Solar Cell
Convert light to electricity.
-
Product
Fully Automatic Solar Cell
Module Laminator-H
-
1. Model: BSL2236OAC-H2. Effective lamination area: 2200mm × 3600mm3. Dimensions: length 17410mm × width 3665mm × height 2164mm4. Heating method: heat conduction oil heating5. Compressed air source pressure: 0.6～0.8MPa6. Working vacuum degree: 100～40Pa7. Evacuation rate: 70L/S8. Temperature control accuracy: ±1.5°C9. Temperature control range: room temperature - 180°C10. Temperature uniformity: effective lamination area≤±2℃11. Lamination chamber height: 30mm12. Evacuation time: depending on the process, it is recommended to take 5 to 8 minutes13. Upper cover stroke: 300mm
-
Product
Solar Cell Systems
-
he Solar Cell Scan is a multifunctionalexperimental platform,which is based on the measurement of Quantum Efficiency (QE) . The system employs a turnkey integrated design, which can carry out QE, Reflectivity and Mapping testing functions automatically. There are also modular and customdesigned accessories to adapt to different solar cell samples.
-
Product
Solar Cell Tester
-
Jiangsu Keyland Laser Technology Co., Ltd.
Features:- Up to standard IEC60904 & JISC8933- 24 hrs continuous working , over 300,000 flash- Siemens PLC system adopted- 10 Parameters display
-
Product
Solar Cell PL/EL/IV 3-in-1 Testing System
VS6841
-
Industrial Vision Technology Pte Ltd.
This luminescence Analyzer integrates a Photoluminescence (PL), Electroluminescence (EL) , and I-V Measurement Technology, has a Device’s PL image, EL image, as well Device’s I-V characteristics in One system. It is being using to quantitatively map Minority-Carrier Lifetime, and to characterize the defect of silicon wafer & solar wafer, and measure the key parameters from solar cell I-V Curve. It is also a useful tool for scientist to develop other methodology & parameters that can be used as a promising technique for online material monitoring and process control.
-
Product
Solar Cell I-V Characterization System
VS6821
-
Industrial Vision Technology Pte Ltd.
This system provides cell manufactures and laboratories a new way in testing and measuring photovoltaic cells. Integrated with Steady-State Solar Simulator, it provides complete coverage of testing parameters and measurement requirements by most international standards. Its test methods, procedure & equipment are IEC 60904 compliant. Calibration of reference cell is performed at Fraunhofer ISE in Germany, and is traceable to PTB.
-
Product
Solar Cell Tester
REOO RO-GTM2615
-
REOO RO-GTM2615 Solar Cell Tester is designed for PV cell manufacturing inspection, enabling fast cell performance inspection and stable electrical quality verification. Built for solar factories, it improves cell testing accuracy and maintains stable operation across PV cell production lines.
-
Product
Solar Cell I-V Characterization System
VS6825
-
Industrial Vision Technology Pte Ltd.
The VS-6825A I-V test system is tailored for high-efficiency Solar cell production lines. It is able to eliminate the impact of HJT/IBC/TOPCON’s high capacitance characteristics on measurement results.
-
Product
Solar Cell Simulation
Setfos
-
Setfos excels in analyzing and fitting experimental data, providing researchers with valuable insights and trend predictions. Complement your experimental work with Setfos for unmatched accuracy and reliability in data interpretation.
-
Product
SolarIV Series Solar Cell Current Voltage Measurement System
SlarIV
-
SolarIV IntroductionOne of the key measurements needed for photovoltaic devices in the measurement of their I-V characteristics. Through measuring the I-V curves the user can determine physical performances of devices such as photo-electric conversion efficiency, fill factors and so on. Such data is important for reliable work in research and quality inspection. ZOLIX supply the SolarIV system and the most perfect, professional technical support.
-
Product
Solar Cell Testers
-
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.
-
Product
Grid-Connection Testing System
-
This system is a power supply test system that performs grid-connection testing of distributed power sources (solar cells, fuel cells, gasoline engines, etc.)Enable inverter device testing that complies with the Agency for Natural Resources and Energy’s “Guidelines for System Interconnect Technical Requirements” and the Japan electrical Safety & Environment Technology Laboratories (JET) publication “Testing Methods for Small Solar Cell Power Generation System and System Interconnection Safety Devices”.
-
Product
Equipment
-
Based on a proprietary light engine, our solar simulation equipment delivers perfect and continuous artificial sunlight 24/7, allowing for accurate stability and performance assessments of solar cells at laboratory and industrial scales.
-
Product
Automated Testing System
PV-LIT
-
Thermographic solutions ensure high quality of solar cells and modules.Usable for all types of solar cells and modules (silicon-based or thin-layered)Testing in laboratory and in-line in the course of the manufacturing processTesting of various solar cells and modules through contact and non-contact measurementCell-specific system configuration and determination of test criteria and kind of defects
-
Product
Solar Simulator for Multijunction Solar Cells
-
For series connected multijunction cells, at a given spectrum (e.g. AM 1.5 or AM 0 for space solar cells), one of the cells will limit the current in the series connection of cells. All solar simulators deviate from the true AM 1.5 spectrum, and they are only classified in wide spectral bands (100nm width). So even for class A or A+ solar simulators, it can easily happen that the bandgaps of the multijunction cells are such distributed that the 'wrong' cell will limit the current, if a solar simulator with fixed spectrum is used. In the 70s and 80s, when these measurements were first developed, intercomparisons showed deviations of cell efficiency in fixed spectrum solar simulators of more than 40%.
-
Product
Saluki SEL7 Series Programmable DC Electronic Load (up to 6kW)
-
The new SEL7 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL7 series delivers high speed and high accuracy with a resolution of 0.1mV and 0.01mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL7 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.
-
Product
Reference Cells For PIV-IV Systems
-
NREL calibrated cell used for calibration transfer.The Abet Technologies solar reference cell is a precision instrument for the determination of solar simulator irradiance levels. The sensor is a mono-crystalline silicon solar cell having an area of2x2cm(4cm).The back of the solar cell is attached to the device in such a way that a good heat transfer to the device housing is guaranteed. Below the solar cell a Pt100 RTD temperature sensor is mounted to allow monitoring of device temperature. The device is not shunted allowing the whole IV-curve to be measured. The solar cell is protected by a high quality fused silica window, assuring spectral sensitivity over a 320 -1100 nm range.
-
Product
Photoelectrochemical Test System
SolarLab XM
-
SolarLab XM is an application specific XM (Xtreme Measurement) product that is primarily focused on solar cell / photovoltaic research, developed in conjunction with Professor Laurie Peter of the University of Bath, UK.
-
Product
Characterization of Solar Cells
Paios
-
Paios performs a large variety of experiments in no time with one click. Get consistent and precise measurement data, directly compare your results in the measurement software and speed up your research.Increase your research speedCompare your devices directly in the softwareGet highly consistent dataThink about physics - Let Paios handle the rest
-
Product
Stability Tester
Litos Lite
-
Litos Lite is a platform to perform parallel JV and stability measurements on organic, perovskite solar cells, perovskite/silicon tandem solar cells, and minimodules.
-
Product
Electronic Loads
-
PeakTech Prüf- und Messtechnik GmbH
Can be used for important test procedures in quality assurance as well as e.g. testing of power supplies and control units, batteries, fuel and solar cells. For precise load control for various purposes, this device offers load control according to constant voltage (CV), constant current (CC), constant load resistance (CR) or constant power (CP) with a highly precise resolution of 1mW, 1mV, 1mΩ and 1mA. The device also offers additional test modes, e.g. the battery test or the dynamic test. The PC interface and software offer the option of implementing freely programmable test sequences with data evaluation.
-
Product
Surface Photovoltage
-
The surface photovoltage spectroscopy modules are the perfect all-in-one solution for in-depth studies of light sensitive materials such as organic semiconductors, solar cells or light sensitive dyes.
-
Product
Programmable 70W Electronic Load
MightyWatt R3
-
The All-New MightyWatt revision 3 turns your Arduino Uno R3 or Arduino Zero (M0/M0 Pro) into an electronic load capable of dissipating 70 Watts in a very small form factor. Ideal for testing power supplies, batteries, solar cells, fuel cells or power amplifiers. MightyWatt R3 has a research-grade electronics and is aimed not only at hobbyists but also at professionals.
-
Product
High Definition LWIR Science-Grade Camera
FLIR X8580 SLS™
-
The FLIR X8580 SLS is a high-speed, high definition longwave IR camera designed for scientists and engineers who need to capture detailed imagery of fast events, perform custom radiometric measurements, or detect points of failure in composites, solar cells, and electronics. This thermal imaging camera combines 1280 × 1024 resolution from the SLS detector with high-speed frame rates to offer shorter snapshot speeds and wider temperature bands for crisp stop motion imagery of high-speed events. With a four-position motorized filter wheel and support for FLIR motorized focus lenses, the X8580 SLS will provide high quality recordings, save time, and mitigate frustration in dynamic acquisition environments.
-
Product
Solar Simulators
TriSOL CPV
-
Concentrating Photovoltaics (CPV) has the promise of producing solar cells with high cell efficiencies, which result in a reduction in the cost of operating a PV module. However, a CPV system requires the integration of CPV solar cells, modules and CPV optics into one efficient system. OAI’s focus is CPV cell testing methodology. The CPV cells can now be tested using OAI’s advanced standalone CPV Simulators for low dose and high dose configurations. The low dose CPV Solar Simulator provides exposure up to 50 Suns, whereas, the high dose CPV Solar Simulator provides exposure up to 1500 Suns. The low and high dose simulators provide exposure in varying Sun concentrations in various beam sizes from 1.5cm x 1.5cm to 7.5cm x 7.5cm, and may be configured with OAI’s I-V Test Systems.
-
Product
Stress-Test Platform
Litos
-
Litos is an advanced Solar Cell and LED stability lifetime measurement system, operated via Fluxim’s Characterization Suite (CS) software for complete control, data acquisition, and analysis. It has 16, or 32 parallel stressing channels distributed over 4 chambers, each with individual temperature and illumination control.
-
Product
Software
Solar Cells/ Photovoltaic Devices
-
Materials Development Corporation
MDC offers a comprehensive array of current-voltage, capacitance-voltage, and resistivity measurements to characterize solar cells and PV devices. CSM/Win systems and software can help to fine tune your process for maximum efficiency. Critical values such as series and shunt resistances, maximum power point (both actual and theoretical), and fill factor are automatically determined.
-
Product
Solar Stimulator
XHS Series
-
They are mainly used for the evaluation of solar cells as well as for other types of tests where sunlight needs to be recreated.The continuous light of xenon lamp, the most faithful reproduction of sunlight, is applied in our highly accurate solar simulator, which has been widely sold across Japan and neighboring countries.
-
Product
Datapaq Solar Tracker System
-
The SolarPaq® Thermal Profiling Systems from Fluke Process Instruments are designed specifically for solar photovoltaic (PV) manufacturing including applications like contact firing, contact drying, anti-reflection coating for the solar cell, lamination and other thin film processes. These systems, consisting of user-friendly Insight™ software, Datapaq® Q18 data loggers, stainless steel thermal barriers, thermocouples with PTFE or mineral insulation and accessories, provide users with the tools needed to gather accurate, repeatable results for process optimization, maximize cell efficiency and throughput, and more.
-
Product
Spectral Response SystemsQuantum Efficiency SystemsIPCE Measurement Systems
-
QE system provides electronics and software designed for fully automated measurement of external quantum efficiency of solar cells. All systems include probes and a fixed plate sample stage for samples up to 150 mm x 150 mm. The main system components include: custom designed software, measurement electronics, and computer system (Windows 8 operating system). The measurement involves focusing monochromatic light to a spot on the device under test, then accurately measuring the photon flux and current from the test cell. The system utilizes a dual beam configuration with lock-in detection, providing an absolute accuracy of ±3%. The QE system uses a grating monochrometer with silicon/InGaAs/Ge detectors. The system includes automatic order sorting filters and two light sources for monochromatic illumination (a Xenon- arc lamp and a halogen lamp). A single lock-in amplifier is used to measure both the reference detector and test device. The main system comes with all the hardware needed to measure quantum efficiency, a fixed plate sample stage and probes.
-
Product
Modular Solar Array Simulators
MP4300A Series
-
The output power of solar cells varies with numerous environmental conditions (e.g., temperature, irradiation) and operational conditions (e.g., eclipse, spin). The Keysight MP4300A Series solar array simulator enables you to test all these conditions with high accuracy. It delivers fast current-voltage (I-V) curve changes with a quick recovery time, emulating rapidly changing conditions.
