-
Product
Digital Harmonics Clamp Tester
HWT-301
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Harmonics and leakage current measurements.*Up to 25th harmonics current and voltage measurements.*True rms reading for ACA and ACV.*Data-hold and Auto power off function.*Conform to IEC safety requirements.
-
-
Product
Four-Pole Metal Oxid Varistor Surge Arrestor
PIIIM-275/3+1 Vseries
-
PIIIM-275/3+1 Vseries is a four-pole, metal oxid varistor surge arrester combined with gas discharge tube, Type 2 according to EN 61643-11 and IEC 61643-11. These arresters are recommended for use in the Lightning Protection Zones Concept at the boundaries of LPZ 1-2 (according to IEC 1312-1 and EN 62305), where they provide the equipotential bonding and discharge of the switching overvoltage, which is generated in power supply systems entering the building. The main use of PIIIM-275/3+1 Vseries arrester is in all kinds of industry, residential and administration buildings. They are to be placed into the subsidiary switchboards or control boxes.
-
Product
Clamp Sensors
-
Kyoritsu Electrical Instruments Works, Ltd.
Can measure AC current up to 1000A Flexible and light weight by the air core coil used at the sensor part Designed to meet the international safety standard IEC 61010-1 CAT IV 300V, CAT III 600V
-
Product
Reverberation Chambers
-
Over the past several decades, RCs have been enjoying growing popularity as a promising facility for the characterization of wireless devices and for EMC testing. The RC (Reverberation Chamber) measurement method exhibits much competitive superiority over the AC (Anechoic Chamber) method and TEM Cell method, such as low cost, enhanced test repeatability, a more realistic test environment, and easily achieved high-field environment. The application of the RC for performing EMC testing was first proposed by H. A. Mendes in 1968. In the recent IEC 61000-4-21 standard, the importance of EMC testing using RCs as an alternative measurement technique has been recognized.
-
Product
Manual PAT Testers
-
If you are looking for a manual PAT tester with a pass fail reading or a PAT tester with readings we have a solution for you. Carry out mains supply checks, IEC lead tests, Earth continuity tests at 200mA, Insulation resistance tests to 250V and 500V, and more with these popular testers. All of our manual PAT testers are available as kits to help you streamline the way you work.
-
Product
Coupling Decoupling Network
TBCDN-M3
-
The TBCDN-M3 is a Coupling Decoupling Network for conducted immunity testing according to IEC 61000-4-6.
-
Product
Test Package
-
Shenzhen Bonad Instrument Co., Ltd.
We can provide a variety of different specifications of freezing load test packages, including AHAMHRF-1 2007/ SASO 2664-2007 Sawdust freezing test package, AS1731.4-2003 Australian frozen Load Test Package, AS72-2005 North American Commercial Refrigeration Load Simulation Test Package, IEC 62552 Test Package for Freezing Load Testing in Refrigerators. In addition, we can also provide customization according to test requirements. For more information, please contact us, BONAD will provide you with professional technical advice and high-quality testing equipment.
-
Product
Scienlab Regenerative 3‑Phase AC Emulator
SL1200A Series
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Medical Box PC
-
ADLINK’s medical box pc, compliant with IEC 60601-1 (3.2 edition) / IEC 60601-1-2 (4.1 edition) for safety and performance of medical equipment, is designed to build in space-limited medical devices, such as C-arm and surgical navigation system. The medical grade platform features ADLINK’s MXM Graphics Module supporting NVIDIA GPU, ensuring the acceleration of image reconstruction and beamforming and moreover, significantly reducing data transmission delay, lowering latency and enhancing image quality with AI to assist doctors in detecting diseases or other abnormalities.
-
Product
Concentric Ring Set
PRF-911
-
- Measures surface resistance per ANSI/ESD STM11.11- Measures volume resistance per ANSI/ESD STM11.12- Meets the requirements of IEC 61340-2-3- Approximates surface & volume resistivity per ASTM D-257- Incorporates a spring loaded, self-aligning center electrode feature to reduce calibration frequency- Includes an insulated and metal dual test bed- Designed to work with a wide range resistance meter and one 5 lb. electrode- Certificate of calibration traceable to NIST included
-
Product
Sound Meter
4431
-
The Kanomax Sound Meter – Model 4431-1G is the world’s first 0-dB function sound meter available. It is designed to meet Type 2 standards for ANSI S1.4 1983 and IEC 61672-1. The magnetic accelerometer easily attaches to machinery for increased accuracy and precise operation.
-
Product
TDK Test Services
-
TDK Test Services offers testing to domestic and international EMC test regulations, including IEC, ISO, CISPR, and SAE. Test services are offered in our 3m semi-anechoic chamber, 3m fully-anechoic chamber, 10-meter open area test site, and our shielded conducted test chamber.
-
Product
Harmonic Filter Resistors
-
Post Glover designs, builds and tests their harmonic filter resistors in accordance with applicable IEC and IEEE standards to guarantee their performance. With no two installations ever being the same, our experienced engineers develop the proper solution for your particular application and environment. Our low inductance designs are built using all stainless steel elements in corrosion resistant enclosures chosen for your unique specification. Request a quote for your custom harmonic filter resistor.
-
Product
Powerline Analyzer
SHARK 100
-
Amperis introduces one of the highest performance panel-type billing grade meters in the industry. Based on a new platform, this low cost meter significantly outperforms other much more expensive equipment. This unit is perfect for new measurement applications and for direct and simple replacement of existing analog meters. The Shark is excellent for high accuracy energy measurement exceeding ANSI C12.20 (0.2%) and IEC 687 (0.2%) energy measurement standards.
-
Product
Protection Relay Testing
-
Haomai Electric Power Automation Co.,Ltd.
1)Embedded industrial PC with 9.7" TFT LCD screen 2)Both online and offline test available 3)Can test both universal and IEC 61850 protection relay 4)6-phase current + 6-phase voltage output 5)Provide various type of messages which conforms to IEC 61850-9-1/9-2,GOOSE, IEC 60044-7/8 FT3 6)Able to test MU and optical digital signal 7)Built-in GPS module
-
Product
Medical Computer Equipped With MXM Graphics Module Supporting NVIDIA Quadro® GPU With 8th/9th Generation Intel® Core™ I7/i5/i3 In LGA1151 Socket. Compliant With IEC 60601-1/IEC 60601-1-2
MLB-3000
Industrial Computer
- Medical grade computer compliant with IEC 60601-1:2005 + A1:2012 + A2:2020 (3.2 edition) / IEC 60601-1-2:2014 + A1:2020 (4.1 edition)- ADLINK MXM Graphics module support (Type A/B, up to 120W)- 8th/9th Gen Intel® Core™ i7/i5/i3, Celeron® processor- Dual SODIMMs for up to 64GB DDR4 non-ECC memory (dependent on CPU)- DisplayPort (2 from CPU, 4 from MXM)- 1x M.2 E key supporting 1630 or 2230 for Wi-Fi/Bluetooth module, 1x M.2 B key supporting 2242 or 2280 for SATA storage module- Reliable Molex type 12V DC-in connector- 1x Intel® i219-LM and 3x Intel® i210-AT
-
Product
LAN Router
ICR-2701WA01-S1
Router
ICR-2700-S1, EMEA, 2× ETH, USB, WiFi, Metal, ACC EU. Security based on IEC 62443-4-2 level 1. 1.3 GB eMMC storage to host customer SW applications.
-
Product
28 Days Test Bench (Single Phase & Three Phase)
-
The SCR Elektroniks 3 station MCB 28 Days and Temperature Rise Test Bench is economically designed to verify the 28 Days Test (21 hr ON, 3 hr OFF Test) as per clause 9.9 of IEC 60898-1 and Temperature Rise of the parts of a Circuit Breaker specified in Table 6 of clause 8.4.1 measured under the conditions specified in clause 9.8.2 of IEC 60898-1.
-
Product
Low Power Programmable AC Source
61600 Series
-
Chroma Systems Solutions, Inc.
Power:500VA (61601)1000VA (61602)1500VA (61603)2000VA (61604)4000VA (61605)Voltage range: 0-150V/0-300V/AutoFrequency: 15Hz 1000HzCompact size and weight attributable to advance PWM technologyBuilt-in PFC, provide input power factor over 0.98 (full load)AC+DC output mode for voltage DC offset simulationProgrammable slew rate setting for changing voltage and frequencyProgrammable voltage, current limitOne-key recall for 9 different voltage and frequencyLow output impedance for testing IEC 61000-3-2 ( 61605 )Comprehensive measurement capability, V, Irms, Ipk, Inrush, P, Q, S, PF, CF of current and etc.High output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates ON/OFFAnalog programming interface3 units combined to 3-phase power outputEasy-use software for operation and ON/OFF testOptional GPIB and RS-232C interfaceFull protection: OP,OC,OV and OT protection
-
Product
Modular I/O System
ADAM-5000 Series
-
ADAM-5000 PC-based controllers, including the ADAM I/O series system, and ADAM-5560CE/KW Micro PAC, feature an Intel Atom D510 CPU along with control specific features such as watchdog timer, battery backup RAM and deterministic I/O. ADAM-5560KW PC-based controllers support 5 standard IEC 61131-3 programming languages in CE 5.0. With the optional HMI Software and built-in VGA port, this remote I/O module can avoid using additional SCADA PC’s in their applications.
-
Product
GTEM cells
-
Meets IEC/EN 61000-4-20, SAE J1752/3, IEC 62132-2 and IEC 61967-2. The GTEM cell is, in principle, a tapered coaxial line (offset septum plate), which is terminated by a hybrid combination of discrete resistors and RF absorbers to achieve a 50 Ohm broadband match. It is applied for Measuring of Emission, Radiated, radio frequency field-immunity test.
-
Product
Battery Capacity Tester
BLU-A Series
-
The battery capacity test is performed to determine the health of a battery. DV Power’s battery load unit BLU-A is a portable, powerful, and lightweight solution for battery capacity measurement. It is applicable to any battery string such as lead-acid, Li-Ion, Ni-Cd, etc., with up to 500 V battery voltage. As a special feature, BLU100L model enables the capacity testing of a single Li-Ion cell.The capacity test is performed in an accurate and user-friendly way. Also, it is in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.Battery load unit BLU-A enables setting discharge currents up to 240 A, with a resolution 0,1 A. Furthermore, if higher currents are required, BLU-A units can be connected in parallel, or additional BXL load units can be used.The instrument offers the best power-to-weight ratio in the market. BLU-A models start from 12,8 kg / 28.2 lbs and deliver up to 28,4 kW of power.The user can select three discharge modes:Constant current,Constant power,Constant resistance.Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.The instrument monitors discharge parameters in real-time during the capacity test. A 4,3-inch touch screen display shows battery voltage, current, elapsed time, and capacity during the entire test. Also, BLU battery load unit can be used with DV-B Win software. As a result of that, a user can see a detailed numerical and graphical presentation of key parameters and can create reports in various formats.Testing with BLU-A doesn’t require a disconnection of the battery from the testing equipment.
-
Product
Explosion-Proof Gas Analyzer
51 Series
-
HORIBA’s 51 Series of explosion-proof analyzers provide safe, reliable and accurate measurements when analyzing flammable gases or operating in explosive environments. The 51 Series complies with IEC 60079. The 51 Series explosion-proof analyzers infrared allow for the measurement of CO, CO2, CH4 and other organic gases. The TCA-51 uses a thermal conductivity detector for H2 measurements and the MPA-51 and PMA-51 models integrate magneto-pneumatic and paramagnetic detectors for O2 measurements.
-
Product
CDN - Coupling / Decoupling Networks
-
The Coupling- / Decoupling Networks are used to inject common mode disturbances to Equipment under Test (EuT). Further the CDNs provide sufficient decoupling between Auxiliary Equipment (AE) and disturbance signal. The requirements for CDN and their application are described in the standard IEC 61000-4-6 (Immunity to conducted disturbances, induced by radio-frequency fields). CDNs have a common mode impedance of 150 Ohm and are available for a multitude of cable types and connectors.
-
Product
IEC60068-2-75 Impact Spring Hammer Single Energy
CX-T02
-
Shenzhen Chuangxin Instruments Co., Ltd.
Required by many Standards to test the mechanical integrity of product enclosures. After applying the impact with the hammer, the product is examined with accessibility probes to determine access to shock, energy, and injury hazards. Built in exact accordance to IEC, EN, UL, CSA and other international Standards.
-
Product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
-
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
Product
UV Chamber
-
In PV modules, many different components are exposed to the sunlight. Therefore, the IEC 61215 defines a UV preconditioning test (MQT 10) to test whether these components can withstand the UV radiation of the sun. In our test chamber, the UV radiation is up to five times the sun intensity to accelerate the test, as requested in the UV preconditioning test.
-
Product
AC / DC Current Clamp
HT9025
-
HT9025 has been designed to measure AC/DC current up to 1000A, DC voltage up to 1500V and AC voltage up to 1000V in TRMS reaching CAT IV 600V and CAT III 1000V in compliance with safety standard IEC/ EN61010-1.
-
Product
Metallic Probe Inductive Proximity Sensor
-
Shanghai Pubang Sensor Co.,Ltd.
1. All-in-one stainless steel housing design, strong anti-shock function2. Magnetic field interference, high switching frequency, wide temperature range3. Protection class IP67 (IEC)
