Fiber Optic Microscopes
Reveal quality of fiber end faces, splices and connectors.
-
product
4-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V
CPCI-7500
*This Model has a 37-pin D-Sub male connector*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)*Transmission mode asynchronous, full, half duplex*Transfer rate: progr. up to 115.2 kBaud up to 1 MBaud on request*Protocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bits*Parity: even, odd, none, mark or space*Interrupt lines: automatic through BIOS
-
product
Erbium Doped Fiber Amplifier
S-102
The EDFA slot module of FOTS system with built-in power booster EDFA module offers a special function that is able to change the optical signal amplification feature variously, which is followed by user’s driving embedded pump LD freely. The output power of eash pump LD can be controlled separately by the program that is set up by user. When an optimum optical signal amplification particularity is needed, it is made up so that it can be materialized by choosing the Default mode provided along with User mode. More stable application of EDFA is possible through the monitoring of the factors such as in/out signal power, gain, alarm status and pump LD enabled by the application of FPGA processor which makes high speed driving possible. It is also set up that user’s present-time monitoring and control through LCD monitor of system main frame or GUI display for remote control can be possible. Through optimization of amplifier gain, noise figure, and saturated output power, this EDFA module will expand test capabilities in systems, components or sub-assembly manufacturing.
-
product
Optical Test Instruments
OptiSpheric® & Spherometer
TRIOPTICS' OptiSpheric® and Spherometer are the classic optical test systems for spherical lenses that can be found in virtually any optical manufacturing process. While the Spherometer is used for the tactile determination of lens radii, OptiSpheric® systems provide contactless measurement of effective focal length, back focal length, flange focal length, MTF on axis and the radius of lenses. Specific upgrades allow determining centration errors and angles on plane surfaces. Systems for testing IOLs in compliance with EN/ISO 11979 form a class of their own. OptiSpheric® IOL R&D is preferably used for measuring single lenses while OptiSpheric® IOL PRO 2 is designed for the fully automated IOL measurement in serial production.
-
product
Light Microscopes
Compound light microscopes from Leica Microsystems meet the highest demands whatever the application – from routine laboratory work to the research of multi-dimensional dynamic processes in living cells.
-
-
product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800C (3RU)
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800C (3RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
product
LXI Dual 4:1 Optical MUX SC Multi-Mode
60-851-209
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
Current Loop 20 MA Constant Current SI-module With Optical Isolation
MXTTY
Current loop 20 mA constant current (active, passive) SI-module with optical isolation.
-
product
4 10/100M LAN FTTH EPON ONU ( Optical Network Unit )
ONU-4FE
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai ONU-4FE optical network unit (ONU), based Gigabit Ethernet Passive Optical Network FTTH EPON system user side equipment, combined EPON OLT (Optical Line Terminal) via a passive optical network PON, to achieve a multipoint (P2MP) high-speed data transmission. Provides powerful data, voice and video and other broadband services to users..
-
product
28/45 GHz Dual Optical Channel and 50 GHz Dual Electrical Channel DCA-M
N1092E
High accuracy, low cost solution for optical and electrical waveform analysis including solutions for 8.4 through 64 GBaud, very low noise and jitter, and fast sampling rates for high throughput.
-
product
1.5µm PM Ev-Yb Fiber Amplifier ( PM EYDFA )
HAPM5000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM5000 is a C-Band Polarization Maintaining Optical Amplifier which worked in 1540~1570nm operating wavelength. Adopt Polarization Maintaining (PM) Multiclad Ev-Yb fiber, output optical power range 27~37dBm(0.5W~5W) ， extinction ratio >20dB.
-
product
High-Speed/LED Sensing Fiber Sensor
FX2
Panasonic Industrial Devices Sales Company of America
The FX2 Series Fiber Sensor has multiple amplifiers. The FX-A3R has a 15us high speed response time and is suitable for detecting small objects or objects traveling at high speed. The FX2-A3R-LED is an LED sensing type amplifier, which can detect weak lighting from LEDs.
-
product
Mini OTDR Optical Time Domain Reflectometer
X30
Mini OTDR X-30 is a very reliable and good performance OTDR, it can measure the optical fiber length, transmission attenuation of optical fiber, attenuation of splice, and failure location, etc accurately. It is widely used in the maintenance, construction and monitoring of cable line. It is also very easy to carry because of its small size and light weight.
-
product
Atomic Force Microscope for SEM/FIB
AFSEM® AFM Insert
AFSEM is an atomic force microscope (AFM), designed for integration in a SEM or Dualbeam (SEM/FIB) microscope. Its open access design allows you to simultaneously operate SEM and AFM inside the SEM vacuum chamber. The correlated image data of AFM and SEM enable unique characterization of your sample, and the combination of complementary techniques is a key success factor for gaining new insights into the micro and nano worlds. AFSEM enables you to easily combine two of the most powerful analysis techniques to greatly extend your correlative microscopy and analysis possibilities.
-
product
Light Measurement Input Optics
International Light Technologies
Light measurement units are defined around very specific spatial responses. A carefully designed input optics system is essential if measurement accuracy is to be achieved.
-
product
950~2600MHz Satellite L-Band PIN Optical Receiver
HRS-26S/P
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HRS-26S/P optical receiver, adopting high-sensitivity PIN detector, receiving sensitivity is -22dBm, typical value: -13dBm. It can receive analogue and digital signal on satellite antenna LNB with the frequency of 950~2600MHz, It can be compatible with any FTTx PON to realize combination of Direct Broadcasting Satellite (DBS)with Internet and FTTH, it can also be used for L-Band uplink/downlink of satellite communication.
-
product
Optical Equipment
It is intended for the organization of multiservice, hybrid, optical-coaxial cable networks. Years of development and research in this area have allowed Planar LLC to create a product line that covers the widest range of applications. All equipment is an outstanding example of the high technology of Planar LLC, each of the models is the result of intensive research and lengthy tests. This synthesis of technical sophistication and daily labor practically means that all equipment is highly reliable and exceptionally cost effective.
-
product
Intraocular Lens Optical Test System
OptiSpheric® IOL R&D
The OptiSpheric® IOL R&D is specially designed for the analysis of single intraocular lenses in research and development. With the OptiSpheric® IOL R&D, important parameters of all types of lenses (monofocal, multifocal, trifocal, toric, aspheric and those with extended depth of focus (EDOF) – whether diffractive, refractive or sectors) can be measured and tested in air or in situ in accordance with ISO 11979.
-
product
RS422 Mode SI-module With Optical Isolation And RTS/CTS
MX422-PEP
RS422 mode SI-module with optical isolation and RTS/CTS
-
product
Ultra Miniature Rotating Optical Chopper
360C
A small compact low cost system suitable for OEM use. 10 Hz - 14,000 Hz standard chopping frequency range.
-
product
Fiber Optic Inspection & Cleaning
One of the most basic and important procedures for the maintenance of fiber optic systems is to clean the fiber optic equipment.
-
product
Stereo and Zoom Microscopes
Generate three-dimensional and laterally precise images. With Stereo Microscope you observe large samples such as leafs and tissues or inspect rough material surfaces. Upgrade your microscope flexibly with different digital cameras and benefit from various types of illumination techniques.
-
product
Fiber Inspection Probe
FIP-920
FIP-920 Fiber Optic Inspection Probe combines a 3.5” high definition TFT LCD display, provides a detailed image of fiber end-face, zoom in/out feature make it easy to identify the smallest particles, scratches. With the attached SD card memory, you can capture/record the live end-face image, the image file can be reviewed/transferred via SD card reader or USB cable. Up to 8hrs battery working make it possible to inspect the fiber end-face at any time and any place.
-
product
Variable Optical Attenuator - MATRIQ
The VOA MATRIQ Series is a MEMS-based variable optical attenuator with fast attenuation speed, low insertion loss and in-built power meter. Its advanced power stabilization function lets you set and maintain the output power stability even when the input power fluctuates.It is available in singlemode, multimode and polarization maintaining fibre types and various wavelengths to suit a wide range of applications.With a stackable, space-saving design and intuitive software controls make it a valued addition to the optical lab or test bench.
-
product
Erbium Doped Fiber Amplifier
EDFA
Optoplex designed and produced high power single-mode and polarization-maintaining EDFA, which met MSA compatible requirements. C-band MSA EDFA Module with +23 dBm Output Power is Optoplex standard product. Optoplex designed Pre-EDFA provides more than 35dB gain with -40dBm input power. The Double-Cladding pumped EDFA produces 2W output power.
-
product
Digital I/O Board, 64 Optically Isolated Digital I/O Channels,, 5V
APCI-1564-5V
*32 digital input channels, 5V, incl. 16 interruptible*32 digital output channels, 5V, 500 mA / channel*Optical isolation 1000V*Input and output filters*Watchdog, timer*After power/ON the outputs are reset to ì0î
-
product
Optical Apertures
The APPLIED IMAGE Optical Aperture reticles are available in sizes from 10μm (0.01mm) to 1,000μm (1.0mm) center openings (noted by -10, -25, -30 etc.), on either Chrome on Glass or Chrome on Opal material, with an overall size of 25.4mm (1.0 inch) diameter.
-
product
Square Head Fiber
Panasonic Industrial Devices Sales Company of America
Panasonic Square Head Type Fibers are compact and allow for right angle, space-saving installation, with minimum pitch using needle-nose pliers. These Fibers are also lens compatible for longer detection.
-
product
Fiber Lab Flex
The Fiber Lab Flex from M2 Optics is a unique platform designed to offer engineers with maximum versatility when requiring optical fiber spools for network simulation, latency, training, and other testing and networking applications.
-
product
Optical Controllers
Teilch’s compact DM controller for the Kilo DM is capable of delivering 16bit resolution over 220V and with dynamic range of 1kHz. System is directly integrated with the Zif Socket, eliminating the need for cables and providing a direct mechanical connection from the bench mount to the DM.
