Electromagnetic Simulation
models and predicts the character of electromagnetic fields. Electromagnetic Field
See Also: Electromagnetic, EM Simulation, Electromagnetic Radiation
-
product
MIL-STD-1553 Test & Simulation Instrument for VXI
VXI-1553
Avionics Interface Technologies
Dual redundant, multi stream configurations availableSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Real-Time recording and physical bus replayANSI Application interface supporting C, C++, C#, and .NET development - VISA based VXI “Plug & Play’ Device driver provided
-
product
ECU Simulators
Easily configurable and customizable ECU solutions. Perfect for use as gateway nodes, simulators, automated testers, and ECU replacements.
-
product
SAE AS5643 Mil-FireWire PXI Express Test & Simulation Instrument
HSSUB-6120
Avionics Interface Technologies
Highest density capability available in an AS5643 3U PXI Express, single slot instrument - Four (4) FireWire nodes, each with three (3) ports - Apps provide high-level (AS5643) and low-level (1394) access, while accommodating end-user customization - S100, S200, S400, S800 transfer rates - Support all Nodes operating concurrently at 800 Mbps - Independent transformer coupling for each port - Eight (8) standard PXI backplane triggers - Industry standard Texas Instruments IEEE 1394b Chipset - ANSI C (typical), C++/C#/LabVIEW
-
product
Acceleration Simulation Mode (ASM) for Single Driven Axle Vehicles
ASM_AF | VP 230045
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-AF roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The ASM-AF is built into the base.
-
product
3-Axis Motion Simulators
When a device under test needs to be stimulated with simultaneous movements around three axes, then a product from the ACUTRONIC three-axis motion simulator range is the right choice. Independent motion simulation in three axes makes them very versatile: they are used as Inertial Guidance Test Systems (IGTS), for HardWare-In-the-Loop (HWIL) testing, for the test of optronic pointing devices, and many more applications.
-
product
IBP Simulator
IBPS 2.0
The IBPS 2.0 is a PC controlled simulator to replace real IBP sensors. Originally designed for IEC 60601-2-34 testing, it can also be used by manufacturers to play their own test signals or database recordings.
-
product
IMU MODELING AND SIMULATION
CAST Navigation’s INS systems provide high rate inertial data with exceptional fidelity to support the integration and testing of today’s complex EGI and GNSS/INS navigation systems. The CAST system is designed for optimal performance when the inertial sensor and GNSS receiver are either loosely, tightly or ultra-tightly coupled, or when an INS aiding source can be utilized by any other type of device.
-
product
16-Channel VME Analog Output/Thermocouple Simulator Module
V470
The V470 is a 6U VME module that provides sixteen independent, isolated analog outputs that may be user-programmed to operate as voltage outputs or thermocouple simulators. Users may write temperature or voltage values at VMEbus speed, and the microprocessor will transparently do all necessary calculations and update the channel electronics.
-
product
2 PRI + 24 BRI-S/T ISDN Simulator
CH-24BRI-ST-MOD-2PRI
This unit has two PRI ports and 24 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
product
IP / VoIP Analysis & Simulation
GL offers high density Ethernet/IP tester variant which includes mTOP™ 1U/2U rack mount enclosures within which PacketExpert™ portable USB units are stacked to provide high density GigE ports form factor solution for testing GigE switches, routers and network conditions.
-
product
Load cell simulator
PC2M
PC2M signal calibrator has been realised to perform periodicalchecks and calibrations on indicators with a 2mV/V input anda 4 or 6 wires systems. Provided with a main switch with 6 selectable steps, it allows to control the linearity on both positive and negative field. Internally, the 350W full bridge unbalancing, is generated by high stability passive resistances (1 ppm/C).
-
product
MIMIC NetFlow Simulator
MIMIC NetFlow Simulator generates a variety of flows and enables you to fully test your applications. Since you have a complete control over generated flowsets you can easily verify that your graphing application is correctly displaying the values and your collector correctly collects precisely generated flowsets.
-
product
Fiber Optic Network Simulators
SIM-2FON-25
Vconsole fiber optic network simulator is custom built portable unit intended to simulate installed fiber optic facilities. Vconsole will design and build custom unit exactly to customers specification. The enclosure is capable of housing an individual spool with up to 100km of fiber. We will build each unit to client unique needs with custom fiber types, lengths, and connectors. A full range of connectors are available including SC, ST, FC, and LC types. This product is ideal for latency testing, product development and training and educational needs.
-
product
Emulate Test in simulation
STIL-VT
Emulate test patterns in simulation environment with DUT simulation model. The simulation allows pre-silicon debug of test patterns. Reads the intermediate STIL format of tester patterns and creates a Verilog /VHDL simulation test bench. (A sub-set of Virtual tester solution)
-
product
MIL-STD-1553 A / B Test And Simulation XMC Module
XMC-1553
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
product
Steady-state Solar Simulator For PV Modules
SORAS LS
In certification laboratories for photovoltaic modules, steady-state solar simulators are mostly used for stabilization / light soaking tests (MQT 19) and hot-spot endurance tests (MQT 09) according to IEC 61215 and IEC 61730. An initial stabilization is required for all PV modules that undergo a standard test procedure. For the hot-spot endurance test (MQT 09), it is important that the operator has easy access to the front and back site of the module. During the test, it is necessary to shade one cell after each other to take infrared pictures, which requires good visibility of the entire back side. Our swiveling module holding system enables easy access to the front and back side of the module.
-
product
Environmental Simulation
During the development phase of new products, we analyze the weak points in simulation tests and test the products for environmental influences. The relevant standards are used as the basis for the simulation tests.
-
product
Solar Simulator Continuous Light
This type of solar simulator uses Xenon high pressure arc lamps as light source. These lamps have a colour temperature near 5800 K, so it is feasible to filter the light output to an excellent AM 1.5 spectrum. If a tuneability of the spectrum is required, these lamps can be combined with tungsten lamps to achieve multi-source solar simulators. These can be used to measure tandem/triple/multijunction solar cells. They also allow detailed analysis of all types of solar cells using a spectral metric (see : Publication List).
-
product
Solar simulators
Solar simulators enable the measurement of (dark and) light IV characteristics and of power and efficiency of photovoltaic An artificial light source is used to create illumination conditions that are similar to those in natural sunlight. International standards hosted by ASTM, IEC and JIS allow to classify the properties of a solar simulator with respect to spatial light uniformity, spectral content of the light and time variation of intensity.
-
product
Time Domain Replication (Road Load Simulation)
The powerful graphical editor makes it easy to review and compile your field sample data for use in the test lab. The point editor, filters, velocity and displacement compensation ensure the test feasibility is evaluated at an early stage. The continuous closed-loop controller then replicates the test files with very high levels of precision. The control algorithms use a continuous coherence averaging technique to ensure a stable proactive control loop that will not only provide accurate replication but will also respond to changes in test item dynamics.
-
product
Electronic Circuit Simulator
SimOne
SimOne lets you perform full-featured electronic circuit simulation using state-of-the-art and classic modeling algorithms while taking full advantage of modern computers.SimOne does all the basic circuit analyses common to SPICE modeling systems and as well provides important Stability analysis.
-
product
Portable Range Threat Simulators
The Textron System's PRTS™ and HPRTS™ are medium and long-range, programmable, ruggedized Radio Frequency (RF) test and training tools. Our PRTS family of range simulators delivers high-fidelity environments for training ranges.
-
product
Steady State Solar Simulator
Our steady state solar simulators enable you to test and develop solar thermal collectors independent of weather and season, faster, more efficiently and more comprehensively than ever before. Both simulators are turnkey products, delivered 100 % ready to go!
-
product
Electromagnets
The Lake Shore electromagnets (EM-V Series) produce magnetic fields with a variety of indexed air gap and pole cap configurations. The EM-V Series is ideally suited for integration into customer-designed magnetic test platforms for applications including magneto-optical studies, magnetic hysteresis studies, in-line annealing, Hall effect studies, susceptibility measurements, spin magnetic resonance demonstrations, and biological studies.
-
product
Interference Simulation System
GSS7765
Combined with Spirent’s powerful GSS7000 or GSS9000 Series simulators, the GSS7765 interference generator creates the ultimate tool for testing against external jamming and unintentional interference. The GSS7765 enables you to create and generate custom waveforms, helping you to defend your systems against real-world threats.
-
product
Dual Channel Gigabit Ethernet Test & Simulation Instrument for PCI Express
PCIe-DCE
Avionics Interface Technologies
Dual channel, high precision Ethernet Test Instrument
-
product
Simulate millions of real-world end-user environments
PerfectStorm
Keysight Network Applications and Security
The next generation of our well-received PerfectStorm 10/40GbE platform is available now. PerfectStorm 100GbE is the world's only native 100GbE testing platform, far ahead of other test solutions, the closest of which offers just 10GbE native interface support. The new platform comes to market at the right time, as equipment sales of 100GbE are ramping in Service Provider and Enteprise Data Center.
-
product
Regenerative Grid Simulators
Chroma Systems Solutions, Inc.
Rigorous testing to industry regulatons and standards for the safe operation of on-grid products.
-
product
Software Adaptive Modeling & Simulation of Nanosystems
SAMSON
SAMSON is the quickly growing platform for integrated molecular design. SAMSON's goal is to make it faster for everyone to design drugs, materials and nanosystems. For fun, or to build a better tomorrow through science and innovation in medicine, energy, materials, electronics, education, and more. SAMSON is available on all major operating systems.
-
product
Software for Test, Analysis and Simulation applications
AIM Software Solutions
AIM offers PBA.pro Software for Test, Analysis and Simulation applications. PBA.pro is compatible with Windows and LINUX Operating Systems and supports most of the AIM interface hardware modules. The flexible, scalable and open PBA.pro concept supports a wide spectrum of customer applications.
