Filter Results By:
Products
Applications
Manufacturers
Solar Cell
Convert light to electricity.
-
product
Post-Diffusion Process Control
Suns-Voc MX
Perfect for paste-firing optimization and process control. Open-circuit method indicates the upper bound of efficiency for any solar cell precursors
-
product
Grid-Connection Testing System
This system is a power supply test system that performs grid-connection testing of distributed power sources (solar cells, fuel cells, gasoline engines, etc.)Enable inverter device testing that complies with the Agency for Natural Resources and Energy’s “Guidelines for System Interconnect Technical Requirements” and the Japan electrical Safety & Environment Technology Laboratories (JET) publication “Testing Methods for Small Solar Cell Power Generation System and System Interconnection Safety Devices”.
-
product
Saluki SEL8 Series Programmable DC Electronic Load (up to 200KW)
The new SEL8 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL8 series delivers high speed and high accuracy with a resolution of 1mV and 1mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL8 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.* Customization available upon request
-
product
Saluki SEL7 Series Programmable DC Electronic Load (up to 6kW)
The new SEL7 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL7 series delivers high speed and high accuracy with a resolution of 0.1mV and 0.01mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL7 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.
-
product
Solar Cell Simulation
Setfos
Easily calculate the short circuit current, open circuit voltage Voc and fill factor with Setfos. Tweak the layer stack and add light scattering layers for enhanced absorption. Optimize for AM1.5 or specific wavelength bandsElectrical IV curvesCurve fitting & parameter extractionAC simulation and transient experiments like photo-CELIVAdvanced device physics: SRH-recombination, excitons, ... Design anti-reflection coatings or transparent cells
-
-
product
High Definition MWIR Science-Grade Camera
FLIR X8580™
The FLIR X8580 midwave IR camera is designed for scientists and engineers who need to capture detailed imagery of high-speed events, perform custom radiometric measurements, or detect points of failure in composites, solar cells, and electronics. This thermal imaging camera combines 1280 × 1024 HD resolution with fast frame rates and integration times, allowing researchers to record stop motion on fast-moving subjects or rapid temperature changes—whether in the lab or on the test range. With a four-position motorized filter wheel and support for FLIR motorized focus lenses, the X8580 will provide higher quality recordings, save time, and mitigate frustration in dynamic acquisition environments.
-
product
SR/QE Testing System
PVE300
Industrial Vision Technology Pte Ltd.
Solar Cell Multi-function SR/QE Testing System is specially designed for Photovoltaic Industry to characterize the Optical Performance of Raw material, process wafer, finished solar cell, as well as small Module.
-
product
Programmable 70W Electronic Load
MightyWatt R3
The All-New MightyWatt revision 3 turns your Arduino Uno R3 or Arduino Zero (M0/M0 Pro) into an electronic load capable of dissipating 70 Watts in a very small form factor. Ideal for testing power supplies, batteries, solar cells, fuel cells or power amplifiers. MightyWatt R3 has a research-grade electronics and is aimed not only at hobbyists but also at professionals.
-
product
Power Meters and Calibration Cells
The Solar Reference Cell consist of a 20 x 20 mm monocrystalline silicon Photovoltaic Cell encased in a 92 x 70 x 16 mm metal enclosure with a protective quartz window and a temperature sensor. The temperature sensor is a 100 ohm platinum Resistance Temperature Detector (RTD).The Solar Reference Cells come with a Certificate of Calibration and compatible set of connecting cables. The following parameters of the reference cell are certified: Isc, Imax, Voc, Vmax, Pmax, Area, Fill Factor and Efficiency. The certification is accredited by NIST to the ISO-17025 standard and is traceable both to the National Renewable Energy Laboratory (NREL), and to the International System of Units (SI). A compatible cable set is also supplied with each Solar Reference Cell.
-
product
IV Curve Tracer
IVCT
In recent years, we have been developing a sophisticated IV curve tracer for PV modules including a maximum power point tracking (MPPT) function. The IV curve tracer is designed for operation with any market-available steady-state solar simulator. Through our web-based software design, the operator can supervise the test results from every computer in a company network. The software contains functions such as an irradiation sum counter that helps to check requirements stated in a stabilization test like they are defined in IEC 61215 (MQT 19). We have also included a correction function to correct the traced IV curves to standard test conditions (STC) when the user enters the required temperature coefficients. One of the most important features is the multi-IV curve tracing function, which enables the user to display more than 150 IV curves in one graph. This eases the analysis of the weakest cells in hot-spot tests, which are required in IEC 61730 (MST 22) and IEC 61215 (MQT 09).
-
product
Characterization of Solar Cells
Paios
Paios performs a large variety of experiments in no time with one click. Get consistent and precise measurement data, directly compare your results in the measurement software and speed up your research.Increase your research speedCompare your devices directly in the softwareGet highly consistent dataThink about physics - Let Paios handle the rest
-
product
High Definition LWIR Science-Grade Camera
FLIR X8580 SLS™
The FLIR X8580 SLS is a high-speed, high definition longwave IR camera designed for scientists and engineers who need to capture detailed imagery of fast events, perform custom radiometric measurements, or detect points of failure in composites, solar cells, and electronics. This thermal imaging camera combines 1280 × 1024 resolution from the SLS detector with high-speed frame rates to offer shorter snapshot speeds and wider temperature bands for crisp stop motion imagery of high-speed events. With a four-position motorized filter wheel and support for FLIR motorized focus lenses, the X8580 SLS will provide high quality recordings, save time, and mitigate frustration in dynamic acquisition environments.
-
product
Large-size Hybrid Reverberation / Anechoic Chamber
F-Series
The F large-size hybrid Reverberation/Anechoic Chamber represents the most versatile OTA test system in the market today. With the same unique test features of their E Series RC counterparts, the F-Series can also test large form-factor devices under test (DUTs) like laptops, large TV sets, solar and trash compactors, drones, fridges or washing and vending machines, among others. With up to 16x16, 8DLCC and DUTs up to 2m and 500 kg including full-body phantoms in a turntable, the F Series also expands the frequency range down to cover 200 MHz up to 40 GHz frequency ranges and the test modes to include EMC, BS, small cell, eNodeB and Virtual Drive Testing over the air (VDT-OTA). In an again unheard-of feature, the F-Series is also reverse-convertible into an Anechoic chamber, allowing Far Field (FF) and Spherical Near Field (SNF) radiation patterns, efficiency and gain measurements and pre-5G testing of antennas and devices. Conversion from RC to AC or vice versa can be performed within half a day.
-
product
Solar Stimulator
XHS Series
They are mainly used for the evaluation of solar cells as well as for other types of tests where sunlight needs to be recreated.The continuous light of xenon lamp, the most faithful reproduction of sunlight, is applied in our highly accurate solar simulator, which has been widely sold across Japan and neighboring countries.
-
product
PV-IV Solutions
We offer a broad range of PV IV Measurement systems for measuring solar cells from 3 mm to 300 x 300 mm. The wide range of solar simulators, vacuum chuck test stations, and electronic loads make it impossible to list “standard solutions” Most systems are put together for individual customer needs based on cell type and contact geometry of the devices being tested. Over the last several years we have designed and manufactured a wide range test solutions for many different types of cells and contact geometries. In most cases a customized solution is no more than a slight customization of a standard platform that has been previously designed.
-
product
SOLAR CELL TESTER
The tester is designed for terrestrial solar cell incoming/outcoming inspection with the purpose of checking and optimizing parameters and preventing manufacture defects of solar modules. Solar cells are not heated in process of inspection due to the use of xenon pulse lamp installed in the tester.
-
product
Multiple Output Bidirectional PSU
LAB-MOBI
Electronic Test & Power Systems
The LAB-MOBI is a series of multi channel High Power Bidirectional PSUs. Each system is able to operate as either a DC Source or a DC Electronic Load. This integrated approach features high dynamics enabling the user to switch seamlessly between quadrants. When sinking energy from the unit under test the LAB-MOBI automatically inverts the DC to AC and synchronises this output to the grid. Dedicated application modes are available for battery cycling and emulation, which can be used to implement specific test routines. Other common applications the LAB-MOBI is used for include testing electric motors, fuel cells, super capacitors and solar panels. Max. Volt. Output 1000V,Min. Power 60kW, Max. Power 500kW.
-
product
Reference Cells For PIV-IV Systems
NREL calibrated cell used for calibration transfer.The Abet Technologies solar reference cell is a precision instrument for the determination of solar simulator irradiance levels. The sensor is a mono-crystalline silicon solar cell having an area of2x2cm(4cm).The back of the solar cell is attached to the device in such a way that a good heat transfer to the device housing is guaranteed. Below the solar cell a Pt100 RTD temperature sensor is mounted to allow monitoring of device temperature. The device is not shunted allowing the whole IV-curve to be measured. The solar cell is protected by a high quality fused silica window, assuring spectral sensitivity over a 320 -1100 nm range.
-
product
Flash Solar Power Meter
OAI’s Flash Solar Power Meter is a versatile measurement tool used for measuring the irradiance (in Suns) from Flash Solar Simulators. Flash Solar Simulators are commonly used in the production of solar panels. Integrated into the solar cell production line, this meter calibrates the flash solar simulator allowing for constant and repeatable irradiance output. By sampling at speeds up to 4000 Hz, the flash pulse temporal profile can be recorded in the meter’s memory and downloaded to a USB 2.0 port on a PC for further analysis.
-
product
Calibrated Solar Reference Cell
To insure repeatable testing on any solar simulator, OAI offers 2cm x 2cm calibrated reference cells. Standard reference cell calibration cycles can be set up by OAI''s calibration laboratory to insure that your reference cell maintains certification.
-
product
I-V Tracers
EKO I-V tracers (MP-160 / MP-11 / MP-180) can be used in three different Power ranges. The research type MP-160 is an all round instrument to be used with single cells and modules or multiple unitswhen connected to the multi channels selectors. The portable MP-11 with remote sensor unit can be used on site to accurately check the performance of Modules and Strings. The high end MP-180 is capable to make high precision I-V measurements of small and large size solar cells and is most suitable for Research and Development applications or production inspection purposes indoors.
-
product
Surface Photovoltage
The surface photovoltage spectroscopy modules are the perfect all-in-one solution for in-depth studies of light sensitive materials such as organic semiconductors, solar cells or light sensitive dyes.
-
product
Steady-state Solar Simulator For PV Modules
SORAS LS
In certification laboratories for photovoltaic modules, steady-state solar simulators are mostly used for stabilization / light soaking tests (MQT 19) and hot-spot endurance tests (MQT 09) according to IEC 61215 and IEC 61730. An initial stabilization is required for all PV modules that undergo a standard test procedure. For the hot-spot endurance test (MQT 09), it is important that the operator has easy access to the front and back site of the module. During the test, it is necessary to shade one cell after each other to take infrared pictures, which requires good visibility of the entire back side. Our swiveling module holding system enables easy access to the front and back side of the module.
-
product
Standard & Custom Test Fixtures
Both standard and custom Test Fixtures from OAI enable the user to integrate the solar cell with the I -V tester. Fixture configurations range from from simple hold down devices to temperature-controlled fixtures with front and back side contact. We invite you to contact an OAI Application Engineer for help with your fixture design. With our expert guidance, you can expect maximum performance from your I -V Tester and Solar Simulator.
-
product
Photovoltaic Array Simulation Solution
The Keysight N8937APV and N8957APV photovoltaic array simulators are capable of testing PV inverters up to 1,500 V, enabling designers to participate in the recent industry shift to the higher voltage. They can quickly simulate I-V curve characteristics under different environmental conditions (temperature, irradiance, age, cell technology and more), enabling the user to quickly and comprehensively test their solar inverters.
-
product
MOCVD Systems
TurboDisk Family
A rapidly developing technology with multiple proof-of-concept scale installations (1 MW or less), with many more larger-scale projects gaining momentum worldwide within regions with high direct normal irradiance (DNI). As/P MOCVD is proving to be the technology of choice in building the critical compound semiconductor layers for CPV devices. Veeco, supplying best-in-class MOCVD equipment, provides the critical enabling As/P MOCVD technology to reduce the production costs of triple junction solar cells and provides manufacturers with the ability to easily ramp production in a modular system with unmatched reliability and throughput at the lowest cost.
-
product
Flashlight Solar Simulator
Flashlight Solar Simulators have the advantage of negligible temperature change to the solar cell. For this reason, they are primarily used in cell and module production environments. Also, they are a more budgetary alternative if large cell areas are to be illuminated, because it is easier to have excellent light uniformity on areas of 8 in x 8 in or larger. So, this type of solar simulator is also used for analysis of large area thin film solar cells. But care must be taken, as some materials (e.g. CIGS) have long inherent time constants, so that the pulse length (better: flash plateau) must be chosen accordingly.
-
product
Solar Simulator
XES Series
The recent environmental issues have been drawing more attention over the past few years. So "solar simulators" have come into the public eye much more often. They are mainly used for the evaluation of solar cells as well as for other types of tests where sunlight needs to be recreated.The continuous light of xenon lamp, the most faithful reproduction of sunlight, is applied in our highly accurate solar simulator, which has been widely sold across Japan and neighboring countries."SAN-EI" offer a wide range of solar-related optical technologies and can guarantee to satisfy the needs and request of customers.
-
product
Light Initial Degradation Tester
King Design Industrial Co., Ltd.
Stable solar cells are needed for durability testing of different combinations of module ... cause, the focus fell on light induced degradation (LID) .... module using the same cells as in the initial modules was used.
