Noise Sources
create signal disturbances for the purpose of noise instrument calibration.
See Also: Pink Noise, Noise Generators
-
product
32-CH Sourcing Type Digital Input EtherCAT Module
EPS-1032
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
product
10 GHz Signal Source
YIG Series
The SC5503B and SC5502A are designed to meet demanding low phase noise applications. This is accomplished by employing a multiple phase-locked loop architecture as well as a YIG oscillator as the heart of its synthesizer. Frequency accuracy is provided by an onboard 10 MHz temperature compensated crystal oscillator (TCXO) which can be phase locked to an external reference source if required. These modules can be used as standalone CW signal sources or as LO sources for frequency conversion systems such as the SignalCore IQ modulators and demodulators. They are designed to meet the requirements of many modern applications such as wireless device testing, software-defined radio research, point-to-point radio, multi-channel coherent systems, and other academic and military programs.
-
product
PCI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Output, Bank-Isolated Digital I/O Device
778836-01
The PCI-6514 is an industrial digital I/O interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in … software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
Programmable Bidirectional AC Laboratory Power Supplies (source / Sink)
Programmable Bidirectional AC Laboratory Power Supplies (source / Sink)
-
product
Laser-Pumped White Light Source
LS-WL1
Our LS-WL1 is a laser-pumped white light source with a light output of up to 440 mW from a 600-µm fiber and a wavelength range of 450 – 700 nm, designed especially for professional requirements for extremely high luminance.
-
product
High-Standard Bench-Top Laser Source
Shanghai Stone Communication tech Co., Ltd
These bench-top laser source has built-in high-feature Semi-conductor laser device, it is the SM output, with less than 10MHz plus width. Based on the advanced micro-processor control system, this instrument integrated high precision ATC and ACC(APC) to control the electric circuit, in order to realize the high stable output of the laser device, and make the operation easily and directly. We also can provide user required communication port with the software to realize remote control from the PC.
-
product
16-Channel VME Current Source & Analog Measurement Module
V460
The V460 is a VME-based versatile source/measurement unit. It includes a programmable constant-current source, a precision programmable gain 16-bit analog-to-digital converter, and a 4-wire, 16-channel analog multiplexer. An internal microprocessor supervises channel scanning according to user loaded parameters, reporting sensor voltage drops or, for selected sensor types, engineering-unit data.
-
product
Impulsive Sound Source
BAS006
The BAS006 is an innovative device used to create impulsive noise that includes low frequency energy and avoids problems like secondary bounce. These characteristics make it a great choice for quickly measuring reverberation time when the complexity and weight of a speaker and amplifier is not needed.
-
product
SpikeSafe DC Current Sources
The Vektrex SpikeSafe DC Current Sources provide reliable drive for LED/laser diode reliability, IESNA LM-80 test, and other current-driven test applications. Models support currents from 500mA to 60A and compliance voltages from 50V to 400V. All models feature individual channel control, precise current, and high power density — typically 6.4kW-8kW.
-
product
Programmable AC Source
6500
Chroma Systems Solutions, Inc.
1200VA ~ 9KVADirect Digital Synthesis (DDS) waveform generationProgrammable voltage, current limit, frequency, phase, and distortion
-
product
Downward-Looking SUMO Source For Gallium And Indium
Attain large capacity, excellent flux uniformity, negligible shutter flux transients, and minimal depletion effects with Veeco’s Downward-Looking SUMO® Source for MBE. It combines a dual filament source with an asymmetric SUMO crucible featuring a narrow offset orifice and tapered exit cone with hot-lip heating. Result: excellent material quality, low defect counts, and good thickness uniformity. NOTE: This source is not for use with aluminum.
-
product
Precision Programmable AC and DC Sources, 0 - 333VAC, 0 - 3,000A / Phase, 15kVA - 1.08MVA
Tahoe Series
AMETEK Programmable Power, Inc.
The California Instruments Tahoe Series combines intelligence and flexibility with high power to create an advanced platform of AC solutions. Using a state-of-the art SiC power switching architecture and Digital Signal Processing, the Tahoe Series combines a robust, high-power AC/DC source with an advanced power analyzer in a single floor standing chassis.
-
product
AC Power Source
SPS-100
Kongter Test & Measurement Co., Limited
SPS-100 is designed for various tests of analog and digital AC Voltage meter and Current meter, Single/three phase active and reactive power meter, Phase angle meter, Single/three phase power factor meter, frequency meter, and synchronous-meter, Single/three phase active and reactive power meter; it also outputs 2nd ~63rd harmonics.
-
product
PXIe-4137, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit
783761-02
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4137 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology helps you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4137 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers
-
product
Noise Figure Meters
H5M Series
*Frequency range from 10 MHz to 4/20 GHz*Noise Ratio and Gain measurements*Frequency converter measurements with a fixed or external heterodines*Built-in thermostatic YIG preselector*High measurement speed*Extend the NFA solution up to 50 GHz with special downconverter unit*SCPI Language Compatibility
-
product
Phase Noise Measurement Solutions
Keysight offers dedicated phase noise measurement solutions to simplify your measurements and maximize your efficiency. Building on 30 years of low phase noise and RF design and measurement experience, our innovative solutions are designed to provide the most accurate phase noise data possible, and are economically tailored to fit your specific performance and application needs - now and well into the future.
-
product
Low Noise Amplifiers
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a wide range of applications but are primarily suited to communication systems including both Data-Link and Satellite Communications (Satcom) systems. Our new K-Band LNA operates over a 19.2 - 21.2 GHz with 1.3 dB Noise Figure at 25°C. It is configured with a waveguide input and 2.92 output connector all in a hermetic package.
-
-
product
Large Area UV Light Source
Model 30L
The OAI UV Light Source Grande is a large area collimated light source. The device is available with output power up to 10KW. Utilizing collimating mirrors, the UV Light Source Grande is a highly efficient UV light source intended for a variety of larger-scale applications.
-
product
Directional Source
BAS003
The BAS003 Source is designed to generate homogeneous sound fields using random noise in compliance with the following standards: Building acoustics (insertion loss, acoustic absorption area, etc: ISO 140-3, ASTM E90, ISO 140-5, ASTM E966). The BAS003 is typically used to generate a noise in a free-field for the evaluation of the transmission loss index of a façade. The available high-efficiency power amplifier, BAS002, is light and can be remotely controlled for easy use in the field.
-
product
Phase Noise Analyzer
NXA-26
This new NXA-26 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 26.5 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range. The NXA-26 combines over 25 years of Phase Noise Measurement Technology with an easy to navigate user interface. System operation requires minimal training that will have you making measurements in minutes.
-
product
Dual Mobile Comm DC Source w/ Battery Emulation, DVM
66319D
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.
-
product
Precision Source / Measure Unit (2 Ch, 100 FA)
B2902B
The Keysight B2902B precision source / measure unit (SMU) is a 2-channel, compact, and cost-effective benchtop SMU with the capability to source and measure both voltage and current. It easily measures current versus voltage (I/V) with high accuracy. The 4-quadrant source and measurement capabilities enable taking I/V measurements without configuring multiple instruments.
-
product
Three-Phase AC Power Source 320 Vrms, 6 KVA, 5000 Hz
AC6906H
Keysight’s AC6900 Series three-phase power sources provide a complete AC and DC power solution by combining the capabilities of a multimeter, harmonic analyzer, and power analyzer in one instrument.
-
product
Low Power Programmable AC Power Source With Transients
Chroma Systems Solutions, Inc.
Equipped with a host of powerful features: power line disturbance (PLD) simulation, programmable output impedance, comprehensive measurement functions, waveshape synthesis and regulation test software
-
product
Noise Thermometer
MFFT-1
The MFFT-1 magnetic field fluctuation thermometer is a high accuracy thermometer system for typical dilution refrigerator temperature ranges.
-
product
Phase Noise Measurement Application
N9068A
One-button measurements for analyzing phase noise in frequency domain (log plot) and time domain (spot frequency)Compatible with phase noise measurement personality in Keysight PSA and ESA spectrum analyzers Runs inside the PXA, MXA, EXA signal analyzers and MXE EMI receiver
-
product
sbRIO-9375, Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781212-01
Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The sbRIO‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The sbRIO‑9375 offers isolation between the input and output banks from channel‑to‑earth ground. Non-enclosed modules are designed for OEM applications.
-
product
Long Life Seismic Energy Source
1900LLX-T
Output volume of 10 cubic inches to 250 cubic inches. Light weight enough for shallow draught vesselsPowerful enough for blue water seismic surveys. Available with engineered seals for more robust performance.
-
product
MP field sources calibration set
The MP field source calibration set is used to measure electric or magnetic fields in a frequency range up to 3 GHz. RF fields or transient fields can be measured. The MP field source calibration set is used to check fields of the Langer EMV-Technik GmbH field sources, fields of TEM cells and IC striplines.
