Temperature Sensors
Convert temperature into a measurable electrical signal.
-
product
Fiber optic thermometer systems
TS Series
Micronor now offers a complete range of fiber optic temperature sensors, probes and interfaces for temperature measurement in challenging environments. TS series fiber optic temperature probes offer immunity to RF and microwave radiation along with wide temperature range, intrinsic safety and non-invasive use. The fiber optic temperature probes can operate over -200°C to +300°C (-328°F to +572°C), and withstand harsh and corrosive environments. Typical fiber optic temperature monitoring applications include:
-
product
Temperature & Environment Sensors
Environment Monitoring is an important function for facilities of all types including IT data centers, warehouses, schools, hospitals, offices, restaurants, farms, factories, zoos, museums and more. Maintaining a stable environment where equipment and/or products are housed is critical for their continued operation, protection and use. With this in mind, monitoring is typically needed on a continual basis. The 'IT & Facilities Environment Monitoring' market is arguably one of the fastest growing niches in the computer industry and yet surprisingly remains 'under the radar' of many IT and facilities managers... at least until disaster strikes.
-
product
Logger version conductivity and temperature sensor with wiper
INFINITY-CTW ACTW-USB
Infinity-CTW is an autonomously deployable data logger for highly accurate temperature and salinity measurements during long-term periods. The instrument has a mechanical wiper that periodically sweeps the sensing surface of the seven-electrode conductivity cell to keep the initial accuracy, avoiding bio-fouling without chemical materials and frequent maintenances. Infinity-CTW allows for accurate and stable salinity measurements for several months without cleaning maintenances. Infinity-CTW performance was evaluated and reported by Alliance for Coastal Technologies, ACT code: VS09-06).
-
product
Averaging Clip-on Extensometer
2650 Series
The Instron 2650 Series Biaxial Extensometers are ideally suited for testing a wide range of materials, including polymer matrix composites, metals, and plastics over a range of temperatures. Two sensors measure axial strain on opposite sides of the specimen. Versions are available which provide either a single averaged axial output or 2 independent axial outputs. The extensometers meet the calibration requirements of ASTM E83 class B1, ISO 9513 class 0.5, and ISO 527.
-
product
Inputs Temperature Data Logger – Pt100
HD32.7
The instrument HD32.7 is a robust 8 inputs data logger for Pt100 sensor temperature probes. The probes can be Pt100 with SICRAM module, direct 4-wire Pt100 or direct 2-wire Pt1000.
-
product
LilyPad Temperature Sensor
Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to digital conversion on the signal line will allow you to establish the local ambient temperature. Detect physical touch based on body heat and ambient conditions with this small sensor.
-
product
Soil Moisture & Temperature Sensor
Mini-Logger
The PlantCare Mini-Logger is a maintenance-free sensor which records soil moisture and soil temperature. A USB stick is used to easily program the mini-logger and readout the data. The PlantCare DataViewer Software allows a quick and easy display and analysis of the measured data. Fields of application are scientific research, agriculture and garden and landscaping construction.
-
product
DeepCover Embedded Security in IoT Authenticated Sensing and Notification
MAXREFDES143#
The MAXREFDES143# is an Internet of Things (IoT) embedded security reference design, built to protect an industrial sensing node by means of authentication and notification to a web server. The hardware includes a peripheral module representing a protected sensor node monitoring operating temperature and remaining life of a filter (simulated through ambient light sensing) and an mbed shield representing a controller node responsible for monitoring one or more sensor nodes. The design is hierarchical with each controller node communicating data from connected sensor nodes to a web server that maintains a centralized log and dispatches notifications as necessary. The mbed shield contains a Wi-Fi module, a DS2465 coprocessor with 1-Wire® master function, an LCD, LEDs, and pushbuttons. The protected sensor node contains a DS28E15 authenticator, a DS7505 temperature sensor, and a MAX44009 light sensor. The mbed shield communicates to a web server by the onboard Wi-Fi module and to the protected sensor node with I2C and 1-Wire. The MAXREFDES143# is equipped with a standard shield connector for immediate testing using an mbed board such as the MAX32600MBED#. The simplicity of this design enables rapid integration into any star-topology IoT network requiring the heightened security with low overhead provided by the SHA-256 symmetric-key algorithm.
-
product
NITlab Chassis Manager Card
NITLAB designed and implemented a Chassis Manager(CM) card to control and monitor NITOS nodes. CM card is comprised of a general-purpose microcontroller, an ethernet microcontroller and a relays circuit. General-purpose microcontroller supports a tiny web server and can serve http requests such as power on/off and reset. Furthermore, it returns the operation status of the node and can support a temperature & humidity sensor and a light sensor as well.
-
product
Dry Bulb Temperature Probe for WBGT
TP3207
Pt100 sensor temperature probe. Probe stem Ø 14 mm, length 140 mm. Cable length 2 metres. Equipped with SICRAM module.
-
-
product
Temperature Loop Control Setup
ULP-27
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Temperature Control Loop Setup is basically a PC based PID controller setup used for closed loop and open loop analysis of temperature process system. The setup comprises of RTD temperature Sensor. The water flows through the Rotameter and Process tank to which a heating coil is fitted. The heater is controlled by a Thirstier drive. The Thirstier drive is connected to PID controller. The manual control valve can control the water flow. The system is mounted on a tabletop model with all necessary Piping. Water at approx. 100 LPH has to be supplied to a system externally. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
-
product
Temperature and Humidity Regulator
H3060
Built-in humidity, temperature sensors. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Reference Cells For PIV-IV Systems
NREL calibrated cell used for calibration transfer.The Abet Technologies solar reference cell is a precision instrument for the determination of solar simulator irradiance levels. The sensor is a mono-crystalline silicon solar cell having an area of2x2cm(4cm).The back of the solar cell is attached to the device in such a way that a good heat transfer to the device housing is guaranteed. Below the solar cell a Pt100 RTD temperature sensor is mounted to allow monitoring of device temperature. The device is not shunted allowing the whole IV-curve to be measured. The solar cell is protected by a high quality fused silica window, assuring spectral sensitivity over a 320 -1100 nm range.
-
product
(2.5m) External Temperature Sensor
DT132
This MicroLog sensor takes external temperature measurements in a wider range than the internal temperature sensor. With a faster response time than the internal sensor, it enables measuring materials that cannot be measured with the internal sensor.
-
product
RH+T+Tdp Cable Probe
T3111-4
Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Integrating Sphere with Side Assistant Opening
IS-*MA**P/IS-*MA**C
According to IES LM-79 Clause 9.1.2, it request the 4π geometry configuration and 2π geometry Integrating Sphere for the LED Testing. Lisun Group developed the integrating sphere with side assistant Opening in A Molding Technology to meet the requirements.• Painting material of integrating spheres is according to CIE Pub.No.84 (1989) • The painting material is BaSO4 coating: ρ (λ) ≥0.96 (450nm~800nm) and ρ (λ) ≥0.92 (380nm~450nm) • Fine diffuse reflection: Reflectance ρ≈0.8 and accuracy of ρ (λ) <1.5% • Build-in all functional lamp testing jigs: the vertical is for E40/E27, the horizontal is for T5/T8/T12 tubes and the Testing Holder Base for LED street luminiares. All of the testing jigs can allow the lamp be tested up and down in the sphere. • Power Cable, Power Terminal and Auxiliary lamp position has been built-in (Auxiliary lamp is option). • Two photo detector ports, one optical fiber port and temperature sensor hole are built-in • Ordering Code: IS-1.5MA55P or IS-1.5MA55C (Φ1.5m, IS-1.5MA55P means square side opening is 0.5×0.5m, IS-1.5MA55C means cycle side opening diameter is 0.5m). IS-1.75MA66P or IS-1.75M66C (Φ1.75m and side opening is 0.6m). IS-2.0MA77P or IS-2.0MA77C (Φ2.0m and side opening is 0.7m). • Other size such as diameter 2.5m, 3.0m can be special order according to customer’s request
-
product
Wind Measurement and Meteorological System
Moriah
Aeronautical & General Instruments Ltd.
MWS is a solid-state system with no moving parts, so providing a highly accurate, reliable and low cost of ownership system, which is ideal for supporting ship based aviation activities. The system comprises of 1 to 5 Solid State Wind Sensors, Dual Redundant Processor Unit, a range of Multi-Function Color Displays (8.4”, 10.4” and 15.0”) and utility Software/Graphic User Interfaces. In addition full Meteorological capability can be achieved with the inclusion of Air Temperature & Humidity, Air Pressure and Sea Temperature Sensors.
-
product
Compressed Air RH+T+Tdp Sensor
T3111P
Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
CO₂ Humidity And Temperature Sensor
SCD40 (Qwiic)
The SCD40 from Sensirion is a high quality Photoacoustic based CO₂ sensor capable of detecting 0 to 40000ppm with the best accuracy over 400-2000ppm ±(40ppm+5%). In order to improve accuracy the SCD40 has integrated temperature and humidity sensing built-in. For additional accuracy the SCD40 also accepts ambient pressure readings!
-
product
Cryogenic Temperature Sensors
Platinum
PT-100 platinum resistance thermometers (PRTs) serve an important role in both cryogenic research and industrial cryogenics applications.
-
product
Humidity Sensors
ST’s digital humidity and temperature sensor is based on a planar capacitance technology that integrates the temperature and humidity sensors in the sensing element.
-
product
Profiler
fastCTD Profiler
An evolution of the miniCTD, it has a conductivity cell designed for optimum flow-through, a fast response thermistor temperature sensor and a 0.01% pressure sensor synchronously sampling at 32Hz deliver the highest quality profiles in a lightweight and robust package. The package is completed with an integral fluorometer based on Valeport’s new Hyperion range and optional Bluetooth communications module.
-
product
J-Type Thermocouples Wire, Fiberglass (32 deg F to 900 deg F) 1 m
745690-J001
J-Type Thermocouple, 32°F to 900°F Temperature Sensor - The J-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the J-Type Thermocouple and acquire synchronized temperature data in units of degrees. The J-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
THERMO MODULE OF THE COMPACT DEVICE FAMILY
ES620
This module measures temperatures using 16 electrically insulated measuring channels for temperature sensors. The adjustable acquisition rate per module is 10 samples/s to 0.1 samples/s. Signal smoothing occurs through a parameterized software filter, and high measuring accuracy is possible through 21 Bit resolution. The automotive measuring range is -210 C to 1372 C (-346 F to 2502 F); J, K, and N type thermocouples are used. Data transfer to PC occurs via Ethernet.
-
product
ATEX-Compliant IR Temperature Sensors
FLIR A310 ex
Explosive atmospheres need to be protected from ignition sources. Selecting equipment and protective systems which meet the requirements of the ATEX Product Regulations or similar regulations is essential. FLIR A310 ex is an ATEX compliant solution, with a thermal imaging camera mounted in an enclosure, making it possible to monitor critical and other valuable assets also in explosive atmospheres. Typical applications for the A310 ex include process monitoring, quality control, and fire detection in explosive locations. Because the FLIR A310 ex is rated IP 67, it can be installed in dusty environments. The Flame-Proof Enclosure "d"prevents any explosion transmission from the inside of the enclosure to the outside.
-
product
T-Type Thermocouple, 32°F to 500°F Temperature Sensor
745685-T01
T-Type Thermocouple, 32°F to 500°F Temperature Sensor - The T-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure … measurements and predefined scaling coefficients for the T-Type Thermocouple and acquire synchronized temperature data in units of degrees. The T-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
RTD Data Logger
RTD Data Logger is the most commonly used sensors for measuring temperatures in various industries. These are positive temperature coefficient resistive sensors and Pt100 is the most commonly used type of RTD sensor which has 100 ohm resistance at 0 C. IM2000 series RTD data loggers offer bridge measurement technique to compensate for effect of wire length. In addition logger has facility to program offset so that the measurements are more accurate.
-
product
Temperature
Accurate temperature measurement is the foundation of any building control system. ACI has temperature sensors to fit every application and meet the most demanding specifications. Most ACI temperature sensors are double encapsulated to ensure durability. ACI has the manufacturing flexibility to produce unique solutions for all volume needs.
-
product
Thermometer Calibrators
Check-Set Series
Tel-Tru® Manufacturing Company
The Check-Set series is the perfect temperature reference device for plant quality assurance, process control, food safety, instrument calibration and service, and HACCP compliance (Hazard Analysis Critical Control Points). It is easy to use, reliable, accurate, and compatible with a wide range of dial and digital thermometers, filled system bulbs, and electronic temperature sensors.
