Audio Cable Testers
-
Product
Audio Cable Testers
AudioJog Pro 5
-
ALL new Audio cable tester with SINGLE & DOUBLE ended testing. There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found.
-
Product
Audio Cable Tester
CBT-500
-
The CBT-500 Cable Tester by Hosa Technology diagnoses signal failure in cables terminated with any combination of XLR, Phone, Phono, and speakON® connectors, as well as DIN, Ethernet, 75-ohm BNC, and USB Type A to Type B cables. It is also equipped with removable leads to verify continuity of additional connectors and jacks. Operation requires one 9-volt battery (included).
-
Product
8 Plug Pro Audio Cable Tester
PCT10
-
Enables quick convenient continuity cable testing for all type of cablesLED's confirm each conductor continuity and connection6-Way Switch for selecting connections to be testedIncludes internal battery and ground connection status checkRugged, compact, metal construction for long life and reliabilityTests cables with all types combinations of the following connections3.5mm TRS Jack1/4' TRS Jacks3 Pin XLR Male3 Pin XLR FemaleRCA Phono4 Pin SpeakonBanana Plugs9V Batter (Not Included)
-
Product
12 Plug Pro Audio Cable Tester
PCT40
-
Enables quick convenient continuity cable testing for all type of cablesLED's confirm each conductor continuity and connection6-Way Switch for selecting connections to be testedIncludes internal battery and ground connection status checkRugged, compact, metal construction for long life and reliabilityTests cables with all types combinations of the following connections
-
Product
Audio Cable Testers
AudioJog Pro 3
-
Audio cable tester with SINGLE & DOUBLE ended testing, memory and intermittent fault detection .
-
Product
PAM4 Bit Error Rate Tester.
BERT-1102
-
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
Product
Bit Error Rate Tester - MATRIQ
-
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
-
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
-
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
Product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
-
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
Product
Automated Coherent Receiver Tester
CoRx Tester.
-
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
Product
PXIe Audio Analyzer
M9260A
-
M9260A is significantly different from the traditional general purpose PXI digitizer modules which are being used for today's audio measurement. In order to achieve fast test speed and high performance it comes with large one million sample arbitrary waveform buffer and one million sample "limitless" input buffer, as well as super-linear/low noise amplifiers and digital to analog converters. This enables M9260A's ultra-low residual distortion and high amplitude accuracy. M9260A is now an important part of Keysight Radio Test Solution, and may also be easily integrated into any audio related PXI test system with its developer-friendly drivers and commands.
-
Product
KVS Rugged Igniter Tester With Current Monitor
4314
-
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
Product
MTM-Bus Tester
PXIe-1149.5
-
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
Product
AXIe M8000 Series of BER Testers
-
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
Product
120 GBd High-performance BERT
M8050A
-
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
Product
Performance Audio Analyzer
U8903B
-
Measure your most demanding audio devices with higher accuracy and a low residual distortion of -110 dB See the real performance of your devices with the highest resolution audio measurements available Automate testing with built-in test sequences Meet standards more easily with pre-configured POLQA and PESQ measurements Simultaneously measure/view up to eight channels on a single screen in real time Configure for specific applications with digital audio interface (AES3/SPDIF and DSI) and Bluetooth audio measurements options
-
Product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
-
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Tinned Ends, 2m, Screwlocks
A068SFR-T-6B200
-
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
Cable Assembly, Receiver, Mini Coax, 36", 4 SMB Plugs
540104010207
-
Cable Assembly, Receiver, Mini Coax, 36", 4 SMB Plugs
-
Product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 1m, 250 Port
A500RMR-05F050D5C100
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to Unterminated (Tinned Ends), 2m
40-972B-200-2m-MU
-
This male rear exit to unterminated 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, unterminated with tinned ends. The connector assembly can be secured to the product by screwlocks.
-
Product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m
A015DM5-T-0A050
-
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 200 Pin Male LFH with M3 Jackscrews
540105020105
-
Cable Assembly, Receiver, TriPaddle, 20", 200-Pin Male LFH with M3 Jackscrews
-
Product
Cable Assy 78-Pin D-Type F/F 1m
40-970-078-1m-FF
-
A 78-Pin D-Type cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable to its associated products.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 36", 2 68-Pin Male Offset VHDCI
540205010229
-
Cable Assembly, Receiver, QuadraPaddle, 36", 2 68-Pin Male Offset VHDCI
-
Product
X13 GPIB Cable, MicroD25 to Shielded cable/Standard connector, 2M
183285-02
-
24-Pin Male/Female GPIB to 25-Pin Male Micro D-SUB GPIB Cable - The 24M-24F-MicroDB25M X13 GPIB Cable, sometimes referred to as the X13 cable, connects your system to GPIB devices or interfaces for instrument control. This standard shielded cable can connect PXI Controllers to instrument control devices and is offered in different lengths.
-
Product
Cable Assembly, Receiver, 36", Mini Power/TriPaddle, 9 Pin DIN, 4 Banana Plugs
540039030211
-
Cable Assembly, Receiver, 36", Mini Power/TriPaddle, 9 Pin DIN, 4 Banana Plugs.
-
Product
Cable, 25 Pin 1.27mm Pitch Micro-D, Female to Unterminated, Tinned Ends, 2m
A025CFR-T-5A200
-
This 2m long female 25-Pin Micro-D to unterminated (with tinned ends) cable assembly is constructed from 18/0.1 (26 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connector to its associated product.
-
Product
Cable Assembly, Receiver, 20/26GHz Coaxial, 36", 8 SMA Plugs
540259010253
-
Cable Assembly, Receiver, 20/26GHz Coaxial, 36", 8 SMA Plugs
