Filter Results By:
Products
Applications
Manufacturers
Software
a set of instructions to run hardware and or process data.
-
product
Calibration Tool
Software
The smartGAS Calibration Tool is a commercial software company that makes it possible to interact with all smartGAS sensors of the EVO series with firmware version 5.17 or higher. With the smartGAS Calibration Tool, it can be read out and the zero point and the end point can be used with a suitable test gas.
-
product
Software
CaptivATE
Chroma Systems Solutions, Inc.
CaptivATE test software provides an electrical safety test solution for accurately performing automated hipot, leakage current and functional tests. Testing is made simple and fast by automatically downloading the test setup, conducting the required measurements and outputting the test results. Software supports IEC60601-1 test requirements and IQOQ protocol documentation.
-
product
ChromSquare GC×GC Software For Comprehensive Chromatography Data Analysis
ChromSquare
ChromSquare GC/GC is data analysis software for comprehensive gas chromatography (GC/GC). ChromSquare provides easier, more reliable analysis of information obtained from GCxGC analysis, enabling everything from qualitative to quantitative analysis. This software is a product of cooperative research with a group headed by Professor Mondello at the University of Messina (Italy). This group implements cutting-edge research in the field of comprehensive 2D chromatography.
-
product
Carrier Board Design and Software Verification Computer-on-Module Starter Kit
Starter Kit - ETX
- ETX module of choice- CPU, Memory of choice- Thermal Solution (heatspreader, and heatsink) of choice- Reference Carrier Board- Schematics, Design Guide, and User Manuals- ADLINK USB Stick with Documentation, Software
-
product
High Frequency Antenna Analysis Software
XGtd®
XGtd is a general purpose ray-based electromagnetic analysis tool for assessing the effects of a vehicle or vessel on antenna radiation, predicting coupling between antennas, and predicting radar cross section (RCS). It is ideally suited for applications with higher frequencies or very large platforms where the requirements of a full physics method may exceed available computational resources.
-
product
IQ Test Team Edition
McCabe
McCabe IQ Test Team Edition provides comprehensive test / code coverage to focus, monitor, and document software testing processes. Using industry-standard testing methods and advanced dynamic analysis techniques, McCabe IQ Test Team Edition accurately assesses the thoroughness of your testing and aids in gauging the time and resources needed to ensure a well-tested application.
-
product
Particle Analyzers
Teilch Particle Analyzers have proven significant advantages when compared to competitors’ solutions. Innovations in light source, flow control, analog and digital signal processing, components integration and software allow Teilch to provide a state of the art system for precision particle analysis.
-
product
Software
Megger offers a complete range of software for the certificating contractor under the name PowerSuite®.
-
product
Flex and Software Products
FLEXSTAND is a simple to use and flexible interface that significantly reduces the development time of operator interfaces requiring only basic programming skills. By using FLEXSTAND you can create simple or advanced operator interfaces in hours instead of weeks. A specially designed interface (API) hides all the complex TestStand properties and methods that usually make the task of creating operator interfaces difficult. Dynamic Operator interfaces can easily be created that change the User Interface to the task being performed. Not only that the product automatically adjusts the size of the user Interface to fit the size of the LabVIEW™ front panel.
-
product
Data acquisition software RSIC for force gauges Centor
RSICW-C
With the RSIC data acquisition software, you can record hte measurements of your gauge Centor directly using MS Excel. It makes it easier to record results and ensure traceability and processing; these are the main advantages for using this simple yet powerful software.
-
product
SMX Series
The SMX series is an extension of VTI’s award-winning EX1200 series switch family. Designed using the same core philosophy of high-density without compromising on performance, the SMX brings instrument grade switching capability to PXI Express for the first time. Our SMX switch cards encompass everything from power switching to the widest range of microwave switching in the PXI platform. Our drivers and support software provide standard operation in Windows, Linux, and LabView but add additional capability through our award winning GUI.
-
product
Electromagnetics
Altair software is used across industries to solve a broad range of electromagnetic problems from static to low and high frequencies. Whether your application requires multiple frequency and time-domain techniques with true hybridization to enable efficient exploration of a broad spectrum of electromagnetic performance, or the simulation of magneto static, steady-state and transient conditions, we have the tools you need.
-
product
Pyrometers
METTLE Series
Nagman Instruments & Electronics Pvt. Ltd
METTLE Series Infrared pyrometers are high performance and intelligent, with built-in stainless steel (SS 304) casing and high reliable circuit design (low temperature drift, full digital measurement design, ambient temperature compensation, real-time signal processing, software code optimization) to meet critical application environments.
-
product
LTE/LTE-Advanced Multi-Channel, Reference Solution
Gain greater insight faster with a compact, multi-channel LTE-A PXI signal generator and signal analyzer reference solution.This Reference Solution uses world-class Signal Studio software to create complex LTE-A waveforms and the 89600 VSA/WLA software to connect to multiple analyzers. The VSA software allows engineers to quickly view multiple antenna elements simultaneously and analyze the RF performance and modulation domains for timing and signal quality issues in complex carrier aggregation and MIMO/beamforming designs.
-
product
Control/Gateway/Display All-In-One Industrial Panel PC
PanKonix Series-HMI Panel PC
The PanKonix® series HMI is an Intel® Core™ i3/i5 and Intel Atom® x5/x7-based panel PC equipped with user-friendly, full-featured HMI software. It ensures seamless PLC connectivity through Modbus protocol support and incorporates trend charts, data logging, alarms, and cloud connectivity functions with RESTful API, MQTT, and OPCUA support for efficient data visualization and machine monitoring.
-
product
PXI Bus Expanders
MXI-4 Series
The MXI-4 PXI Bus Expanders allow direct control of PXI systems from any PCI slot in a desktop computer or server. MXI-4 interface cards can also be used to link multiple PXI chassis. MXI-4 technology utilizes a high-bandwidth link that is transparent to software applications and drivers, therefore providing the ability to use high performance desktop computers or servers to control PXI systems.
-
product
Electromagnet System
Electromagnet systems with different power levels to produce homogeneous magnetic fields. Usable for calibration of sensors, testing of magnet systems and Hysteresis measurement. Adjustable air gap from 0 up to 60 mm. Field strength in the air gap up to 3 Tesla. Software program for control and evaluation.
-
product
SNMP Client
The SNMP Client ‘SAMager-Console’ is a comprehensive Network Management System (NMS) software for operators, service staff and system engineers, especially suited to monitor Digital TV and/or Mobile DTV networks.
-
product
Light-Guided Connector Assembly | Cable & Harness Tester
CableEye Light Director System
Our Light Director™ system (patented) provides a computer-guided technique for assembling connectors used in aerospace, medical, and other high-reliability applications. This system uses light fibers driven by super-bright LED lamps to individually illuminate target cavities in the connector being assembled. When the technician enters the wire code printed on unconnected wires, or touches a wire connected at the other end, the CableEye software turns on the appropriate fiber, thereby causing a bright, flashing light to project from inside the target cavity guiding the technician to the proper insertion point. Correct insertion is confirmed by the elimination of light from that location, whereas insertion into an incorrect location leaves the flashing light visible.
-
product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 125 MS/s on 16 Channels, 80 MS/s on 32 Channels, 32 Single-Ended Inputs, 16 True Differential Inputs
DN6.596-32
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
product
Measurement
Vibration Meter
The input signal of the Vibration meter software, which is the output signal of the accelerometer, i.e. the vibrational acceleration signal, is filtered by means of one of four possible digital band filters. Then, based on this signal, vibrational velocity and displacement signals are calculated by means of integrating filters. Thus, the software generates three signals which are transferred to the ZETLAB data server virtual channels created by the program and having the word “Acceleration”, “Speed” or “Displacement” in their names, respectively.Signals are averaged for a selected time interval (0.1 s, 1 s, or 10 s), after which the obtained values are displayed in the dialog box elements of the Vibration meter program. It is possible to display a root-mean-square (RMS), average amplitude or peak value.
-
product
MountainsSPIP™ 8
We are currently working hard on a new development, together with our colleagues at Digital Surf *), to bring you the next generation of SPM image analysis software, based on the industry-standard Mountains platform and all the best SPIP interactivity and analytical tools.Our new product, called MountainsSPIP 8, will be unveiled at the MRS Fall Exhibit in Boston November 2018 and available for customers early 2019.
-
product
Inbuilt External Controller ATE with Touch Screen Features
QT 200NXT
Qmax Test Technologies Pvt. Ltd.
QT 200 nxT is a ultra modern stylish Inbuilt external controller ATE with touch screen features, is now available as a desktop unit with the cost, flexibility, and performance demanded by a large number of users in research, design, manufacturing, and repair & maintenance industry. It is a combinational-mixed signal board tester for PCBAs designed to cater the needs of PCB test and repair depots, keeping in mind the changing PCB technology and challenges in testing them offline with the combination of all such complex test methodologies in a single test hardware platform with simple to use graphical user interface software. The vast library support helps you to functionally test host of different IC families. Other features like user-friendly Windows based software, add-on utilities like oscilloscope, RCV meter circuit tracer, etc. makes it a favorite and makes very effective for repairing PCBs without schematic/ circuit diagrams. All these tests are carried out using simple BUT Interface like multipin test clips, probes or custom test fixture
-
product
Camera Testing
SWIR
CI systems' SWIR turn-key test stations simulates low light conditions to test special application cameras. An intuitive user friendly software carries out a variety of tests. The test stations are radiometrically calibrated to perform comprehensive SWIR tests.
-
product
Development Boards
Advantech Development boards provide a schematic software & reference to reduce design effort at the development stage. Development Boards have been designed in order to allow customers to verify the functions of COM, text carrier board problems and support COM series. Advantech has designed a Development Board which can be used to test carrier board problems and support COM series, and Qseven, ETX / XTX form factors.
-
product
Downloadable PAT Tester
Apollo 400+
The Apollo 400+ features a comprehensive range of electrical safety tests with user configurable test sequences and has storage for up to 2,000 test records. Compatible with our Seaward PATGuard 3 software for record keeping and reporting.
-
product
DC Vibration Unit Tester
BK2116
As the technology for BLDC motors advances, more advanced testing is also needed. The BK2116 DC Vibration Motor Tester was designed when of several of our clients needed to test the new generation of 3 port DC vibration motors. Using the BK2116, you can test the electrical specifications (RPM, current, drop pulse, and start up voltage) and also vibration level, and noise of motors with either 2 or 3 ports. The BK2116 can concurrently test 2 DUT's and BaKo's Test Shop software makes it very easy to set up and test. And because you use it with a PC or notebook, you can see graphs of the data as you test, and also save it to analyze later, or to analyze the data you gather over time.
-
product
Reel-to-Reel Options
Designed for automated inspection of reels of components to check for component authenticity. Includes GTI-4000 software to compare lead frames, die size and wire bonds of each part to your known good part. The software will identify any part outside the tolerance and save an image of each part.
-
product
Data Acquisition Software
Data System - DS
APEX Turbine Testing Technologies
From 4 to 400+ channels to support testing requirements. Networked architecture for flexibility and large channel counts. All channels can be synchronized. Multiple pages; multiple windows with no loss of plot data when changing pages.
-
product
Overhead Board
OVH-380-2
Curtiss-Wright Defense Solutions
The OVH-380-2 is the enhanced overhead board for the AIM/ HS-AVDAU-200XE. It stores and executes the operating system, application software and drivers, and terminates the IP stack for Ethernet support. It also receives and formats inbound (acquired) data.
