RS-422
One of several standards that incorporate balanced line signals into DB connectors. A pair of wires is used to carry each signal. The data is encoded and decoded as a differential voltage between the two lines. (www.sangoma.com)
-
Product
RS-422/RS-485 Repeater
ND-6510
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
Interface RS-485 and RS-422
-
The RS-485 specification meets the requirements for a truly multipoint communications network, and the standard specifies up to 32 drivers and 32 receivers on a single (2-wire) bus. Some RS-485 transceivers modify the input impedance to allow up to 8× more nodes to be connected to the same bus. Analog Devices offers a wide range of standard RS-485/RS-422 transceivers and iCoupler® isolated RS-485/RS-422 transceivers to suit many applications.
-
Product
RS-422/485 Serial Communication Card
PCI-COM-1S
-
The PCI-COM-1S is a single port asynchronous serial communications card that can be installed in any 3.3V or 5V PCI slot computer. The card meets the MD1 PCI Low Profile Specification and is just 4.7 inches long. For low profile systems please use P/N LPCI-COM-1S for the card to be shipped with a low profile bracket.
-
Product
- RS-422 Opto Isolation Module
Model 8381
-
FEATURES: Opto Isolation; Built-in Power Supply; 115.2 KBPS Data Rate; DIN Rail Mounted; Full Duplex; Programmable Terminations. The Model 8381 RS-422 Opto Isolator allows re-generating and extending the distance of RS-422 networks while maintaining optical isolation between the ports. Model 8381 allows for the extension of RS-422 links to a maximum limit of 3,300 feet or 1 km at any data rate up to 115 KBPS.
-
Product
Universal PCI, RS-422 Or RS-485 Serial Interface Cards
LPCI-COM422-8 and LPCI-COM485-8
-
These are eight-port, asynchronous, serial communication cards designed for use on the PCI bus. They support RS-422 or RS-485 communications. These cards offer the best combination of high-density and high-speed communications in a low profile form factor. The cards meet the MD2 Low Profile PCI Bus Specification and can be used in applications where space is at a premium, such as thin-client servers and high-density rack-mount servers. The LPCI line has been designed for use in retail, hospitality, and point of sale systems as well as the gaming and defense industries.
-
Product
PCIe Fast Multifunction, Multichannel Counter Board, Optically Isolated, RS-422 Inputs
APCIE-1711-5V-I
-
The APCIe-1711 board is a fast multifunction and multichannel counter board for the PCI Express bus. The strengths of this board are its wide range of applications and high precision and reliability for industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provide the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied software. The flexible programming facilities on this board allow many differentuser applications to be quickly and easily developed and reconfigured as further requirements arise. Thanks to the FPGA board structure, further counting applications canbe realised through software adaptation.
-
Product
- RS-232 to RS-422/RS-485 Converter
Model 285
-
FEATURES: User Selectable RS-422 or RS-485; User Selectable 2 or 4 Wire RS-485; Intelligent Control Of RS-485 Transmitter And Receiver; TD & RD LED's; DTE/DCE Compatible; Data Rates Up to 64 KBPs. The Model 285 RS-232 to RS-422/RS-485 Converter is a unique interface converter that can be configured to operate in compliance with RS-485 or RS-422 equipment, and RS-232.
-
Product
RS-485, RS-422 & RS-232
-
Renesas has a rich interface history dating back to the 1970s. Our RS-485, RS-422 and RS-232 transceivers are used by the biggest names in industrial process control, telecommunications, and hundreds of different applications.
-
Product
LAN⇔RS-422/RS-485 Conversion
SI-65A
-
SI-65A is an interface converter to connect factory automation equipment and analyzers, which only have the serial communication ports for RS-422/485, to LAN.
-
Product
RS-232 to RS-422 Interface Converter
Model 63-2SA
-
FEATURES: Full Duplex Signals; DTE/DCE Switch; TD and RD Indicators; DC to 115.2 KBPS. The Model 63-2SA provides a hardware conversion for full duplex signals between RS-232 and RS-422 I/O ports. Since the RS-232 port may look like a computer or a modem, the converter is equipped with a DTE/DCE selector switch.
-
Product
RS-422/485 Serial Communication Card
LPCI-COM-1S
-
The PCI-COM-1S is a single port asynchronous serial communications card that can be installed in any 3.3V or 5V PCI slot computer. The card meets the MD1 PCI Low Profile Specification and is just 4.7 inches long. For low profile systems please use P/N LPCI-COM-1S for the card to be shipped with a low profile bracket.
-
Product
- RS-422/485 DIN Rail Mounted Lightning/Surge Protector
Model 8022NX
-
FEATURES: Fast Response; Automatic Recovery; Up To 20 MBPS Data Rate; DIN Rail Mounted; Full Duplex; Triple Stage Protection. The Model 8022NX is a DIN Rail mounted surge suppressor for 4-wire RS-422 or RS-485 circuits used to protect factory data networks, or, any network that wants to avail itself of the DIN Rail packaging concept. The Model 8022NX provides common-mode (line to ground) surge protection and differential mode (line to line) protection for balanced networks. All the inputs, outputs and ground connections are via screw terminals located on the top surface of the device.
-
Product
Cable Assembly, Receiver, TriPaddle, 36", 2 9-Pin Female D-Subs, for RS-422/485
540041010201
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 36", 2 9-Pin Female D-Subs
-
Product
Isolated RS-422/485 Communications and Watchdog Card
WDG-SIO
-
This multifunction card contains a Watchdog Timer, an RS422/485 Serial Communications port, and an internal Temperature Alarm. The WDG-SIO is a full-length card that installs in “long” expansion slots of IBM PC/XT/AT and compatible computers. The following paragraphs describe functions provided by the WDG-SIO card.
-
Product
8 Serial Communication Channels, Programmable RS-232/422/485 Non-Isolated
SC3
-
Serial Communication Module SC3 provides up to 8 high-speed, programmable RS-232, RS-422, RS-485, non-isolated communication channels. Each channel is programmable for either Serial Communications (SC) protocol or General Purpose I/O (GPIO) modes as either RS-422/485 (differential) or RS-232 (single ended) hardware level interfaces.
-
Product
- RS-232 to RS-422 Interface Converter
Model 263
-
No AC or DC Power; Full Duplex RJ-11 and Screws; Surge Protection. The Model 263 power stealing RS-232 to RS-422 interface converter offers the user the benefits of other Telebyte converters without the problem of supplying power. With only TD, RD and Ground the Model 263 will provide operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
Product
RS-232 to RS-422/RS-485 Interface Converter
Model 365
-
FEATURES: User Selectable RS-422 or RS-485; User Selectable 2 or 4 Wire RS-485; DataSpy® LCD Display; Intelligent Control of RS-485 Transmitter and Receiver; DTE/DCE Compatible; Data Rates Up to 115.2 KBPS. The Model 365 multimode interface converter allows operation in compliance with RS-485 or RS-422 equipment, and RS-232.
-
Product
RS-232 to RS-422/RS-485 Interface Converter
Model 9365
-
FEATURES: DIN Rail Mountable; User Selectable RS-422 or RS-485; User Selectable Two- or Four-wire RS-485; DataSpy® LCD Display; Intelligent Control of RS-485 Transmitter and Receiver; DTE/DCE Compatible; Data Rates Up to 115.2 kbp.
-
Product
LAN⇔RS-422/RS-485 Conversion
SI-65
-
SI-65 is an interface converter to connect factory automation equipment and analyzers, which only have the serial communication ports for RS-422/485, to LAN.
-
Product
4-Port RS-422/485 Isolated Serial Communications Card
cPCI-3544
Communications Module
- 32-bit CompactPCI®, PICMG® 2.0 Rev 2.1- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS- Four asynchronous communications ports with intelligent buffer- Four RS-422/485 ports- 2500 VRMS isolation voltage
-
Product
RS-422 RS-423 RS-485
-
The low-power, high-speed transceivers of this family are designed for RS-485, RS-422 and RS-423 communication applications. They usually contain one driver and one receiver in half duplex configuration. Each driver output and receiver input is protected against electrostatic discharge up to ± 15 kV and has no latch-up. These transceivers operate with a 5 V supply and draw a very low supply current when unloaded or fully loaded but with disabled drivers.
-
Product
RS-232 to RS-422/RS-485 Optically Isolated Interface Converter
Model 245
-
Total Isolation; Selectable RS-422 or RS-485; Selectable 2 or 4 wire RS-485; Intelligent Control of RS-485; TD & RD LED's on Each Side of Opto Barrier; Data Rates up to 128 KBPS. The Model 245 RS-232 to RS-422/RS-485 Optically Isolated Interface Converter is an optically isolated version of the Model 285.
-
Product
ULI-234TE - Heavy Industrial RS-422/485 (Terminal Block) Isolated Repeater
BB-485OPDRI-PH
Terminal Block
RS-422/485 Repeator2kV, 3-way isolation (input/output/power)Data rates:1.2 to 115.2 KbpsWide operating temperature range: -40 to +85 °CIEC-61850-3, IEEE-1613, NEMA TS2, FCC, CE10 to 48 VDC input power (power supply required, sold separately)
-
Product
RS-422/485 Repeater
ADAM-4510
Signal Repeater
Automatic RS-485 data flow controlSurge protection RS-485 data lineTransmission speed up to 115.2 KbpsNetworking up to 1200 meters (4000 feet)LED indicator to monitor status
-
Product
Single Port RS-422/485 Serial PCMCIA Card With Detachable Cable
SSP-200/300
-
The Quatech SSP-200/300 offers a convenient way to add a single RS-422/485 serial port to your laptop, PDA, or desktop (using one of Elan's Desktop PCMCIA adapters - P111, P222 etc.). The card automatically configures to become another COM port using the supplied drivers that are tried, tested, and optimized for Windows.
-
Product
Multi Protocol Analyzer
LE-2500R
-
LE-3500R/LE-2500R adopted TTL port as its standard besides RS-232C, RS-422, and RS-485 while having the same feature such as small and light body of LE-3500/LE-2500. You can monitor I2C or SPI without expansion board.
-
Product
GPIB to Quad Serial Interface
Model 4896
-
* Provides four RS-232/RS-422/RS-485 Serial Channels.* High speed, 115.2 K baud channels include 60 K byte buffers.* > 600 K byte/sec. GPIB data transfer rate.* SCPI commands set serial configuration and GPIB address.* LCD display shows Bus activity, buffer status, serial interface signals and channel settings.* 1 U high rack mount kit mounts one or two 4896s * Includes US 115 VAC Power Adapter, Manual and Support CD.
-
Product
8-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V/5V
APCI-7800-3
-
8-port serial interface, RS232, RS422, RS485, 20 mA CL, modular mounting
-
Product
RS-232 to RS-422/RS-485 Converter
ND-6520
-
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
