Ground Fault
-
product
Visual Fault Locator
FFL-210-U
FFL-210-U Visual Fault Locator is equipped with a 650 nm high power visible laser diode,can be operated in CW (continuous) or MOD (1Hz modulation) mode. There are two LED indicators：RED & GREEN; the RED one shows the operating mode of the Laser Diode output signal, and the GREEN one indicates low battery level. FFL-210-U is housed in a pocket-size, rugged metal casing, comes with a carrying pouch.
-
product
Neutrino Ground ISR
SX12 ISR1200
The Neutrino SX12 ISR1200 is the inaugural series model. With a 1280×1024/12 µm resolution focal plane array (FPA), a 120 mm to 1,200mm CZ lens, and advanced image processing, it is the ideal OEM camera module for integration into long-range ground ISR, perimeter surveillance, border surveillance, and counter-UAS (CUAS) systems.
-
product
Fiber Visual Fault Locator
Fiber visual fault locator is a pen type device which is able to locate the breakpoint, bending or cracking of the fiber glass,this small fiber optic equipment can locate the fault of OTDR dead zone and make fiber iIdentification from one end to the other end .
-
product
Pen Style Visual Fault Locator
CARY-VFLXX
The CAWI-VFLxx Economical VFL is an efficient and low cost basic fiber test tool, it provides a visible way to find fiber faults and identify fibers in an optical network duringand after installation.
-
product
Ground Leads Continuity Tester
Weshine Electric Manufacturing Co., Ltd
1. The new power supply technology is adopted in the grounding down lead conduction tester.2. It has the characteristics of small size, light weight, large output current, good repeatability, strong anti-interference ability and protection function. 3. The whole machine is controlled by single chip microcomputer, which has a high degree of automation. 4. The instrument has high precision and easy operation. The maximum current is 10A.
-
product
Ground Penetrating Radar
FINDAR®
FINDAR® enables law enforcement to quickly and effectively search for evidence buried under the ground
-
product
Cable Fault Location
BAUR Prüf- und Messtechnik GmbH
BAUR cable fault location devices and systems cover the entire cable fault location process: During pre-location, the position of the fault is roughly located. The subsequent pinpointing enables precise determination of the cable fault. You can use various measurement methods depending on the kind of fault and cable type.
-
product
Cable Fault Location System
Syscompact 2000 M Pro
BAUR Prüf- und Messtechnik GmbH
Cable fault location system 2000 M pro. The portable BAUR Syscompact 2000 M pro cable fault location system is used for cable fault location and cable testing in low- and medium-voltage cables up to 65 km length.* Fully integrated proven cable fault pre-location methods* Surge mode for acoustic pin-pointing* Easily transportable* Ideal for locations that are difficult to access
-
product
Ground Isolated ICP® Pressure Sensors For High Frequency
PCB® Series 102B is a ground isolated version of the Series 113B. These sensors have all of the same features and benefits of the 113B Series, plus the added benefit of isolation, which helps prevent ground loop problems. This series can accommodate an optional ablative coating (Prefix: CA) to protect the diaphragm from thermal shock in flash-temperature applications.
-
product
ESD Ground Point
EGP-020
The EGP-020 ESD Ground Point is a convenient mechanical socket that can be mounted on to any equipment frame for equal-potential bonding to the equipment. The 4 mm socket is not insulated, made of lathed brass, nickel-plated, for use as grounding socket.The EGP-020 is designed to be mounted on an unpainted conductive surface.
-
product
Portable Ground Strap Tester
This Ground Strap Tester provides an inexpensive method for guaranteeing the integrity of wrist straps. This compact, automatic test unit checks the specified resistance limits of all types of wrist straps and other similar personnel grounding devices. Incorporates upper and lower resistance tests.
-
product
Static Grounding Protection for Process Plant & Equipment
Earth-Rite PLUS
Precision and reliability is what the Earth-Rite PLUS provides to HAZMAT professionals and engineers who are tasked with protecting personnel and plant assets from the ignition hazards of static electricity during tank car, LACT & skid unit and tote loading/unloading operations.
-
product
Static Grounding for Process Plant & Equipment
Earth-Rite OMEGA II
The Earth-Rite OMEGA II monitors the resistance of the static grounding circuit for processes where a risk of static charge accumulation on the equipment could result in an incendive electrostatic spark within locations that have potentially flammable atmospheres present.
-
product
Ground Bond Tester,
266
Our 266 Model makes Ground Bond / High Continuity Testing simple with 60 Amps of current to satisfy your toughest NRTL standard. With an intuitive interface that allows you to set-up a test in seconds and practical security settings, our 266 can easily be deployed in both laboratory and production line environments. Ensure every Ground Bond Test is accurate with our Milliohm offset function.
-
-
product
Cable Sheath Testing and Fault Location System
Shirla
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR shirla. Shirla the fault location system is used for cable and cable sheath testing as well as for pre-location and pinpointing of cable faults. The pre-location based on the measuring bridge principle according to Murray and Glaser that is designed especially for power cables, also enables pre-location for control and lighting cables. Null balance and evaluation take place automatically.* Cable and cable sheath testing up to 10 kVC* Resistance measurement* Cable and cable sheath fault pre-location with precision measuring bridge* Adjustable cable sections that can be defined with length, conductor cross-section and material respectively and can be considered in the distance calculation
-
product
Visual Fault Locator ( VFL)
TM315N
The TM315N Economical VFL is an efficient and low cost basic fiber test tool, it provides a visible way to find fiber faults and identify fibers in an optical network during and after installation.
-
product
3U VPX 3 Slot Power & Ground, 2 x VITA 67
1900002601-9001R
The only assigned pins on these backplanes are for 3.3V, 5V and 12V power, and both ground and utility planes are defined. The remaining pins are all user-defined. The rear connectors are all fully populated.
-
product
3U VPX 3 Slot Power & Ground With 2x VITA 67.3D Apertures In J2 And J3
1900002601-0001R
The only assigned pins on these backplanes are for 3.3V, 5V and 12V power, and both ground and utility planes are defined. The remaining pins are all user-defined. The rear connectors are all fully populated.
-
product
Cable Fault Locator System
Kvtester Electronics Technology Co.,Ltd
To test the HV arcing fault of cable, earthing high &low resistance, short circuit and breakage of the cable, poor contact, etc. If equipped with fault locator, it can decide the exact broken position of the cable ,applies to power cable in various type, voltage and communication cable
-
product
Earth Ground Test Lead Kit
TL-796
*Earth Resistance Test Lead Kit*For use with IDEAL 61-796 3-Pole Ground Resistance Tester
-
product
Fault finder
The STaff™
The staff fault finder is designed to meet the demands of the professional troubleshooter but its simplicity and price make it a tool for anyone needing to locate cable faults. Arrows on the LCD screen direct the user to the fault with pinpoint accuracy. A reference indication also will aid the user in identifying multiple faults when present. Whether you are fault locating utility service line or locating a broken sprinkler wire, the STAFF is the professional's choice.
-
product
Fiber Optic Power Meters and Fault Locators
Fiber optic communication systems require the right tools to commission new links and to troubleshoot existing links. Fluke Networks has a wide range of Fiber Optic testing products to help certify that power losses are within standards and to troubleshoot broken and high loss links on single mode and multimode fiber. Fluke Network fiber optic tools are designed to be rugged and reliable, and to get the job done.
-
product
Cable Fault Locator
HT-TC / 400
Wuhan Huatian Electric Power Automation Co., Ltd.
Important test tools for wireline communication and power transmission line maintenance.
-
product
Visual Fault Locators
Visual fault locators are used to identify problems with your fiber. GAOTek visual fault locators typically are applied for fiber tracing, fiber routine, and continuity checking. Imagine being able to easily identify when and where a fiber is breaking, bending, or when there’s a threat to the fiber layer.
-
product
Detection of Earth Faults (PtG) and Short Circuit (PtP) Faults
CableTroll 2330
CableTroll 2330 is an indicator for detection of earth faults (PtG) and short circuit (PtP) faults on multi and single core cable terminations. The unit uses NorTroll type current sensors.
-
product
AC Ground Bond Tester
446
Our 446 model is a 4-in-1 tester with AC Hipot, DC Hipot, Insulation Resistance, and Ground Bond capabilities. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application. The 446 is equipped with multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Add to user safety by equipping your tester with Personal Protective Equipment (PPE) via the built-in safety interlock.
-
product
USB-8501, 1-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786306-01
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
product
Electrical Ground Support Equipment:
EGSE
Keysight provides a variety of configurable test systems for satellites and satellite flight hardware; including Solar Array Simulators, Battery Simulation and Conditioning, RF signal simulation and analysis as well as fully custom solutions.
-
product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
The 42-205-008 (PXIe) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
