-
Product
Modular Power
RFP Chassis
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
Mini MUTT Portable Trailer Tester
#9003A
-
Innovative Products of America
portable trailer tester for testing lights and electric brakes on light-duty type trailers (7 spade, 6 round, 5 and 4 pin). The Mini MUTT places a load on the trailer's electrical circuits to verify proper lighting function. The Mini MUTT is powered by an (optional) internal 12v battery,
-
Product
PXI Hex 4:1 High Voltage Power MUX
40-331-004
Multiplexer Module
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
Product
AC/DC CAT IV 600 A TRMS Navigator Clamp Meter
ACDC-52NAV
-
The ACDC-52NAV clamp-on power meter is the ideal choice for jobs that require AC/DC current measurements to 600 A, AC/DC voltage to 1000 V and wide jaws to accommodate large conductors.
-
Product
Small Full Safety Insulated Crocodile Clip
126017/Colour
-
IEC 1010 Rating: 300 Volts CAT II Double/Reinforced Insulation 10Amps Standard Colours: Black, Red, Green, Blue, Yellow, White Features: Will accept all standard 4mm plugs.
-
Product
Infiniium MXR B-Series Oscilloscope: 2 GHz, 8 Channels
MXR208B
Oscilloscope
MXR208B Infiniium MXR B-Series, 2 GHz on all 8 channels, option to integrate 8 instruments in one, hardware accelerated plotting, and fully upgradeable , including up to 6 GHz.
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-K
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
RF and Microwave USB Programmable Signal Generators
LSG Series
-
The Lab Brick LSG series of low cost USB-compatible RF and microwave signal generators covers frequencies from 20 MHz to 6 GHz with high output levels and excellent spectral purity. They require no additional DC supply voltage and offer several operating modes, including continuous-wave (CW) and swept-frequency. GUI software can track and control several connected signal generators, simplifying multiple-signal test setups. Each device stores settings in internal memory, allowing it to power up in a specific instrument state.
-
Product
Check It! Gas Analyzer
F-920
-
The F-920 Check It! Gas Analyzer is a device that rapidly measures CO2 and O2 from 0-100%. Designed for QA personnel to take precise and speedy measurements of CO2 and O2, the Check It! displays results in less than 6 seconds and has a sampling volume of 6.5 mL.
-
Product
LXI Microwave Multiplexer, SP4T, 6-Bank, 67GHz, 50Ω, SMA-1.85
60-803-806
Multiplexer Module
Our 60-803-806 is a 6 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI Strain Gauge Simulator Module 6-Channel, 1.5k
40-265-406
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 1.5kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
COM-Based SBC with WL8665UE CPU / COM Express Carrier
GEMINI
-
GEMINI is a COM Express Compact type 6 carrier board and SBC with PCI/104-Express I/O expansion. Feature-rich GEMINI offers the highest performance in a compact 4.0 x 4.0' / 102 x 102mm size, with its combination of COM Express CPU module and full support for PCIe/104 type 1 connectivity (PCI-104 up to 4 modules, PCIe-104 x1 up to 4 modules, and PCIe/104 x16). Gemini is designed to support a variety of COM Express modules including Bay Trail, Apollo Lake to Core i7 8th generation and Xeon.
-
Product
Modular Matrices
-
Modular Matrices include two ranges: - The LDX+ range provides a cost effective modular solution for budget sensitive projects requiring fewer advance features at shorter Cat 6 cable lengths of up to 70m.- The MDX+ range incorporates the videowall processor technology which allows a number of output blades to be grouped together to form a multi display video mosaic or wall. This feature is available for the HDBT, DVI, 3G-SDI and fibre output cards.
-
Product
Phase Sequence Indicator
PHS 863
-
Two Functions in one unit including open phase and phase sequence. Large Size alligator clips can easily clip on switch-board terminal. Highly Reliable : Identifies 3 phase sequence and open phase check. Functional design : This model is ideal for installing conveyor lines, pump systems and interconnected drivers. Safety approval : CE marks EN 6101-1 CAT. III. EN 61010-2-031
-
Product
Multi-Channel Attenuation Control Unit (4-channels), DC to 6 GHz, 0 to 121 dB, 1 dB Step
J7204A
Attenuator
The J7204A is a multi-channel (4-channels) attenuation solution for signal attenuation and conditioning of up to 4 devices under test (DUT). Operating frequency from DC to 6 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7204A reduces cost of ownership and provide the best measurement accuracy.
-
Product
Coaxial Attenuators Set
11583C
Attenuator
The Keysight 11583C contains a set of four 8493C attenuators 3, 6, 10, and 20 dB furnished in a handsome walnut accessory case. The Keysight 8493C are APC-3.5 connectors with a maximum frequency of 26.5 GHz. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
Product
6 Chip Detection and Burn Channels
CD1
-
The CD1 provides 6 Chip Detect and Fuzz Burn interface(s). A Chip Detector (CD) is a magnetic-electrical device that provides a reliable method of detecting impending failure of bearings and gears.
-
Product
PXI Solid State Switch Module, 6xSPST, 10 A
40-182A-011
Switch Module
The 40-182A-011 has 6 off high current SPST switches in two PXI slots and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
Handheld Water Quality Meters
LAQUA PH220
-
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers) - 0.01 pH resolution- Offset and average slope display - Automatic / manual temperature compensation and temperature calibration function- ORP calibration option- °C & °F temperature readings- With real-time clock and date/time stamp for GLP compliance- Auto log data; built-in memory can store up to 1000 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached- Monochrome LCD with white LED backlight: 50 x 50 mm- Phono jack output for connecting meter to computer via PC (USB) cable for data collection and to printer via printer (RS232) cable for printout - Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrode and calibration solutions in carrying case- 3 years meter warranty
-
Product
Cable Assembly, Receiver, Tripaddle, 36”, 6 9-PIN DSUB
540352010201
Cable Assembly
Cable Assembly, Receiver, Tripaddle, 36”, 6 9-PIN DSUB
-
Product
Testability analysis
-
Using TestWay, ASTER provides advanced Testability report, Rules checking for In-Circuit Test, Functional Test and Boundary-Scan test. Test point optimization – Up to 70% of test points saved, automated backannotation to CAD system and CAD/CAM/CAT tools.
-
Product
RF SPDT PXI Switch Modules
-
Pickering's RF SPDT PXI Switch Modules are capable of providing economic switching for frequencies up to 6 GHz. Our other PXI RF options include RF matrices and RF multiplexers. For higher frequency applications or applications requiring high performance levels, please take a look at our microwave switching modules.
-
Product
TRMS AC/DC Clamp-on Power
HT9023
-
HT9023 has been designed to measure AC, DC AC+DC current up to 1000A in TRMS reaching CAT IV 600V and CAT III 1000V in compliance with safety standard IEC/EN61010-1. The clamp also measures DC voltage up to 1500V, AC, AC+DC voltage up to 1000V, Active, Reactive and Apparent Power, Power Factor, Energy, voltage/current harmonic analysis up to the 25th with THD% calculation in balanced single-phase or three-phase systems.
-
Product
NIST Calibration for D610-A
D610-A-CCNIST
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
4G Router
ICR-2834GPA02
-
ICR-2800, EMEA, 2x Ethernet, 2× RS232/RS485, USB, GPS, Plastic, UK ACC LTE Cat.4 with 3G/2G fallback. GNSS receiver 1.3 GB eMMC storage to host customer SW applications 2× SIM with cover, eSIM ready.
-
Product
Ethernet/LXI digitizerNETBOX 16-Bit Multi-purpose Digitizer - 5 MS/s on 8 Channels
DN2.591-08
Digitizer
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Three-Phase AC Power Source 320 Vrms, 6 KVA, 550 Hz
AC6906L
-
Keysight’s AC6900 Series three-phase power sources provide a complete AC and DC power solution by combining the capabilities of a multimeter, harmonic analyzer, and power analyzer in one instrument.
-
Product
NI-9476, 36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module
780175-01
Digital Module
36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module - The NI‑9476 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 36 V, based on the external power supply, and features transient overvoltage protection between the output channels and the backplane. You can programmatically monitor the built-in overcurrent and short-circuit protection status of each channel.
-
Product
4G Router
ICR-2734W
-
ICR-2700, EMEA, 2x Ethernet, USB, Wi-Fi, Metal, Without Accessories LTE Cat.4 with 3G/2G fallback. 1.3 GB eMMC storage to host customer SW applications 2× SIM with cover, eSIM ready.
-
Product
PXI Strain Gauge Simulator Module 6-Channel, 3k
40-265-106
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
