-
Product
50 MHz to 40 GHz USB Peak and Average Power Sensor
U2022XA
Power Sensor
Keysight U2020 X-series USB power sensors provides the peak and average power measurement capability of a power meter in a compact and portable form factor.
-
Product
USB-6366, 8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
781445-02
Multifunction I/O
8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6366 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard … NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6366 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Single Channel USB Programmable Instrumentation Amplifier
USBPIA-S1
-
The USBPIA-S1 stand alone USB controllable module provides a single channel of high-quality instrumentation amplifier and optional AC coupling, for front-end signal conditioning compatible with all popular A/D converter devices. The USBPIA-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPIA-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPIA-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
Product
10 MHz to 50/53 GHz USB Wide Dynamic Range Peak and Average Power Sensor
U2065XA
Power Sensor
The Keysight U2065XA is a fast, accurate and wide dynamic range 10 MHz – 50/53 GHz USB peak and average power sensor.
-
Product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
Digital / Synchro Converter
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
Product
Bench/portable Universal Counters With USB Interface 3GHz Or 6GHz
TF900 Series
-
Frequency, period, pulse width, frequency ratio, duty cycle, and event counter modesDC to 3000 or 6000MHz range, 0.001mHz resolutionHigh impedance measurement up to 125 MHzAC or DC coupling, 1M/50Ohm selection, polarity invertSwitchable attenuator, threshold controlNoise filter for low frequency measurementsSelectable measurement time; display hold functionLarge 10 digit display with full range of annunciatorsInternal rechargeable batteries for portable useUSB interface provides full remote control and readback
-
Product
USB-6356, 8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
781444-02
Multifunction I/O
8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6356 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6356 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Bench Digital Multimeter, 4.5, USB, 20 A, 750 V, 0.2 Gohm
72-13625
-
This 72-13625 is a manual range, benchtop digital Multimeter that features 19999 display counts, large LCD screen with backlight, full scale overload protection and a unique design. This instrument can be used to measure AC and DC voltage, AC and DC current, resistance, frequency, capacitance, transistor, hFE, diode (LED), SCR, continuity, etc.
-
Product
ARINC 429 Test And Simulation USB Module
USB-429
-
*4, 8 or 16 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
USB-6343, 32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device
782253-01
Multifunction I/O
32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device - The USB‑6343 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6343 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Saluki S8723X Series USB CW Power Sensor (9kHz - 40GHz)
-
S8723X series is a diode detector USB power sensor based on a USB 2.0 full-speed/high-speed adaptive interface. It has a wide frequency range and large power dynamic range. It can be connected to a computer or other electronic measuring instruments, easy to set up a power test system, particularly useful for field and other low-cost production line testing and power testing.
-
Product
8-Ch Relay And 8-Ch Isolated Digital Input USB Module
USB-4761
USB Module
Compatible with 1.1/2.0Bus-powered8 relay output channels and 8 isolated digital input channelsLED indicators to show activated relays8 Form C type relay output channelsHigh-voltage isolation on input channels (2,500 VDC)High ESD protection (2,000 VDC)Wide input range (5 ~ 30 VDC)Interrupt handling capabilityPortableDetachable screw terminal on modulesSuitable for DIN-rail mountingOne lockable USB cable for secure connection included
-
Product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-94
Serial Interface
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
USB/GPIB Interface High-Speed USB 2.0
82357B
Interface
Easily connect to GBIP instruments from a USB port; no switches, no PC cards, and no external power supplies required.
-
Product
3.5" Embedded SBC With AMD LX800, Dual LANs, 4 COM, 4 USB 2.0 And VGA/LVDS/TTL
SBC84622
-
The SBC84622 supports an onboard low power AMD LX800 500 MHz processor with the AMD Geode CS5536 chipset. The flexible display function is supported by integrated graphics controller which allows users to configure both CRT and LVDS LCD or CRT and TTL LCD as simultaneous mode. Onboard one DDR SODIMM supports up to 1GB of system memory. Having such compact design with fanless operation, the SBC84622 can be applied in widely embedded and automation applications such as industrial automation, automation control, telecommunication, and process control.
-
Product
SparkFun USB Type A Female Breakout
-
This simple board breaks out a female USB type A connector's VCC, GND, D- and D+ pins to a 0.1" pitch header. If you want to add a USB to your project, but don't want to put up with soldering tiny connectors, this is the board for you.
-
Product
HDLC RS-232 / RS-422 / RS-485 Passive Tap Module – USB Port
VERSA-TAP™
-
Versa-Tap protocol analyzer offers a powerful hardware solution that features state-of-the art electronics and provides exceptional data-logging/analyzer capabilities at a fraction of the cost of the nearest competitor.
-
Product
USB-6341, 16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
782250-01
Multifunction I/O
16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB‑6341 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6341 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PathWave BenchVue USB Modular DMM Pro
BV0021B
-
Connect and control your U2741A DMM to make measurements, plot graph and log unrestricted data with PathWave BenchVue USB digital multimeter software.
-
Product
ATSC 3.0 Modulator for Lab
ATSC 3.0 LabMod
-
ATSC 3.0 LabMod is the STL Gateway compliant modulator for laboratories. Compact, portable and easy-to-use, LabMod covers the whole ATSC 3.0 standard with LDM support. In addition, LabMod performs channel simulation, noise generation, RF spectrum analysis and RF recording/playing. ATSC 3.0 LabMod is the perfect modulator for discovering ATSC 3.0 standard: generate live ATSC 3.0 RF signals or IQ pattern files, record live ATSC 3.0 transmission in different places over the world (optional) and playback them to test your receiver.
-
Product
Portable Avionics Interfaces for USB 2.0
Interface
These versatile interfaces are suitable for a wide range of applications in the lab and in the field. They support maximum data throughput on all channels and have a large 32 MB built-in memory. All power necessary for operation is provided via the single USB port. Plug and Play and Hot Swap features make them easy to install and move between computers.
-
Product
10 MHz To 54 GHz USB Wide Dynamic Range Average Power Sensor
U2056XA
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis
-
Product
Streamline USB Vector Network Analyzer, 14 GHz
P5023A
Vector Network Analyzer
Compact, faceless, USB vector network analyzer (VNA). Flexible two-port VNA which dramatically reduces your size of test. Up to 14 GHz.
-
Product
64 Output USB Modular Digital I/O
U2653A
Digital I/O Module
The Keysight U2653A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
Product
DC to 120 GHz USB Thermocouple Power Sensor
U8489A
Power Sensor
The U8480 Series is the fastest USB thermocouple sensor in the world without compromising the best-in-class linearity of the legacy 8480/N8480 Series thermocouple sensors. The U8489A covers the widest frequency range, DC to 120 GHz.
-
Product
USB, AC 110 VOLT AND 12 VOLT SOCKET TESTER PACK
MDPPTST
-
*USB, 12V and AC 110V socket testers provide the user with a simple way to test electrical sockets on a vehicle*Socket testers illuminate when when the respected voltage is detected, indicating the health of the socket*USB socket tester illuminates when 4.4V - 5.25V is detected
-
Product
USB-8502, 1-Port, High-Speed/FD, USB CAN Interface Device
784661-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
8/16-CH 16-Bit 250 kS/s Multi-Function USB DAQ Modules (OEM Version Available)
USB-1901/1902/1903
Data Acquisition Module
The ADLINK USB-1900 series provides a range of USB 2.0-based multi-functional DAQ modules. The USB-1901 and USB-1902 16-bit 250 kS/s USB 2.0-based high-performance DAQ modules allow four different voltage input ranges, while the USB-1903 features additional built-in precision current-tovoltage resistors capable of direct measurement of current signal from 0 to 20 mA. The USB-1900 series is USB bus powered and equipped with removable screw-down terminals for easy device connectivity. The attached multi-functional stand can be used for desktop, rail, or wall mounting. Suitable for mixed-signal tests, laboratory research, and factory automation, the USB-1900 series provide a simple measurement solution at an affordable price.
-
Product
Streamline USB Vector Network Analyzer, 53 GHz
P5008A
Vector Network Analyzer
Compact, faceless, USB vector network analyzer (VNA). Flexible two port VNA which dramatically reduces your size of test. Up to 53 GHz.
-
Product
Interface Board, 8:1 USB
40-965-903
Interface
Converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 8 USB type A and 1 USB type B connectors. Allows the multiplexing of up to 8 USB1 or USB2 signals.
