Three Phase Energy Meter
-
Product
Resistivity Meter of Powder Composites
RM-200
-
The resistivity meter is fully automated and does not required any adjustments. The measurement is made by using the four-point contact probe on the ring (ø60 x ø50 x 5mm) and rectangular prisms samples (6 x 6 x 60÷80mm). The measurement results are automatically saved in meter memory, what allows user to manage of data. The RM-200 contain series connection which allow the data transmission to PC.
-
-
Product
Blue ESR/Low Ohms Meter
-
This is the fully-assembled, cablibrated and tested Blue ESR/Low Ohms Meter The latest and best Bob Parker design and successor to the famous Dick Smith ESR/Low Ohms Meter. This handy and affordable meter measures capacitor equivalent series resistance (ESR) in the circuit. ESR is a very important characteristic of capacitors greater than 1 ufd. This meter makes measurements which are often impossible to check with capacitance meters.
-
Product
Wireless Energy Datalogger
ELITEpro XC™ Energy Logger
-
The ELITEpro XC is a complete solution for pinpointing electric usage and recording building performance metrics. It is capable of measuring, storing, and analyzing electrical consumption data which is derived from the voltage and current inputs. The ELITEpro XC uses direct connections to each phase of the voltage and various interchangeable CT options such as split-core current transformers, or flexible RoCoils (for large loads or large cables and bussbars) to monitor current on each phase.
-
Product
Lux Meters
-
Shenzhen Everbest Machinery Industry Co.,Ltd.
Unit of illuminance and luminous emittance, measuring luminous flux per unit area. It is equal to one lumen per square metre. In photometry, this is used as a measure of the intensity, as perceived by the human eye, of light that hits or passes through a surface.
-
Product
Three-phase Electricity Meters
-
Three-phase static electricity meters AMT B1x-S(D)xxTE are determined for single-rate or double-rate active energy measurement in direct and indirect connection, displaying results on mechanical register with stepping motor. In the case of CT (current transformer) operated meters (x/5A) it is necessary value of register to multiply by the current transformer ratio.
-
Product
Phase Monitors
-
NAI''s AC- and DC-powered Phase Monitors are used to protect three-phase loads from damage due to phase reversals or phase absence. Contacts may be used to disconnect the load or to operate alarm circuits or both. Upon application of power, the output relay energizes if all phases are connected and the phase sequence is ABC. If any phase becomes disconnected or if the phase rotation is abnormal, the relay immediately de-energizes. These monitors are specifically designed for rugged defense and industrial applications.
-
Product
Smart Water Meters
-
Smart prepaid water meter adopts a contactless IC card to store water volume and monitor water consumption. Customers purchase water volume at vending points and upload water volume by swiping his IC card on the induction area of installed water meter inside or outside home to activate valve, which will open automatically to supply water.During the period of water supply, the built-in microcomputer of water meter will automatically check and subtract the used water volume. Water meter has twice alarm function, when the purchased water volume reaches to alarm volume, water meter will close valve and stop water supply. Customer can resume water supply by swiping his IC card on water meter. When the remain water volume is used up, water meter will stop water supply completely and the customer needs to charge his IC card again.
-
Product
Analog Panel Meters
-
Analog panel meters offer accuracy and dependability and are available in Panel Board, Surface and Window mount styles. We offer variety of AC and DC input panel meters such as ammeters, voltmeters, frequency meters, elapsed time meters, etc.
-
Product
Industrial pH Meter
HP-480(W)
-
The industrial pH meter, HP-480(W) is a standard type pH meter equipped with frequently used functions suitable for on-site use. It supports a wide range of applications from manufacturing process monitoring, quality inspection, fisheries, aquaculture and many other industries.
-
Product
Electrostatic Meter
ESM-2
-
Our new development, ESM-2 electrostatic meter (successor of the tried and tested ESM-1) measures this alternating voltage via a hand-held probe against ground and displays its value digitally and thus easily readable. If the measured voltage exceeds certain values defined in the "Electrobiological standard", it can be reduced to noncritical values by means of targeted, usually simple, measurements.
-
Product
Flow Meter Sensor
RF Pickups
-
SPECTEC Innovative Sensor Solutions
SPECTEC RF pickups are excellent for applications that require near zero speed and zero magnetic drag sensing characteristics, such as flow meter sensor applications. SPECTEC RF (modulated carrier) sensors have a long history of use in turbine flow meters and turbine engines in the aerospace, petroleum, chemical, pharmaceutical and food industries.
-
Product
Sound Level Meters
-
A sound level meter is used for acoustic measurements. It is commonly a hand-held instrument with a microphone.
-
Product
Load Length Meter
-
Design for finding out the total voltage of neon tubes in a circuit, help to Choose correct rating of neon transformer;- Easy to use just like a neon transformer;- With color LED indicators, clearly shows the test result;- With build-in over voltage protection circuit.
-
Product
Multiparameter Water Quality Meter
ProDSS
-
YSI's ProDSS (Digital Sampling System) Multiparameter Handheld Meter provides flexibility and customization with a 4-port cable assembly outfitted with any four sensors, with or without depth.
-
Product
Portable Electricity Meter Testers
EE-120A-1S
-
The EE-120A-1S unit consists of a single-phase energy standard class 0.1 and current load up to 120A. The unit performs testing of all types single-phase electricity meters using the voltage of the site. The meter error can be measured for active, reactive or apparent energy, in Manual Mode or with predefined Test Plans using the keyboard and the LCD display on the panel. Register Test, Starting Current Test and No Load Test can be performed too. The energy standard of the system can be used without the phantom load to test meters with customer load and perform analysis of the site – with direct measurement or with optional current clamps.
-
Product
Resistance Meters
-
High-Speed High-Stable Resistance Meter with Low-impact Resistance Measurements for Miniature 008004-size Electronic Parts
-
Product
Optical Power Meter Heads
-
The 5mm detector area on Keysight's latest optical power heads allows flexible placement of the remote optical power meter, which is then connected to the N7749C. The wide choice of adapters allows input from popular fiber connector types, bare fibers or open beams. The magnetic D-shaped adapters allow rapid removal and replacement without twisting attached fibers.
-
Product
FC Impedance Meters
-
designed for testing of the fuel cell with the small current (5 A or less), and not only the current-voltage characteristic test, the KFM2005 can easily measure for the impedance of a fuel cell using the AC impedance method, and the Cole-Cole plot. Using the measurement data of the Cole-cole plot, it is possible to calculate the circuit constant of the approximate equivalent circuit of the fuel cell. The built-in DC load (60W) is capable to operate from 0 V, and it can perform the test for the fuel cell up to 20V and 5A.
-
Product
RF Milliwatt Meters
Type NDB-2 and NDB-3
-
National RF’s Type NDB-2 and NDB-3 RF Milliwatt Meters are affordable pieces of test equipment for both the RF laboratory and the home experimenter. Both provide a digital reading of RF power in dB reference 1 milliwatt of power into a 50 ohm load (i.e. 0 dBm). The circuitry consists of a low noise logarithmic amplifier that drives a digital A/D converting meter circuit. The lowest power levels that can be read are about –73 dBm (approximately 40 microvolts or .00000003 milliwatts). The maximum power input should not exceed 10 milliwatts (+10 dBm or .010 watts) when inputed without attenuation. An internal attenuator is provided and described in the next section.
-
Product
Laser Power Meter Monitor
11UNO
-
New 11UNO portable laser power meter brings unprecedented performance in a compact hand-held instrument. The one-finger navigation of the 11UNO laser power meter makes it our most simple to use monitor, and it has just the functions you need to take a fast and precise laser power measurement.
-
Product
Internally Ruggedized Phase Stable Test & Measurement Test Lead Assemblies
Storm-Test®
-
- Engineered to provide precise measurements with stable electrical performance- Excellent loss, VSWR, & phase/amplitude stability with flexure. - Internally ruggedized cable construction delivers longer life, repetitive mating and prevents crushing, bending & twisting- Accurate & repeatable measurements - Performance tested prior to shipment
-
Product
Phase Shifting Transformer
-
Supreme Instrument Laboratories
Supreme make PHASE SHIFTING TRANSFORMERS are special transformers which provide convenient means to adjust phase angle (power factor) of A.C. loading circuit while testing power factor sensitive device for the full 90 degree LAG through '0' degree to 90 degree LEAD. Based on their rating these Phase shifters are manufactured in two configuration.
-
Product
Smart Energy Solutions
-
To address the needs of the smart energy market, we offer a platform that incorporates application-specific solutions as well as standard microcontroller, microprocessor, security, memory, wireless and power-line connectivity devices. This smart energy portfolio offers you best-in-class feature sets and performance for designing equipment for the smart grid. The smart meter architecture requires different levels of integration depending on system architecture partitioning, project timelines and the level of flexibility needed to address the requirements of different geographies and utility companies. Our platform provides a unique multi-level architecture built around a multi-core solution as illustrated below. A variety of devices can be used as building blocks for your smart meter design. These include metrology sensing (analog-to-digital conversion); metrology digital signal processing; application, communication and security processing as well as connectivity to area networks in homes neighborhoods.
-
Product
Benchtop pH/ORP/Ion Meter
LAQUA ION2000
-
Water quality analysis is repeatedly performed in laboratories on a daily basis. Our compact and powerful benchtop model was developed to provide simplicity with excellent on-site usability.
-
Product
Precision Capacitance Meter
TH2638
-
Changzhou Tonghui Electronic Co., Ltd.
TH2638 series is a new precision capacitance meter with higher test frequency. With small size and portable appearance, it is convenient for use on the shelves. With basic accuracy of ±0.07%, loss accuracy of 0.0005, test frequency up to 1MHz, 4.3-inch LCD screen, selectable Chinese-English operation interface, TH2638 series is easy to operate and provide fast and reliable test for ceramic capacitor production. Also, it can test all kinds of capacitors from low value to high value. The results of testing one capacitor for several times are quite stable and accurate, even for lower value capacitors. The tester is compatible with SCPI command set, and configured with manipulator and scanner interface, the scanner interface can scan the open/short/ load error calibration in each channel, 256 channels at most. In low frequency, there is signal level compensation function. When the impedance is very small, the internal resistance in signal source and test cable will cause the voltage on terminal of DUT lower than the set range, then this function will adjust the level to the set range.
-
Product
Meter Engineering Board
MEB
-
Perform qualification, disconnect, communication, and advanced functional tests with TESCO’s new Meter Engineering Board. With basic metrology (0.1% accuracy) TESCO’s new MEB can also be used as a demand board or a time-run board, as part of meter certification, or to meet regulatory testing requirements. A new socket design provides automated operation to make loading easier. All new TESCO boards include our new electronically actuated sockets.
-
Product
Digital Grain Moisture Meter
LD-LGMM-A10
-
Digital Grain moisture MeterLD-LGMM-A10is an advanced digital moisture measuring device with automatic moisture measurement of wide variety agriculture grains. It has most advanced revising mode and user friendly material type selection mode. Automatic temperature adjustment and moisture correction when no material is measured are important feature of this device. It works on AA batteries and consists of automatic power shut down feature. It is ideally used for moisture measurement in agricultural grains like wheat, soybean, beans sediment, coffee beans, rice, etc.
-
Product
Illuminance Meters
-
Konica Minolta Sensing Americas, Inc
Illuminance meter products are single element detectors that measure photometric brightness falling upon a surface. It is measured in footcandles or in lux. The Konica Minolta illuminance meters measure the amount of light that strikes a surface. These instruments display illuminance in either lux or foot-candles and they are lightweight, compact and portable.
-
Product
AC/DC Clamp Meter
3900 CL
-
Standard Electric Works Co., Ltd
● 4000- count LCD.● Full automatic measurement. ◎ Voltage measurement. ◎ Current measurement. ◎ Resistor measurement. ◎ External frequency measurement.● Range change function.● Data Hold function freezes the reading.● REL function.● Peak function.● VAHz mode measures frequency in ACV and ACA mode.● Max/Min function.● Continuity check.● Low battery indication.● Auto Power Off (APO) function.● Safety design throughout with no exposed metal parts, shielded banana plugs and recessed input terminals.
