-
Product
AWD Dynamometers
MD-AWD-800
-
Mustang designed the MD-AWD-800-DE-24×2 Series to be a dyno that could be easily adapted to fit virtually any testing scenario without ever having to compromise. In AWD mode, the 800 Series XL can test AWD vehicles with wheelbases up to 134” long, enough to handle Hummer H1s. In 2WD mode, the 800 Series uses a single 24” diameter roller with a low base mechanical inertia to allow you to test the lightest vehicles out there.
-
Product
Chassis Dynamometers
-
With Chassis Dynamometers, it’s all about getting the best value – proven performance, durability and expert support long after your purchase. Taylor’s comprehensive line of chassis dynamometers supports testings for: performance, diagnostics, break-in, research and development, education and training.
-
Product
Chassis Dynamometers
-
Is a device used for vehicle testing and development. It uses a roller assembly to simulate a road in a controlled environment, usually inside a building.
-
Product
Heavy Duty Dynamometers
MD-7500-HD
-
Today’s Fleet Managers are faced with many challenges – most important of which is maintaining a healthy bottom line. With fuel costs at an all-time high, these challenges have become increasing difficult. Fleets being transitioned from fossil fuels to electric propulsion also face challenges with durability and range to make sure routes can be completed on time each and every day. To help combat these problems and others facing fleet managers today, Mustang Dynamometer offers the MD-7500-HD Series Chassis Dynamometer – which features the most advanced diagnostic capabilities in the industry. The MD-7500-HD is designed to simulate the driving conditions that fleet vehicles encounter on the road every day in a safe and controlled shop floor environment so that critical engine and drivetrain systems can be evaluated to insure vehicles are performing properly and at maximum efficiency. What’s more, the MD-7500-HD offers several levels of testing capabilities in a modular, compact package and with capabilities that can be upgraded in the future as your needs change. Every vehicle in your fleet can now be tested and validated before and after a repair to ensure proper diagnosis and repairs have been performed. In addition to testing repaired vehicles, the MD-7500-HD can be used to test vehicles on a regular basis as a preventative maintenance measure which decreases unexpected breakdowns and allows fleet management to control fuel costs while reducing repair costs. Periodic testing keeps fuel consumption to a minimum and helps technicians identify suspect components before they fail. A proactive approach to Fleet Service can prevent unexpected engine and or drive-train failure which saves organizations thousands of dollars in lost fair revenues. At the heart of the MD-7500-HD is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) – more than enough to simulate a fully loaded transit bus. As the systems PAU’s (brakes) are air-cooled, no water is required to or from the device – eliminating the high cost of water consumption and/or the cost of an expensive water recovery system – which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements. AC Motors can be added to simulate regeneration and validate range for organizations that have transitioned to carbon free electric propulsion. The 7500 is the best solution for fleet managers looking to improve their bottom line and offer disruption-free public transportation.
-
Product
Emissions Dynamometers
MD-100-M-CDMX
-
Las altas demandas de producción requeridas para los programas de inspección de emisiones vehiculares requieren del uso de equipo robusto, confi able y duradero para este propósito. Diseñado desde un principio para soportar altos niveles de uso y el abuso, Mustang Dynamometer ha establecido los estándares de desempeño para equipos fabricados y usados a nivel mundial en los programas de inspección de emisiones. Al ser pioneros, nuestra experiencia nos ha llevado a ser el líder mundial en el diseño y fabricación de equipo robusto y programas informáticos para la industria de Inspección y Mantenimiento (I/M). Contamos con líneas de prueba instaladas alrededor del mundo en climas que varían de frío a cálido y de húmedo a seco, incluyendo condiciones extremas. Para fi nales del año 2020 estimamos que nuestros equipos instalados habrán realizado pruebas en cerca de 1 billones de vehículos. Mejoras continuas en todos los aspectos tecnológicos nos han llevado a desarrollar soluciones innovadoras basadas en nuestro amplio conocimiento del diseño, servicio, mantenimiento, ergonomía y capacidad funcional. Los equipos Mustang para Inspección y Mantenimiento (I/M) están diseñados para cumplir con las necesidades específi cas de nuestros clientes. Cumpliendo con las siguientes especifi caciones: EPA, BAR y CDMX ASM.
-
Product
AWD Dynamometers
MD-AWD-500
-
MD-AWD-500. Mechanically linked AWD performance dyno. The key to designing an AWD dynamometer properly is to understand the methods currently being used by manufacturers in the field of AWD drivetrain technology. A dynamometer that can accommodate various types of AWD vehicle transmissions and wheelbases without excessive complication and, more importantly, without risking damage to a client’s AWD system is paramount.
-
Product
Engine Dynamometers
-
SuperFlow manufactures water brake, eddy current and AC engine dynamometers for performance and industrial applications. SuperFlow engine dynos test gasoline, diesel and CNG engines and several of our water brake dynos are used for AC motor testing.
-
Product
Water Brake Engine Dynamometers
DX Series
-
Over 2,000 facilities worldwide count on the durability of Taylor Dynamometer’s DX Series Water Brake Dynos. On every continent, and in more than 50 countries, you’ll find a DX – often one that’s been in operation for over 30 years.
-
Product
2WD Dynamometers
MD-800 Series
-
For instances where a performance shop is interested in performing basic dynamometer runs for peak power measurement and overlapping multiple runs to quantify performance gains or losses resulting from changes to the vehicle, the MD-800 offers the perfect combination of competitive pricing and performance capabilities as an inertia-only dyno, while allowing an easy upgrade path to add power absorption when you are ready to offer professional steady-state tuning services. Once added, the eddy current upgrade allows for steady state tuning of high performance EFI vehicles via a 900-hp power absorber module.
-
Product
Chassis Dynamometers
-
Eddy current, Water brake and AC motoring chassis dynamometers for dyno testing heavy-duty on and off-highway vehicles.
-
Product
Chassis Dynamometers
VULCAN Series
-
The high-precision chassis dynamometer VULCAN series is suitable for testing Light-Duty-Vehicles (LDV), Medium-Duty-Vehicles (MDV), Heavy-Duty-Vehicles (HDV) as well as 2-3 wheelers and ATVs. Available as either a two-wheel or a four-wheel drive set-up, HORIBA chassis dynamometers are suitable for electrified mobility with an improved energy efficiency of up to 97% efficiency. Equipped with the synchronous motor technology in each individual roller, they also cover technical requirements in high-performance ranges and allow a significantly better torque distribution when it comes to electrified vehicles.
-
-
Product
2WD Dynamometers
MD-1100 Series
-
The MD-1100 Series took the market by storm in 2003 when it was first introduced and has been a mainstay in the performance industry ever since. The design focus for the MD-1100 is, in a word, versatility. The MD-1100 offers a tremendous amount of power measurement capabilities, loading capabilities and mechanical versatility found nowhere else in the business. Regardless of your needs, the MD-1100 series is a perfect fit.
-
Product
Portable Dynamometers
-
With the Portable MD-AWD-500, you have a portable drag strip that can handle just about any 2WD or AWD car on the street. Equipped with a drag racing timing system, multiple displays, and Mustang’s DragSim software, the portable MD-AWD-500 is sure to draw large crowds where ever it appears. One thing is for sure, a dyno draws big crowds when it shows up at an event. There is something about watching the wheels spin and listening to an engine at full throttle that captures people’s attention. Add to that actual drag racing times, reaction time results and a virtual animation of the car racing down the strip or street and you’ve got yourself some serious racing entertainment. Mustang’s top-of-the-line portable chassis dynamometer is the Portable AWD-500 Series dynamometer. No other dyno offers all of the benefits of a Mustang AWD-500 dyno in such a tightly-engineered portable package. Mounted inside of a flatbed trailer, the portable AWD-500 is easy to trailer to and from events and can be set-up by a single operator. This is the ultimate portable dyno. Great for promotional events, dyno sharing arrangements or as a traveling dyno for trade shows or car show events. Like the standard AWD-500, the portable version can test both AWD and 2WD vehicles and can switch back and forth with a simple click of the mouse. With added displays, a drag racing timing system and Mustang’s DragSim Software and you’ve got yourself a portable drag racing strip that is dead nuts accurate, extremely repeatable and a real crowd pleaser. Portable AWD-500 Features Include:
-
Product
Water Brake Chassis Dynamometers
-
Chassis water brake dynos (also known as hydraulic dynamometers) can be operated continuously to resolve overheating, fuel mileage and drivetrain issues. Taylor’s eight models accommodating 50 to 1,100 hp at 40 mph enable testing of single-axle diesel pickup trucks, RVs and buses up through the largest tandem-axle on-highway trucks and buses. Tap into our deep product and applications knowledge to help you choose and make the most of the right water brake system for current and future needs.
-
Product
AWD Dynamometers
-
Full time AWD vehicles are designed to provide maximum performance regardless of road conditions. In cases where traction is less than ideal, a vehicle may be designed to improve stability and traction at the expense of power. This means adding torque to a spinning wheel or retarding of timing. In order to properly test an AWD vehicle for peak performance, an AWD chassis dynamometer must be able to simulate ideal road-load conditions to the vehicle. This approach allows the vehicle to be evaluated under "optimum" operational conditions; whereby torque is distributed to the vehicle's tires in the same manner that would normally occur when a vehicle has equal traction at all four drive wheels, and is therefore operating at peak efficiency.
-
Product
Water Brake Engine Dynamometers
Hydraulic Dynos
-
Ideal for a wide range of markets, water brake engine dynamometers churn water inside the housing and transfers energy by momentum exchange and water shear. The more water flowing through the dyno, the greater the braking force exerted on the device under test.
-
Product
Agricultural PTO Dynamometers
-
An agricultural PTO dynamometer measures PTO power output. Power, torque, and RPM can be controlled and measured without reliance on water.
-
Product
Eddy-Current Dynamometers
WB Series
-
Eddy-Current Brake Dynamometers (WB Series) are ideal for applications requiring high speeds and also when operating in the middle to high power range. Eddy-Current Brakes provide increasing torque as the speed increases, reaching peak torque at rated speed. The dynamometers have low inertia as a result of small rotor diameter. Brake cooling is provided by a water circulation system, which passes inside the stator to dissipate heat generated by the braking power. The water cooling in the WB provides high continuous power ratings (max. 140 kW). The WB dynamometers have accuracy ratings of 0.3% to 0.5% full scale ( 2% for WB 2.7), depending on size and system configuration. Additional options include: high-speed version, speed pickup, mechanical rotor blocking device, OEM version IS and vertical mounting.
-
Product
2WD Dynamometers
MD-600 Series
-
The MD-600 is capable of measuring 2,000 horsepower and a top speed of 200-mph. A single eddy current PAU gives this dyne 900-hp of braking, while adding another PAU doubles this to 1,800-hp of loading capacity for steady state tuning and loaded mode testing.
-
Product
Portable Engine Dynamometers
-
Cost-effective Portable Engine Dynos from Taylor Dynamometer are water brake style systems for diesel applications up to 1,250 hp (932 kW) and 3,000 ft-lb (4,068 N) of torque. Mount yours right on the engine in minutes for fast, convenient and reliable testing.
-
Product
Transmission Dynamometers
-
SuperFlow’s Axiline and Hicklin transmission test stands cover the complete range of light-duty, medium-duty, heavy-duty and cross drive transmissions on the market today. With solutions for everything from passenger cars to the M1 tank and features like mechatronic shift controls, no-hassle precision aligment tooling and the available PowerNet Data Acquisition and Control system for fully automated tests and reports, SuperFlow transmission dynos are the only choice of the top transmission remanufacturers world wide. Check out or custom testing solutions page for examples of custom transmission test stands we’ve built for heavy duty cross drive dynos and full AC regenrative test stands.
-
Product
Heavy Duty Dynamometers
MD-250-HD
-
The MD-250-HD series dyno (SE/DE) was designed to be a performance dynamometer first with the added benefit of being able to test 2-wheel-drive heavy-duty vehicles such as truck, buses and commercial vehicles in addition to the standard car or light duty pick-up. The 250-HD is certified in the states of Colorado, Nevada and Utah for use in loaded-mode diesel smog testing programs because of its accuracy and reliability. No other dyno in its class offers more value or better in-house motor vehicle testing capabilities than the Mustang MD-250-HD. For starters, the MD-250-HD boasts a 1,500 horsepower measurement capacity at a top speed of 175 mph and a powerful air-cooled eddy current brake provides the MD-250-HD-SE with 900-hp worth ofloading capacity for steady state testing. Loading capacity can be increased to 1,500-hp via the optional DE model. The 250-HD can be upgraded to the 250-HD-SE-M via the addition of a 100 or 200 hp AC motor for transient testing of electric buses to measure range and regeneration or for emissions testing of IC engines. Do not be fooled by its compact size – the MD-250-HD is a serious dynamometer with serious tuning capabilities. The MD-250-HD uses a powerful eddy current power absorber, a frictionless, air-cooled braking device, to enable it to apply variable and steady state loading. A complete control and data acquisition system lets you design a wide range of tests or select from a host of pre-configured tests included with the standard system. The 250-HD’s four roller design makes setting up vehicles a snap – simply drive onto the 250-HD and let the tires settle in between the rollers. The 250-HD can be installed above-ground or below-ground, it’s your choice. The above-ground system utilizes an optional premium platform and ramp system with an above-ground restraint kit. The addition of an axle pull-down kit help keep the tires from slipping or trying to “climb out” of the rollers.
-
Product
Multi-Purpose Brake Dynamometers
GIANT 6000 Series
-
The GIANT 6x00 product line is a multi-purpose, full-size inertia brake dynamometer for performance and NVH tests of brake systems from passenger vehicles to truck brakes, commercial vehicle assemblies and high-speed railway applications. The GIANT 6x00 product line offers a complete range of test functions for fully automated performance tests and basic NVH investigations and can be designed to fit the requirements of our customers.
-
Product
Cycle-ATV Dynamometers
EC997
-
The EC997 Series, our standard eddy current motorcycle chassis dynamometer, takes motorcycle performance tuning to the next level. The EC997 Series uses the industry’s most advanced electronics and Dynamic Load Control technology, featuring precision closed-loop torque feedback – a standard feature with every EC997 dyno. Competitor’s dynos on the market allow you to apply “percent % load” but Mustang has perfected the art and science of Dynamic Load Control and proudly offer the most sophisticated Dynamic Load Control dynamometer available at any price. Our superior control technology combined with our ultra-low inertia design allows you to precisely control loading to hold the engine at each RPM. Try doing that with a heavy drive roller and insufficient control technology – you simply cannot! Mustang has delivered thousands of performance dynamometer systems over the past 35 years and has perfected the art and science of dynamic vehicle loading and dynamometer control. We include each motorcycle make and model in our database including weight and drag coefficients so you can simulate the track right on the dyno! While other dyno manufactures are still trying to catch up with our technology, Mustang continues to lead the industry and is recognized around the world as the industry’s best with regards to dynamic dynamometer controls. Mustang has built racing dynos for Harley-Davidson as well as several end of production line testing cells for Harley-Davidson, Honda, and Polaris.
-
Product
Portable Dynamometers
MD-500
-
The 500 series 2WD dynamometer is a high horsepower dyno that lets you tune street cars without a large dedicated space. The 500 portable includes a pallet jack modification on one end of the frame and two bottle jacks on the other allow you to move this dyno in your shop. The portability kit lets you free up space as needed. The portable 500 is ideal for smaller shops, schools and outdoor events. There is no need to secure the unit to the ground – simply lower the unit onto the ground, hook up the aluminum ramps and start testing.
-
Product
Froment Dynamometers
-
Froment Sigma Dynamometers test, prove and exercise agricultural tractors and self-propelled machinery with maximum efficiency and with the minimum waste of time and fuel. Testing is quick, accurate and simple to carry out, with a choice of automatic or manual test modes.
-
Product
Engine Dynamometers
-
Water brake, Eddy current and AC dynamometer systems for heavy-duty diesel, gaseous and gasoline testing applications from 20 through 10,000 HP.
-
Product
Emissions Dynamometers
MD-1000-M
-
The MD-1000 sets the industry standard for heavy duty chassis dynamometers due to its rugged design and accurate loading capabilities. Simulate on-highway driving conditions under real world loads. Adjust loading to simulate a host of in-use operating conditions. The 1000 is approved for use in Nevada and Colorado for Diesel Smog Testing.
-
Product
Eddy Current Chassis Dynamometers
-
Cradle- or single-roll (top-mount) dynamometers accommodating single- or tandem-axle vehicles, with continuous vehicle power ranges from 50 hp to 622 hp (37 kW to 464 kW), Taylor’s chassis dynamometers allow a top recommended speed of 90 mph (145 kph) at full load. Look to our experts to not only help you select your optimal system, but also to provide design, configuration, installation and training for a total solution that integrates seamlessly with your operation.
