Automation PC UNO-2200/2300/2400 seriesSupports Control DIN-Rail PC UNO-1300/1400 seriesSupports Control Cabinet PC UNO-3200/3300/3400 seriesSupports Control Panel Computers TPC-xx81/xx82 seriesSupports Thin Client Panel Computers TPC-xx51 series
-
Product
Digital I/O Modules
-
Remote RS-485 data acquisition modules offer digital, counter or relay I/O with Modbus RTU for industrial facility monitoring and management.
-
Product
96-Channel Digital I/O Plug-In
1260-114
Digital I/O Board
The high channel count of the digital I/O plug-ins allows a significant portion of digital I/O to be realized in a single slot of the Adapt-a-Switch™ carrier, saving valuable VXIbus chassis space. The 1260- 114 provides 96 digital I/O channels in twelve groups of eight bits each.
-
Product
48 Optocoupled Open Drain 42V 6A Digital Outputs
YAV90048
Digital I/O
6×8 Isolated Ouput Banks Trigger IN and OUT Termic and Overcurrent protection CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
Product
LVDS Digital I/O with Virtex-6 FPGA - PCIe
Model 78610
-
Model 78610 is a member of the Cobalt® family of high-performance PCIe boards based on the Xilinx Virtex-6 FPGA. This digital I/O board provides 32 LVDS differential inputs or outputs plus LVDS clock, data valid, and data flow control on a front panel 80-pin connector. Its built-in datacapture and data generation feature offers an ideal turnkey solution as well as a platform for developing and deploying custom FPGA-processing IP.
