-
product
Circuit Breaker Analyzers & Timers
CAT circuit breaker analyzers and timers are advanced standalone or a PC controlled instruments for circuit breaker maintenance. Typical application areas of CAT instruments are medium and high voltage substations at electric power generation, transmission, and factories of switchgear. Also, industrial environments and electric power distribution are suitable application areas for these circuit breaker testing instruments.DV Power CAT circuit breaker testing instruments are portable and lightweight. They are designed for performing mechanical operations intended for circuit breakers testing according to standards IEC 62271-100 and IEEE C37.09.These instruments measure:the timing of main contacts, pre-insertion resistor contacts, auxiliary contacts operations,coil currents,motion parameters,voltage recording,main circuit resistance,arcing contacts wipe,and any relevant analog signal.Motion transducer channels provide measuring a displacement of the circuit breaker moving parts, contact wipe, over-travel, rebound, damping time, and average velocity. Even more, CAT circuit breaker analyzer optionally has a built-in micro-ohmmeter. Hence, it provides the main circuit resistance measurement and dynamic resistance measurement. Dynamic resistance measurement is an effective method for arcing contacts condition assessment.
-
product
PCI Express, IEEE 488 GPIB Instrument Control Device for Linux
779779-01
The PCIe‑GPIB is an IEEE 488 controller device for computers with PCI Express slots. You can use this device to integrate an instrument into your system using GPIB. The PCIe‑GPIB achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB. The PCIe‑GPIB includes a low-profile bracket option as well as a kit that includes the NI‑488.2 driver for Linux®. Regardless of which PCIe‑GPIB you purchase, the device is compatible with Windows, Linux®, and Mac OS X. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
-
product
Bench Top Test Set
WesTest-3000/BTTS
Communications & Power Industries
*PXI Based*Test Requirements Driven*Cost Capability Consistency*Software Standards- ATML, IEEE
-
product
Automotive Ethernet Rx Compliance Software
AE6910R
Unlike CAN, LIN, or MOST, the IEEE standard for automotive Ethernet demands rigorous compliance verification using specific test cases. The test requirements include complex measurements: vector network analysis with S-parameters, bit error rate (BER) test, and protocol analysis of high-speed digital signals.
-
product
Special / Customer Spec. Crates
6U VME64x 6023 JLAB Crates
For the Thomas Jefferson National Accelerator Facility (JLAB) in Virginia (USA), a special version of the VME 6023 crate series with front to rear air-cooling was developed. “JLAB style” VME crates are available with standard VME/VME64 backplane and mechanics as well as with VME64x or VXS (see VXS section) backplane and IEEE 1101.10 compatible mechanics, (enhanced EMC and ESD shielding).
-
product
LXI Function Card Carriers
ProDAQ 6100 Series
Ethernet-based LXI is changing the way engineers and scientists perform test and measurement and data acquisition. As more and more PCs ship without expansion slots, customers are faced with the problem of replacing their test and measurement and data acquisition equipment. Bustec believes in the power of distributed systems and the use of IEEE standards.
-
product
VME Power Supply
VME is a high speed and high performance bus system with powerful interrupt management and multiprocessor capability. It was created by combining VERSA-bus electrical specifications (1979) with the Euro card format resulting in the VME-bus Revision A - 1981 specification. The VME-bus specification has since then been refined through revisions B (1982), C, C.1, IEC 821 & IEC297 and IEEE 1014-1987. VME represents one of today's most used industry bus .
-
product
GPIB-RS232, GPIB-RS232, Instrument Control Device - North America 240VAC
779732-05
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
4U CompactPCI® Enclosure with cPCI Power Supply (non-CT Bus)
MIC-3042
The MIC-3042 is a 4U enclosure designed for standard cPCI power supplies. It is equipped with a cPCI 500 W redundant 2 1 power supply with hot-swap support. The system has 8 slots for CompactPCI boards and 6 slots for IEEE 1101.11 rear I/O transition boards. The MIC-3042 comes with a built-in high quality backplane that supports 64-bit / 66 MHz PCI cards.
-
product
Network Interface Card
PMC-GBIT-DT2BP
The Ethernet network interface complies with the IEEE 802.3 specifications for 10BaseT, 100BaseTX, and 1000BaseT over category 5 twisted-pair cable. Full-duplex and half duplex modes are supported. The PMC-GBIT-DT2BP is compliant with standard singlewide PMC IEEE P1386.1, PCI 2.2, and PCI-X 1.0 specifications.
-
product
Programmable Power Modules
Series MST
MST power modules are a group of programmable power supplies that are compatible with Kepco¹s single address, multiple instrument serial control bus. The MST provide precision interactive control in the 200 Watt power class. The housings for MST, either RA 55 or CA400, each contain a slot to accommodate an IEEE 488.2 adapter. If not used, an additional MST power module may be plugged into that slot.
-
product
Transformer Testing
The ART-3D series of Automatic Ratio Testers are precision instruments, designed to measure the turn ratios, phase displacements, excitation currents of single phase and three phase power, distribution and instrument transformers in conformity to the IEEE C57.12.90 & IEC 60076. Now featuring an enhanced test lead design, the ART-3D is the perfect instrument for real-life field usage. ART-3D series also has Anti Induction circuit which makes it suitable for system voltages upto 765KV.
-
product
TSEP Chronos 2.1
Technische Software Entwicklung Plazotta
TSEP Chronos is our implementation of the IEEE 1588-2019 standard. It’s made for a variety of platforms and it can be individually ported to various devices.
-
product
VPX/open VPX 5 Slot 3U
OpenVPX (ANSI/VITA 65 Standard) addresses this by specifying a set of standard profiles of interconnections. Comtel Backplanes are equipped with Air-/-Plane technology. It extends the life of the existing VPX connector system (MultiGig RT2) and enables unprecedented signal integrity performance which complies with IEEE 802.3bj 100Gb/s standard (4 Ethernet channels via fat pipe).
-
product
GPIB-RS232, Instrument Control Device - United States 120VAC
779732-01
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a … talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
BitPhyer Tools
BitPhyer is a family of hardware platforms used to test the IEEE 802.3™ MAC, Flow Control, PCS and RS layers for Ethernet devices, including Automotive Ethernet. This platform is based on Xilinx FPGAs and custom built hardware which are used to create a flexible bit-level based test system.
-
product
Type X2 double-shielded GPIB cable, 10 m
763061-10
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
product
CompactFlash Card
PMCF3
PMCF3 is a COTS IEEE 1386.1 compliant PMC with removable CompactFlash card up to 6 GB that offers a convenient way to add large capacity, non-volatile memory to rugged system solutions. Targeted at the world's defense and aerospace OEM marketplace, this cost-effective CompactFlash adapter is ideal for use with our families of COTS SBCs and PMC carrier cards.
-
product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - Swiss 220VAC
781630-02
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Avionics Network Simulation Systems
Avionics Interface Technologies
Support for up to 30 Network Interfaces (Fibre Channel & Ethernet)Time Synchronization with IRIG-B & IEEE 1588 Master ClocksFull Data Capture with time stampingData simulation with precise timing & synchronizationNetwork data replay from previously captured trafficPerform Network analysis using AIT's intuitive, easy to use, Ethernet & Fibre Channel simulation tools
-
product
GPIB
Advantech GPIB cards are compatible with the IEEE 488.2 standard. GPIB cards allow users to access and control instruments easily.
-
product
Serial-to-Daq Card
Model 2307
* 2307 Board provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Board. * DE-9 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * Runs on 5 Vdc power.
-
product
KPG 24kV VLF Test Set
Kilovolt Prueftechnik Chemnitz GmbH
The portable cable test set KPG 24kV VLF is used for testing of medium voltage cables in accordance to the standards IEC 60502-2, CENELEC HD 620 & 621, DIN VDE 0276/620 & 621 and IEEE 400.Test is carried out with a low strain practice with VLF (very low frequency) test voltage of preferably 0.1Hz.VLF testing enables detection of damages of insulation within shortest test time.
-
product
JTAG Boundary-Scan I/O Modules
SCANIO Family
The Corelis family of SCANIO™ modules turn any IEEE standard 1149.1 boundary-scan controller into a powerful digital boundary-scan tester. The SCANIO family of products use boundary-scan gate arrays to add control and visibility to connectors, traces, and logic that can not be tested using traditional boundary-scan techniques.The SCANIO products, when combined with a boundary-scan controller, operate as a traditional “bed-of-nails” tester except access to the stimulus and response I/O’s is achieved via boundary-scan.
-
product
GPIB Instrument Control Device
GPIB Instrument Control Devices offer IEEE 488 controllers that are compatible with ExpressCard, PMC, PCMCIA, PCIe, PCI, and USB slots as well as Ethernet, RS485, RS422, and RS232 ports. Some models can control multiple GPIB devices, and others offer sustained data transfer rates and no microprocessor interruption in data transfers. GPIB Instrument Control Devices include a license for the NI-488.2 driver software, providing maximum reliability for connecting to third-party instruments via GPIB. The devices are completely IEEE 488.2 compatible, have industry-standard transfer rates, and offer easy system configuration through NI software.
-
product
Sensor Database Implementing Imc Plug & Measure Technology
imc SENSORS
imc SENSORS is a ready-to-go, universal database application for administering and editing sensor information. Along with values for smart sensors defined in IEEE P 1451.4 (TEDS), selections of additional sensor properties can be freely entered. These can be set, edited and viewed in freely configurable tabular views, e.g., the sensor's technical data information, as well as its calibration values.
-
product
Premanaged Gigabit Ethernet Switch
XES-2T6
The XES-2T6 is a six plus two port Gigabit Ethernet switch with two ports being aggregated to a high throughput, redundant trunk link. The six other ports are individually assignable to groups (IEEE 802.1Q VLANs) that may participate in completely independent networks that do not interfere with each other. Thanks to the graphic OLED display, the encoder knob and a push button for each of the six configurable ports, the switch is intuitive to setup and the configuration is done in next to no time.
-
product
Transformer Turns Ratio Meters
Vanguard Instruments Company, Inc.
The ATRT-01 S3 is Vanguard’s fourth generation, micro-processor based, single phase, automatic transformer turns-ratio tester. The ATRT-01 S3 uses the IEEE C57.12.90 measuring method to determine the transformer turns-ratio. The transformer turns-ratio is determined by precisely measuring the voltages across the unloaded transformer windings. The ATRT-01 S3’s measuring circuitry self adjusts before each measurement to ensure turns-ratio accuracy. Two selectable test voltages, 4Vac and 40Vac, offer flexibility in testing different types of transformers.
-
product
Precision Time Protocol
IEEE-1588
Meinberg Funkuhren GmbH & Co. KG
As a high-stability Grandmaster Clock in IEEE 1588-2008 networks, the MEINBERG NTP time servers with highly accurate PTP clients ("slaves", such as the PTP270PEX or PTP SYNCBOX ) At the same time as the current absolute time.
-
product
2-port 10GbE PoE PCI Express Card
AX92324
Intel® Ethernet Controller X550-AT2, up to 10 Gbps data rate, Supports 15.5KB Jumbo Frame and IEEE 1588, Compliant with IEEE802.3at to deliver 25.5W per port, PCI Express x4 compliant, PoE power on/off via Power Manager software and API, Operating temperature range from 0°C to 55°C
