Pulse Generators
Produce single or multiple volatage pulses for device verification and fault detection.
See Also: Pulse, Pulsers, Pulse Width, High Power Pulse Generators, High Voltage Pulse Generators, Programmable Pulse Generators
-
Product
CAMAC Multifunctional Logic Unit
CMDGG8
-
The CMDGG-8 is a multi functional FPGA based delay, logic and timing module which provide often needed functions such as gate, delay & pulse generator, logic fan in / fan out, coincidence register and scaler / pre-scaler.
-
Product
cDAQ-9191, 1‑Slot, Ethernet and 802.11 Wi‑Fi CompactDAQ Chassis
781497-01
Chassis
1‑Slot, Ethernet and 802.11 Wi‑Fi CompactDAQ Chassis - The cDAQ‑9191 is a Wi‑Fi chassis designed for small, remote, or distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. You can send data from the cDAQ‑9191 to a host PC over Ethernet or IEEE 802.11 Wi‑Fi. The chassis also has four 32‑bit general‑purpose counters/timers built in. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
Pulse generator
9355-1
-
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
Product
Electrical Signal Test
-
High-density, multi-channel pulse pattern generators and bit error detectors for the design, characterization and production test of optical transceivers and opto-electrical components.
-
Product
RF Signal Generators
-
As Rigol's RF first signal source, the DSG3000 series offers standard AM/FM/ØM analog modulation, as well as options for I/Q modulation and I/Q baseband output. The instrument is available with maximum frequencies of either 3 GHz or 6 GHz. Featuring a high signal purity with phase noise measuring <-110dBc/Hz@20kHz (typical) and a wide output range of -130dBm to +13dBm, the DSG3000 RF signal generator has standard pulse modulation with an on/off ratio of up to 80dB, with optional pulse train generator available. The DSG3000 series also has an amplitude accuracy of <0.5dB (typical).
-
Product
200 MS/s Waveform Generator & Dual 50 MHz Pulse/ Timing Generator
3172
Pulse Generator
The Racal Instruments™ 3172, a 200 MS/s Waveform Generator and Dual 50 MHz Pulse and Timing Generator, combines multi-instrument density and highfrequency performance in a single-slot, C-sized VXIbus format.Waveform output in the range of 100 μHz to 30 MHz with 16-bit vertical resolution (12-bit vertical for 3171 emulation) and pulse output to 50 MHz make the 3172 a powerful solution to a variety of test stimulus requirements.
-
Product
High Voltage 50 Ω Pulse Generator
TLP-8010C
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Combines TLP-8010A and TLP-4010C into one system*Can be operated together with TLP-8012A5 and TLP-3011C pulse width extenders*Ultra fast 50 Ω high voltage pulse output with typical rise time 100 ps (0-40 A) and 300 ps (> 40 A)*Up to 80 kW peak output power into 50 Ω load*Built-in HMM pulse up to ±15 kV with 50 Ω configuration*High pulse output current up to ±80 A (short circuit) with minimum 6 dB reflection suppression*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 GPIB programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns (0-40 A), 1 built-in pulse width: 100 ns (> 40 A)*The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0-40 A)*Optional external pulse width extensions from 5 ns to 500 ns (> 40…80 A) using the external pulse width extender TLP-8012A5*Built-in pulse reflection suppression*Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurements of complete wafers*High performance and high quality components
-
Product
PCI Digital IO Board
-
*Bus Interface: PCI Bus*Counter/Timer: 16 Channels*Counter Size: 32 bit*Max. Source Frequency: 80MHz*Compatibility: 5 V TTL/CMOS*Discrete Inputs: 24 Channels*Discrete Outputs: 24 Channels*Pulse Generation: 12 Channels*Bi directional I/O's: 8 Channels*Oscillator stability: 50 ppm*Op-to isolation for I/O's*DMA buffered operation*16-bit data bus 32 bit Address bus for External Memory Interface*The Pulse Width and PRI of the pulses can be varied*The pulse generation frequency from 10Hz to 40MHz (25ns to 100msec)*The no. of pulses controlled from 1 to 255 pulses*All the pulse input and the output signals and Bi-directional write signals driven through Pin Driver*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
PCI-6601, 5 V, 4-Channel Counter/Timer Device
777918-01
Digital I/O Module
The PCI‑6601 performs encoder position measurements, event counting, period measurements, pulse-width measurements, pulse generation, pulse-train generation, and frequency measurement. It features four counter/timers, digital debouncing … filters, and TTL/CMOS-compatible digital I/O. The PCI‑6601 can perform one high-speed DMA transfer.
-
Product
Function/Arb. Waveform Generator
-
Qingdao Hantek Electronic Co., Ltd.
multi-function like arbitrary waveform generator, pulse generator, 16-bit word generator, 7-digit cymometer and function generator; It can generate and output stable, accurate and low distortion signals; Built-in over 150 type arbitrary waveforms, which is easy to simulate various signals; Its large screen, user-friendly interface design and keyboard layout are convenient to use; Rich standard configuration interfaces easily achieve remote control of the instrument.
-
Product
Basic Function Generators
-
PeakTech Prüf- und Messtechnik GmbH
Which can be used as a signal generator, but also as a pulse generator. Direct digital synthesis (DDS) enables the function generator to generate various periodic signal curves with high precision.
-
Product
Pulse Start Generator for High Pressure Sodium Lamp
LPSG60662
-
The start-up test of the special lights pulse start generator is for lighting class industry such as high pressure sodium, it is according to IEC60662: 2011 and GB/T13259-2005 standard requirements.
-
Product
cDAQ-9171, 1‑Slot, USB CompactDAQ Chassis
781425-01
Chassis
1‑Slot, USB CompactDAQ Chassis - The cDAQ‑9171 is a bus‑powered, CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9171 also has four 32‑bit general-purpose counters/timers that you can access through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
cDAQ-9184, 4‑Slot, Ethernet CompactDAQ Chassis
782069-01
Chassis
4‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9184 is a CompactDAQ Ethernet chassis designed for small, remote, or distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use a combination of modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers built in. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement. With multiple timing engines, you can run seven hardware‑timed operations simultaneously, with three independent rates for analog input.
-
Product
cDAQ-9188 , 8‑Slot, Ethernet CompactDAQ Chassis
782824-01
Chassis
8‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9188 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this … chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
Test Solution Offering BER Testing
Eye-BERT Micro LR
-
The Eye-BERT Micro LR is a low cost, easy to use test solution offering BER testing at any rate between 6.312 and 125Mbps on either optical or electrical interfaces. Features include: continuously variable bit rate, user programmable pulse generator, internal CDR with retimer mode, bit rate measurement, and recovered clock output. The Unit is supplied with anti-skid bumpers for bench use, and is small enough to be integrated into larger systems for dedicated link verification.
-
Product
4/8 Channel 1.0 ~ 30.0 Gb/s Pulse Pattern Generator and Error Detector
CA9808C
-
The UC INSTRUEMNTS CA9808C 4/8 Channel 1.0 ~ 30.0 Gb/s pulse pattern generator and error detector is a high performance, flexible and cost effective four channel Pulse Pattern Generator and Error Detector that can operate from 1.0 Gb/s to 30.0 Gb/s each Channel. 4/8 channel 30.0 Gb/s make it total up to over more than 120/240 Gb/s testing capacity. It is also a standalone Bit Error Rate test solution that incorporates an internal full rate clock synthesizer.
-
Product
PCIe-6612, PCI Express, 5 V, 8-Channel Counter/Timer Device
782351-01
Digital I/O Module
The PCIe‑6612 performs encoder position measurement, event counting, period measurement, pulse-width measurement, pulse generation, pulse-train generation, and frequency measurement. It features eight counter/timers, digital debouncing filters, and TTL/CMOS-compatible digital I/O. The PCIe‑6612 can perform three simultaneous high-speed DMA transfers.
-
Product
CompactDAQ Chassis
Chassis
CompactDAQ Chassis feature USB, Ethernet, or WiFi connectivity and come in multiple slot counts to provide the right amount of I/O for various applications. You use these models with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. CompactDAQ Chassis can include multiple general-purpose counters/timers that you can access through an installed, hardware-timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement. CompactDAQ Chassis also offer multiple timing engines, which allow you to run multiple hardware-timed operations simultaneously with independent rates for analog input.
-
Product
Pulse and Universal Generator
TGP3100
-
The TGP3100 Series are true pulse generators using all digital techniques. They can replicate the capabilities of traditional pulse generators whilst adding many additional facilities such as pulse modulations. GPIB (option), USB and LXI compliant LAN interfaces
-
Product
PXIe-6614, 5 V, 8-Channel, Precision Reference PXI Counter/Timer Module
782353-01
Counter/Timer Module
PXIe, 5 V, 8-Channel, Precision Reference PXI Counter/Timer Module—The PXIe‑6614 is a high-precision counter/timer module that performs encoder position measurement, event counting, period measurement, pulse-width measurement, pulse generation, pulse-train generation, and frequency measurement. It features eight counter/timers, digital debouncing filters, and TTL/CMOS‑compatible digital I/O. The PXIe‑6614 offers industrially rugged features for a wide array of applications such as automotive/aerospace, industrial/motion control, and manufacturing test. Measurements are highly accurate and precise over longer periods of time because of the oven‑controlled crystal oscillator (OCXO) in the module.
-
Product
16/32 -CH 16-Bit 250/500 KS/s Multi-Function DAQ Cards with Encoder Input
PCI-9222/9223
Data Acquisition Module
The ADLINK PCI-9222/PCI-9223 is a 16-bit, 16/32-CH, 250/500 KS/s high performance DAQ card with 8 different input ranges. It also features 2-CH 16-bit analog outputs capable of a 1 MS/s update rate, 2-CH encoder inputs, and programmable function I/O. The software-programmable function I/O supports a variety of applications, including TTL digital I/O, high-speed DIO, general-purpose timer/counter, pulse generation, and PWM output. Analog input, analog output, and function I/O at full speed simultaneously, and multiple cards can be synchronized through the SSI (System Synchronization Interface) bus if users need more channels than a single board can provide. Ideal for mixed-signal tests, laboratory research, and factory automation, PCI-9222/PCI-9223 is the best single-board solution on the market providing the best integration capability of multiple tasks with high performance and an affordable price.
-
Product
6U PXI Multi-Channel Analog I/O PXI Card
GX3348 Series
Digital I/O Module
The GX3348 is a multi-channel analog I/O 6U PXI card which provides (3) programmable sources, a ground source connection, a pulse / square wave generator (A version only) and a 4 x 48 or 4 x 64 matrix - allowing the user to route the 3 sources, or ground to any of the 48 or 64 I/O channels. In addition, each I/O channel can be connected to a 16-bit A to D converter, providing DC voltage measurement capability for each channel. The module also offers (8) static digital I/O for controlling / monitoring a UUT's digital signals.
-
Product
sbRIO-9403, Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780539-01
Digital Module
Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The sbRIO‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the sbRIO‑9403 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and other applications.
-
Product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
782401-01
Digital Module
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
Product
Basic Pulsed-RF Measurements
S93025B
-
S93025B basic pulsed-RF measurements enables 4 internal pulse generators that can be used to control the internal pulse modulators (N522xB/N524xB Options 021/022), and provides an integrated pulse application that uses the wideband-detection method.
-
Product
NI-9402, LVTTL, 4 Bidirectional Channels, 55 ns C Series Digital Module
779987-01
Digital Module
LVTTL, 4 Bidirectional Channels, 55 ns C Series Digital Module - The NI‑9402 is a per‑channel configurable digital I/O interface for input or output. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9402 for … implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
Product
Turbine Flow Meters
-
Axial turbine flow meters are designed with wear resistant internal components to provide trouble-free operation and a long service life. Fluid entering the flow meter is first conditioned by the inlet flow straightener which reduces turbulence in the fluid. The moving fluid causes the rotor to spin at a speed that is proportional to its flow rate. As the turbine blades on the rotor pass through the magnetic field of the pickup, an electronic pulse is generated.
-
Product
Digital Delay Generators
-
Highland has introduced three unique features to digital delay generation: a "Queued Updates" feature allows time settings to be changed without corrupting ongoing timings; a "Train" feature allows multiple pulses to be generated from each trigger; and a "Frames" feature allows complex delay sweeps and pulse scenarios to be pre-loaded and rapidly executed. Digital delay and pulse generators are available in 1-6 channels, with square, Gaussian, and arbitrary waveshapes, and insertion delays as low as 10 nanoseconds.
-
Product
Transient Pulse Generator
8282-1
-
The Model 8282-1 Transient Pulse Generator was designed for screen room use in making conducted spike susceptibility tests. It provides all the waveshapes required by MIL-STD-461B/C and many other military EMI specifications
