CCTV Testers
See Also: CCTV
-
product
Build Your Hydrostatic Tester
Start with the basic Model 9901 hydrostatic tester as shown to the left with the following standard equipment:- Hydrostatic test pump, air operated.- 1% ANSI B40.1 Grade 1A stainless steel high pressure gauge.- ANSI B40.1 Grade B air pressure gauge.- Micro adjust precision regulator.- High pressure isolation shutoff valve.- Automatic lubricator.- Stainless steel high pressure manifold.- 1/4" NPT accessory port.- Bleed valve.- Air shutoff valve.- Factory set air pressure relief valve.- 7/16-20 straight thread O-ring boss outlet port (MS33649-04) with -4 male adapter fitting.- 3/4" swivel female hose inlet with strainer.- Stainless steel base plate with rubber feet.
-
product
Battery Charge and Discharge Tester
HTCFD / 790
Wuhan Huatian Electric Power Automation Co., Ltd.
The voltage monitoring information of single battery is simple, safe and accurate with wireless relay access.
-
product
Battery Load Tester
MD4260
Test capabilities: Battery voltage, battery cranking, battery charging volts and good/bad battery test. Test batteries on and off the car in just 30 seconds. Heavy duty copper-plated clamps. Internal loaded unit with a 100-amp load capacity. Load safety switch to prevent arcing. For 6- and 12-volt batteries.
-
product
Pitot Static Tester
ADSE 746
The ADSE 746 caters fully for all aircraft types and the different electrical power supplies. It can be used for testing high performance civil and military aircraft, fixed and rotary wing. Themulti-pressure outlets option can suit themore complex pilot-staticsystems.This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems. The large touch screen display, with on-screen help, enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator. The test set is robust and housed in a mobile weatherproof case fitted with tire wheels. An attached bag contains the pressure hoses and electrical cables.
-
product
Battery Testers
Shanghai Beha Electronics Co., Ltd.
*can measure the resistance of rechargeable batteries and DC voltage.*can also test Ni-cd, Ni-MH, Li-ion batteries.*DC Voltage measurement.*4-wire resistance measurement.
-
product
Button Impact Tester
TESTEX Testing Equipment Systems Ltd.
Button Impact Tester, to determine the impact resistance of plastic sew-through flange buttons to a falling mass of 0.84kg (29.5oz), released from a height of 67mm (2.625 inches) or other heights as required. Cracking, chipping or breakage constitutes failure.
-
product
Hardness Testers
The hardness tester products you will find at PCE Instruments (PCE) are used for determining surface hardness. Each hardness tester uses a standard method of measurement. The measuring principles of most hardness tester devices are based on either the penetration of a diamond indentor into the material being tested or a calculation related to the force of the rebound after striking the tested material. However, material hardness can also be measured accurately through ultrasonic testing. Each hardness testing method has its benefits and will allow for the precise measurement of material hardness in accordance with the technical specifications of the hardness testing instrument.
-
product
Cable and Harness Tester
CHT
The Cable and Harness Tester (CHT) provides multiple testing capabilities for up to 300 connector/harness test points. Test capabilities include DC Insulation Resistance (IR), DC and AC Dielectric Withstanding Voltage (DWV), and 2-Wire and 4-Wire Continuity.
-
product
Battery Discharger & Capacity Tester
IDCE-2415CT
Fuzhou Fuguang Electronics Co., Ltd.
IDCE-2415CT Battery Discharger & Capacity Tester
-
product
Brinell Hardness Tester
KB Series
Newage Testing Instruments, Inc.
The Newage KB Series is a popular, manually-controlled Brinell hardness tester that meets ASTM E-110. This lightweight, portable tester is ideal for virtually any size or shape of metal specimen.
-
product
Turns Ratio Testers
TRT Advanced Series
TRT Advanced series is the newest DV Power solution for transformer turns ratio measurement. Besides its main application, each turns ratio tester from this series also measures transformer excitation current and phase shift. Furthermore, all models perform automatic vector group detection and magnetic balance on three-phase transformers and three-phase autotransformers. They have a built-in true three-phase power source. For that reason, they can test transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.The instruments can output test voltages from 1 V AC to 500 V AC, depending on the model. With the highest test voltage 500 V AC, TRT500 provides the most accurate turns ratio testing of power transformers used in power generation and transmission. The output test voltage of TRT500 can be boosted to 5 kV AC using the external CVT20 extension transformer. This application is specially designed for testing turns ratio of capacitive voltage transformers. The other three models, TRT400, TRT250, and TRT100 can output up to 400 V, 250 V, and 170 V respectively. The low test voltage of 1 V AC enables turns ratio verification of current transformers.TRT500 is equipped with a large 10.1” graphical touch screen display. Other models, (TRT400, TRT250, TRT100) have 7” graphical touch screen display. Besides making the interface much more user-friendly compared to older turns ratio testers, it also brings certain options that were previously available only with DV-Win software. The most important are test templates and automatic test mode. Users can simply create test templates, store them in the instrument’s memory, and load when in the field with just a few clicks.This turns ratio test set, as well as all other DV Power turns ratio testers, has a built-in tap changer control unit. It enables remote control of an on-load tap changer (OLTC) directly from the instrument. In order to make the most out of this feature, the instrument can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions, and saving results. This option, especially in combination with test templates, significantly facilitates and shortens the turns ratio testing time. Automatic test mode minimizes human errors, which makes the measurement more reliable.
-
product
Hand-Held/Digital Load Tester
6030
• Full 125 Amp load tests 12 Volt batteries, alternators and starters on all type of vehicles• PATENTED• Made in USA of US and Global Components
-
product
Voltage, Continuity & Current Tester
T5-1000
Measure current up to 100 A without breaking the circuit with OpenJaw™ design. The T5-1000 Electrical Tester is a versatile troubleshooting tool to carry to every job site. Use it to check voltage, continuity, and current–all with one compact tool.
-
product
Loop / PFC Testers
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2715 is a loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
product
Digital RCD Tester
1113 EL
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Very low consumption.● 50Hz and 60Hz operation.● Accurate digital readout of disconnection time.● Over temperature protection.● Over voltage protection.● Fuse protection.● Zero crossing circuitry permit testing at 0° or 180°.● Auto power off. ● Backlight function. ● Wiring polarity indicator.● Measure voltage between Line and Earth before testing.● Frequency measurement indication.
-
product
Ink Rub Tester
RT-01
Ink Rub tester, also known as abrasion resistance tester, using ASTM D5264 and is designed to measure the ink resistance against rubbing on packaging materials. RT-01 Ink Rub Tester is designed for the abrasion resistance of surface coating layers of printed materials, such as ink layer or photosensitive coating.
-
product
Standard Brinell Hardness Tester
BRIN400 Series
The Standard Brinell Hardness Tester - BRIN400 Series of closed loop Brinell hardness testers represent the latest in Brinell hardness testing technology. They are robust, reliable, proven and designed to meet a customer’s most demanding requirements in harsh industrial environments such as those found in foundries, forges and steelworks.
-
product
Bare Board Tester
1232
High-Precision Batch Fixture-Type Testing System that Support Boards with Embedded Passive and Active Devices. The 1232 is a bare board tester that utilizes the full range of Hioki’s in-circuit testing technologies to deliver LSI reliability testing, complex component separation testing, high continuity and insulation testing, and more. (Double-sided alignment) Testable board dimensions: 50 × 50 to 330 × 330 mm (including clamp area) • Support for build-up boards that require resistance guarantees.
-
product
Horizontal Flammability Tester
Sataton Instruments Technology CO., Ltd
Horizontal flame resistance tester is design based on FMVSS 302 to determine the burning behavior of materials as interior in motor vehicles by calculating the burning rate of the specimen after ignition by a small flame. Exposed to a certain flame for specified time, the specimen which is clamped in a U shape holder will be measured for the burned distance and time taken to burn this distance. The tester is particularly important for assessing safety of the materials used in the passenger compartment.
-
product
Anaerobic Jar Tester
LD-LAJ-A12
Anaerobic JarLD-LAJ-A12with 3.5 L capacity has PMMA transparent, smooth surface jar design. High quality O-ring is used to make tight sealing between jar and lid. Adopted with quick snap-shut coupling, enables quick connection to the system in a one soft move. The number of gas packs needed may vary in brands and pack size, required to create anaerobic condition in the jar.
-
product
Load Stability Tester
TruMotion™ Acceleration
When transport vehicles accelerate, turn or brake, the resulting low-frequency accelerations can cause unit loads to shift. Due to both safety issues and potential product damage/waste, regulatory bodies are requiring testing that’s closer to reality – assuring safe and stable unit load integrity!
-
product
Earth Resistance Testers
Shanghai Beha Electronics Co., Ltd.
A handy test and measurement instrument for testing Earth resistance and Soil resistivity.
-
product
Current Transformer Tester
HTCT-300
Full-featured, can not only satisfy various CT (eg: protection, measurement and TP category) but also PT type electromagnetic unit for its excitation characteristics (ie voltage current characteristics), ratio, polarity, secondary winding resistance, secondary load, ratio deviation, angle deviation and other test requirements.
-
product
Wireless Connectivity Tester
CMW270
The R&S®CMW270 is the ideal test solution for integrated wireless communications solutions as used in laptops, netbooks, game consoles, data cards, wireless headsets and other products of the IoT market. Within the R&S®CMW500 - Production Test product family, the R&S®CMW270 offers functionality tailored to the above applications. The tester provides network emulation (signaling mode) for WLAN and Bluetooth® as well as generator and analyzer functionality for standards such as WLAN, Bluetooth®, GNSS and broadcast technologies.
-
product
Battery Testers
Memory & Read FunctionRight Device to know the TRUE -LIFE of Battery Capacity (Resistive / Voltage) Simultaneously MeasureOn - Line Testing without shutting down batteryBuilt - in Comparator FunctionRates Conditions as PASS, WARNING or FAILDatalogging Memory FunctionCompact and lightweightRS-232 Interface & SoftwareAuto Power Off
-
product
Network & Cable Testers
Detects PoE end/mid-span voltages on network cables. LED indicators instantly show “GO/NO-GO” detection on PoE networks. Plug cables directly into the builtin RJ45 jack or use the included patch card to detect voltage in wall jacks.
-
product
30KV-100KV AC/DC Hipot Tester
2674
Shenzhen Chuangxin Instruments Co., Ltd.
30KV-100KV AC/DC Hipot Tester
-
product
4-Wire Universal Cable/Harness Tester
LX-850
Shenzhen Lian Xin Technology Co., Ltd.
Starting up conducts self-diagnosis and self-correction·The system can scan and direct automatically.·The system provides advanced instant open-circuit, short-circuit, continuity test, can test the wire break·It can function as unilateral, standard, multi-segment and spot test of wire·The maximum test voltage is AC1000V / DC1500V·The system adopts the advanced four-wire measurement, and the minimum measurable range is 1mΩ.·The maximum test spot is 256.·640×480 full Chinese/English large color display .·All varieties of linearity and safety tests are available.·Fully programmable continuous test is available.





























