Dielectric Strength Testers
check insulation to assure current does not flow through it.
-
Product
Robotic ESD Tester
SmartZap
-
The SmartZap is a fully automated zap gun tester with automatic failure detection capability, providing far superior performance than manual zap gun test. It is complying IEC61000-4-2 test standard.
-
Product
Non-Contact Voltage Tester
NCVT-1
-
Non-contact detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets, and wires.High intensity, bright green LED indicates the tester is operational and aids in illuminating the workspace.When voltage is detected, a high intensity, bright red LED illuminates and a warning tone sounds.Discrete digitally controlled ON/OFF power button.Auto power-off feature conserves and extends battery life.Microprocessor controlled low-battery indicator and tester shutdown.CAT IV 1000 Volt safety rating provides expanded operation and protection.
-
Product
Leak Tester
AD-1690
-
Are you sure your pipettes are all accurate? Most pipette failures happen due to soiled or damaged parts compromising the airtightness of the pipettes. With the AD-1690 leak tester, you can instantly spot the pipettes that need to be fixed.
-
Product
Wire/Cable Harness Tester
PANTHER 4HT
-
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
Product
Crease And Stiffness Tester
DRK153
-
Shandong Drick Instruments Co., Ltd.
Whether this is by hand or by mechanical means. The crease recovery (spring back) can result in forces, which distort the erected carton or cause stresses to be applied to closures, which reducetheir effectiveness. With the Crease and Stiffness Tester, the Crease recovery is determined by the decrease in resistance offered by creased board after it is folded 90° at the crease measuring the recovery force after 15 seconds. Board Stiffness is determined by bending a 50mm length of board through a 15° angle.
-
Product
ESD Tester
GZ600 MIF
-
• Staff equipment tester with badge reader • Compact • LCD digital display • Identification by RFID badge • Allows communication with the company network or the dedicated server (SQL database)
-
Product
Electrical Testers
-
A range of professional-grade tools designed for electricians and HVAC engineers to safely test, measure, and diagnose electrical circuits.
-
Product
Current Transformer Testers
-
Vanguard Instruments Company, Inc.
Performs CT excitation, current-ratio, polarity, and phase angle testsMeasures insulation resistance and winding resistance of the CT seconday windingsMeasures the CT's secondary burdenTest record header information including company, substation name, circuit ID, manufacturer, CT serial number, operator name, and test record-commentsBuilt-in 4.5-inch wide thermal printerPlot Multiple Saturation CurvesStores up to 128 CT test plans and 140 test records internallyUSB, Bluetooth, and USB Flash drive interface
-
Product
Solderability Tester
ZHX-35
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008/IEC60851-4; Inspection standard: JB/T4279.14-2008Used to detect the self-solderability of enameled round wires and wire harness;Set variable temperature range and automatically maintain constant temperature;Under mechanical driven, samples would be withdrawn by the action of automatic insertion and lateral movement, free from vibration and noise;
-
Product
Flying Probe Tester
FA1817
-
Flying Probe Tester FA1817, an automatic testing system designed to inspect printed wiring on bare boards. The FA1817’s features and capabilities make it ideal for use in inspecting high-density printed wiring boards. With support for a broad range of test types, from low-resistance measurement to high-insulation-resistance measurement, the system reliably detects the latent defects that trouble end-users.
-
Product
Ross Flex Tester
UI-FT27
-
Ross flex tester is used to test the cut growth in rubber vulcanizates under continuously bend flexing in 90°.
-
Product
Electrical Testers
-
Regardless of what your trade requires, Klein Tools has an electrical tester for the job. With non-contact testers as well as outlet and receptacle testers, there’s guaranteed to be the tool for your jobsite needs. All Klein’s testers are engineered for ease of use and to stand up to the tough jobsite conditions encountered by professionals every day.
-
Product
Ground Grid Tester
GGT Series
-
The GGT500 ground grid integrity tester is designed for inspection of the substation ground grid. It can also be used as a portable micro-ohmmeter with Both Sides Grounded and Remote Control functionalities. It is intended to inspection the conditions of a grounding system beneath substations, testing of medium- and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links.In the United States when inspecting the quality of the grounding systems beneath a substation, the proper procedure is to inject 300 A DC during a time period of 60 s. This is what the GGT500 will do, and in that time period, the current path and voltage drop are checked. Also acting as a micro-ohmmeter, the GGT500 can test low resistance values by producing high test currents of up to 500 A.The instrument is placed in an unbreakable, plastic case with IP67 protective rating (with closed lid). Although very portable and lightweight, micro-ohmmeters have very high output power capabilities. High output voltage enables a wider measurement range at higher test currents, as well as the use of thinner/longer test cables. GGT500 ground grid integrity tester generates a true DC ripple-free (less than 1 % ripple) current with automatically regulated test ramps. This significantly decreases magnetic transients and ensures great accuracy.When used for testing in Both Sides Grounded conditions, a special current clamp powered from the ground grid integrity tester is used for measuring a current through groundings. If even a higher safety level is required, the remote control feature enables the operator to perform measurements from a distant location, away from the instrument and test object.
-
Product
Mechanical Hydraulic Tester
RFIK
-
The RFIK mechanical hydraulic tester provides the ideal solution for servicing and commissioning hydraulic circuits on agricultural and other mobile machinery. The kit comprises of a direct acting flow indicator with built in thermometer, a loading valve and a pressure gauge all built into a strong steel case with a removable lid.
-
Product
DC Resistance Tester
GDZRS-20A
-
GDZRS series Winding DC resistance tester is optimal designed for measuring three phase winding DC resistance of big capacity transformer. It can test three phase winding DC resistances at the same time
-
-
Product
Incline Impact Tester
-
Evaluates the ability of the packaging system to withstand sudden horizontal impacts or crushing forces.
-
Product
DMX Tester Portable
DTR-HH
-
The DTR-HH is a DMX 512 tester data send / receive unit with 10 store and recall preset scene snapshots. Each of the 10 presets will store 512 channel levels including the packet size and start code. Each preset can be edited to precise values and recalled anytime.
-
-
Product
Zipper Reciprocation Tester
UI-FT34
-
Zipper Reciprocation Tester is used to test zipper fatigue resistance under lateral and longitudinal tension.
-
Product
Insulation Testers
AD-902
-
The instrument is designed for the direct measurement of insulation resistance of cables and electrical equipment especially in the telecommunications and communications. It can also serve as a tester for example go. Circuits or connectors.
-
Product
Torque Tester
TorqueLab® LTT-Series
-
The torque analyzer is designed for calibrating tools, joint testing, auditing and measuring torque. Torque tools go out of calibration with use. To maintain consistent accuracy, torque tools must be checked periodically for wear or defective parts. A power or hand torque tool is a measuring tool that must be properly calibrated and maintained.
-
Product
Hipot Tester
19070
-
Chroma 19070 series are the smallest Hipot Testers currently available in the world. Its super mini size is easy to carry and the large LCD display is suitable for viewing measurement results. These sophisticated hipot testers are most applicable to safety test for electronic components.
-
Product
Martindale Abrasion Tester
GT-KC13A
-
To determine the abrasion resistance of all kinds of footwear vamp material. Samples are rubbed against known abrasion at low pressures and in continuously changing directions and the amount of abrasion. The unique design allows removal of individual sample holders for examination without lifting the top motion plate.
-
Product
Module Breakage Tester
-
King Design Industrial Co., Ltd.
1. Destruction System Hardware: *est rack system: support, shielding cover, crane & fixed wall. *Hit bag: FRP bag; 45kg of No.7.5 lead pills; hook, sleeve and hoisting ring. *Attachment: electronic scale, stopwatch, digital caliper
-
Product
Fabric Drape Tester
TF118
-
TESTEX Testing Equipment Systems Ltd.
Fabric Drape Tester, to measure and calculate the coefficient of drape by tracing a shadow of the draped fabric on paper. Fabric Drape Tester complies with BS EN 9073, BS 5058, ERT 90-1, etc.
-
Product
Electric Safety Tester
PVCHECKs
-
The multifunction device PVCHECKs allows quickly and safely carrying out the electric safety tests provided for a PV system (section in DC) and the functional test of modules/strings the system consists of according to the requirements of Standard IEC/EN62446.
-
Product
SMD Testers
-
Is a miniaturized and integrated utility model measuring instrument, which can automatically identify components such as resistance, capacitance, diode, etc., with LED, voltage regulator, DCV, on-off and battery power measurement functions. SMD resistance, capacitance, diode (RCD) parameter measurement, is a good helper for electronics factories and electronics maintenance.
-
-
Product
Automatic Relay Tester
-
The protective devices such as relays, overload coils, circuit breakers must be checked regularly to ensure that, they are always ready to operate correctly. If a fault occurs in the equipment, which they are protecting, routine relay testing will quickly detect the faulty, incorrectly adjusted protection circuits correctly. It is usually necessary to measure its operating time. The micro controller based time interval meter is used for this purpose in all AJIT brand relay testers.
