Magnetic Field
an force around magnets, electric current and atomic orbits.
See Also: Magnetic, Magnetic Test, Magnetic Head, Magnetic Susceptibility, Magnetic Flux, Magnetic Stripe, Magnetic Permeability, H-field, Magnetic Field Mapping, Magnetic Field Meters, Magnetic Field Probes, Magnetic Field Sensors, Magnetic Field Test, Helmholtz Coils
-
product
Continuous Magnetic Measurement Equipment
CWM
The automatic measurement equipment to continuously measure magnetic property in commercial power frequency of magnetic steel sheet sample on line, is used for quality control. Core loss in definite time of magnetic flux density [B] or magnetic flux density [B] in definite time of strength of magnetic field [H] for excited magnetic steel sheet is measured on line.
-
product
MP field sources calibration set
The MP field source calibration set is used to measure electric or magnetic fields in a frequency range up to 3 GHz. RF fields or transient fields can be measured. The MP field source calibration set is used to check fields of the Langer EMV-Technik GmbH field sources, fields of TEM cells and IC striplines.
-
product
Special Magnetic Measuring Instrument
This is the new system of magnetization measurement equipment to continuously measure the magnetization curves of a large number of samples with once magnetic field sweep.
-
product
Turbine Flow Meters
Axial turbine flow meters are designed with wear resistant internal components to provide trouble-free operation and a long service life. Fluid entering the flow meter is first conditioned by the inlet flow straightener which reduces turbulence in the fluid. The moving fluid causes the rotor to spin at a speed that is proportional to its flow rate. As the turbine blades on the rotor pass through the magnetic field of the pickup, an electronic pulse is generated.
-
product
Power Inductor
Is a passive two-terminal electrical component that stores energy in a magnetic field when electric current flows through it.
-
product
Probes, Magnetic Field
EM-6882 | 20 MHz To 230 MHz
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
product
Magnetic Field And Permeability Measurement
MAGNETOMAT 1.790
Foerster Instruments, Incorporated
The MAGNETOMAT 1.790 is a measuring system for the precision detection of magnetic flux density and relative permeability. The MAGNETOMAT software is used for displaying the measured values and saving and exporting data. The wide range of probes facilitates optimal adjustment to the conditions of the application, such as the measurement of relative permeability within the scope of the quality control of stainless steel and low-permeable (non-magnetic) alloys. Further applications include the long-term monitoring of the magnetic environment, e.g. prior to installing magnetically sensitive devices, and the localization of ferrite enclosures in stainless steel and NE materials. Changes in material (sulfidation, degradation of lamination, structural changes) can also be proven thanks to permeability comparative measurements.
-
product
Digital Geological Data Collector
TECTRONIC
F. W. Breithaupt & Sohn GmbH & Co.KG
*Measurement and reading of azimuth of dip and angle of dip in one single operation (according to Clar method)*LCD display and memory for approx. 4.000 measurements*RS232 interface*Display indication 1° (360°, 400g, 6400– or 6300– selectable)*Many additional functions like measurement of magnetic field intensity)*Circular spirit level*Accessories upon request (Software, tripods, battery packs, …)
-
product
3 AXIS DIGITAL ELF 50/60Hz AC GAUSSMETER, FWBELL
4100 Series
Integrity Design and Reseach Corp.
Typical Applications include checking the 50 and 60 Hz magnetic fields (EMF) produced by equipments such as AC Power Lines, Office Equipment, Video Display Terminals, Household Appliances, home and Building Inspection, etc.. Magnetic fields are invisible radiations, the best method to measure the strength fields is to use one of the accurate gauss meters offer by Integrity Design & Research corp.
-
product
Hand Held Needle Detector
UI-G60
Hand held needle detector, using the principle of magnetic field, can accurately detect the specific location of ferromagnetic metal impurities such as broken needles, which is very suitable for the inspection of thin and small items. It is also suitable for the detection of large needle detectors. It can accurately find the position of steel needles or ferromagnetic metals in a small range with this hand-held needle detector, avoiding the damage of metal impurities to consumers and manufacturers, and improving the quality of enterprise products.
-
product
Fluxgate 150A Current Sensor
LF03
Our LF03 current sensor works with the dynamic Fluxgate measurement technology. It is characterized by its simple, practical design and prevents high temperature drifts. Fluxgate technology uses the phenomenon of magnetic saturation to modulate the measured magnetic field and convert it into an electric field.
-
product
Near Field Probes 30 MHz up to 3 GHz
RF6 set
The RF6 near field probe set consists of 2 passive magnetic field probes and 2 passive E field probes for measurements in the development phase of the E-field and magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF6 set allow a step by step localization of interference sources of the RF magnetic field and RF-E-field on an assembly. From a larger distance the electromagnetic interference is detected by RF-R 50-1 for the magnetic field and by RF-E 02 for the E-field. The RF-B 3-2 and RF-E 10 probes with their higher resolution can more presicely detect the interference sources of the magnetic field and the E-field. Field orientation and field distribution on an electronic assembly can be detected by special guidiance of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
product
Digital Arrester Tester
ALCL-80X
MULTI MEASURING INSTRUMENTS Co., Ltd.
・The least influence from the external magnetic field and noise by shielding for CT.・Compliant with IEC6099-5.・Measurement value can be kept in the our cloud server through our APP "M-Tracer".・Enabled the measurement for minimum 0.1μA resolution and harmonics current.・In addition to measured values, location registration by GPS, temperature, date and time can also be saved.INQUIRY
-
product
Miniature Fluxgate Magnetometer
WFG-140
The WFG-140 magnetometer is a complete 3 Axis Fluxgate Magnetometer system packaged in a rectangular package of dimensions 1.5\"x1.5\"x4.65\". With low noise and small size, the instrument can be used wherever small magnetic fields (3 x 10-7 to 1 Gauss) need to be measured.
-
product
Magnetic & Current Sensors
From the International Space Station to a simple electronic compass, we can provide a solution to meet your magnetic semiconductor needs. The F.W. Bell® product line was founded in 1944. Since then we have been a pioneer in developing instrumentation to measure electric current and magnetic fields.
-
product
Magnet Testing
Helmholtz Coils
A coil arrangement consisting of two coils with the same radius or edge length is called a Helmholtz coil. At the correct distance, these coils are arranged in parallel on the same axis and current flows through them in the same direction. Their magnetic field is then characterized by a large homogeneous area in the center of the coil, which is freely accessible for experiments and measurement tasks. Helmholtz coils can have a circular or square geometric shape.
-
product
Near Field Probes 30 MHz up to 3 GHz
RF2 set
The RF2 near field probe set consists of 4 passive near field probes for measurements in the development phase of the magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF2 set allow the step by step localization of interference sources of the RF magnetic field on assemblies. From greater distances the electromagnetic interference can be detected by RF-R 400-1 and RF-R 50-1 probes. The RF-B 3-2 and RF-U 5-2 probes with their higher resolution can more precisely detect the interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
product
Magnetic System
NMR-EA300 System
The NMR-EA300 system is the reference for calibrating magnetic sensors. It allows to generate an absolute magnetic field at <±10mG (0.1 uT) without temperature drift (<0.1ppm/C°) over a range from 14mT to 3T. This system is composed of an EA300 electromagnet with NMR poles, a MPU-16U ±150A ±70V current source of class 1ppm and a NMR20 Teslameter with a magnetic field controller (FR020).A thermostat chamber can be installed in the air gap (Optionally available on 50mm and 70mm gap poles).
-
product
Reference Magnets
Series MT
The reasonably priced WUNTRONIC standard reference magnets offer the possibility in a simple way of being able to calibrate or to check magnet measuring instruments like Gauss Meter/Tesla Meter with the respectively accompanying probes in a defined magnetic field.
-
product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-110
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Suitable for low current measurements of terminal feeder.*High sensitivity and least affection from external magnetic field.
-
product
Antenna, Loop
EM-6879 | 10 KHz – 30 MHz
The EM-6879 Loop Antenna is used for magnetic field measurements over the frequency range of 10 kHz to 30 MHz. The EM-6879 is designed for use with any 50 ohm Receiver System. The antenna has a balanced Faraday shield that reduces its response to electric fields to a vanishingly small amount so that it can produce a practically pure magnetic field response.
-
product
Capacitance Sensors
Accumeasure Series
The Accumeasure product line features capacitive sensor products for high resolution gap and displacement measurements that require a high level of accuracy that is both stable and repeatable. A capacitive sensing system consists of a probe and amplifier. Capacitive measurements can be performed in a multitude of environments using non-contact passive capacitance probes that are not affected by magnet fields, temperature, humidity, nuclear radiation, and pressure. This is largely due to the nature of the rugged and passive capacitance probes.
-
product
Overview Teslameter Gaussmeter And Magnetometers
The field strength measuring instruments are ideally suited for measuring magnetic field strength but also for residual magnetism (remanece) and determination after demagnetization of metals.
-
product
Loop Antennas
A.H. Systems' designs, manufactures and delivers high performance Loop Antennas for a wide range of magnetic field testing. Whether used in a set to measure shielding effectiveness per MIL-STD 285 and NSA 65-6 or individually to satisfy specific requirements,
-
product
NMR Precision Teslameter
PT2026
Nuclear Magnetic Resonance is the most precise technology to measure magnetic fields, and the PT2026 is the most precise NMR magnetometer on the market. In optimal conditions, it achieves a precision of under ten parts per billion! But precision is just one of the features brought by the PT2026: high fields, robustness to inhomogeneous fields, 33 Hz measurement speed, improved search time – the list goes on. The key is an instrument design, using modern RF and computer technology. The result is an NMR magnetometer that opens up a host of new application areas. Magnetometer Gaussmeter
-
product
Eddy Current Electric Conductivity Meter
Measures the conductivity of a solution by measuring the alternating magnetic field generated by the solution.
-
product
Magnetic Field Tester
MS-440
This device recognises fast and simply magnetic fields generated by electric reels and permanent magnets.
-
product
Neutron Scattering and Beamline Systems
For optical, neutron and particle beam experiments, Cryogenic offers a range of split pair magnets. These allow strong magnetic fields to be produced in a small volume with maximum access to the working space. Split pair coils can be mounted to provide either a vertical field with horizontal access or a horizontal field offering horizontal or vertical access.
-
product
High-Dynamics PIMag Linear Stage
V-522 • V-524 • V-528
Physik Instrumente GmbH & Co. KG
Reference-class linear stage. Linear positioning stages with magnetic direct drives largely dispense with mechanical components in the drivetrain and the drive force acts directly on the motion platform. Together with precision bearings, a high travel accuracy and longer lifetime is achieved. The linear positioning stages are particularly suitable for scanning applications. PIMag® Voice Coil. Voice coil drives consist of 2 essential components: A permanent magnet and a coil, which is located in the air gap of the magnetic field. When current flows through the coil, it moves in the magnetic field of the permanent magnet. The direction of motion depends on the polarity. Thanks to their low weight and friction-free drive principle, voice coil drives are particularly suitable for applications, which require high dynamics and high velocities at limited travel ranges. High scan frequencies and precision positioning are also possible with these drives, because they are free of the effects of hysteresis.
-
product
Sensitivity Testing
Response Dynamics Vibration Engineering, Inc.
Sensitivity testing involves making predictions of system response to environmental disturbance. The significance and importance of the system sensitivity estimates is very often overlooked. This gets companies in trouble and is one of the top reasons why we are called upon to provide timely solutions. Most teams are focused on getting their product to work and get it out the door. An engineering team will often not know how to quantify what to expect in the customer environment and how to test for those expected disturbances. We design hundreds of sensitivity tests and can explain the important concepts to consider in designing the tests and making the right measurements that allow for sound estimates of system response. This is an important expertise we use in our vibration, acoustic and magnetic field consulting services.
