Ground Resistance Clamps
See Also: Ground Resistance, Ground Resistance Testers
-
Product
Contact Resistance Meter
-
The Motwane Manufacturing Company
High contact resistance values are a definite cause of the failure or less than optimal performance in a wide variety of electrical devices. Contact resistance testing is therefore most critical to measure the resistance of electrical connections in switching devices, circuit breakers, isolators, busbars, relays, joints, connectors, cables, and cable joints. The device helps to find destructive or corroded contacts and hence protects substation devices from damage.
-
Product
Linear Polarization Resistance Probes
-
Linear polarization resistance (rosion probes are commonly used in the water treating industry and other environments where instantaneous, on-line corrosion rate readings are required. Linear polarization probes are ideally suited to monitor fluctuations that may occur within a system; for example, these probes can be used to monitor corrosion inhibitor effects on a regular basis.
-
Product
Ground Fault Locator
GFL-1000
-
The GFL-1000 ground fault locator is used to pinpoint faulty grounding where electrical cables have breakage and lost to the ground. The GFL-1000 is recommended by NERC PRC-005-2 to inspect for unintentional grounds for VLA, VRLA and NiCad batteries every four calendar months. Included software allows for data management analysis.
-
Product
C/I Clamp Meters
-
AC current measuring capability up to 400 amps. Compact size, fits easily into tool pouch. Data hold and Max hold to capture important readings. Lifetime Limited Warranty.
-
Product
Insulation Resistance Measurement
MI20KVe
-
The MI-20KVe High-Voltage insulation tester is a truly portable device that allows the measurement of insulation resistances using test voltages up to 20 kV.
-
Product
Insulation Resistance Tester
WB2681A
-
• Insulation test voltages: DC250V、DC500V、DC1000V • Range of open-circuit voltage: ±10% rated voltage • Testing time: 3~99 seconds or controlled manually
-
Product
AC Load Bank (Resistive)
K-1000 Resisitive
-
Kongter Test & Measurement Co., Limited
The kW of a resistive load bank is “real” power in electrical terms. When a resistive AC load bank is used to test an engine generator set the engine will produce its full horsepower rating, dissipate engine exhaust gases, and produce thermal energy into the engine cooling system. The resistive load bank in fact, will completely test the engine and its various systems.
-
-
Product
Resistivity Meter
Model 2180
-
The unit is compact and lightweight. The basic system is 7″ wide by 2.5″ high and 12″ long. When measurements are needed below approximately 100 micro-ohm-centimeters, the basic system is piggybacked onto a second enclosure that houses a power amplifier with a current gain of ten. The combined unit measures 7″ wide by 5″ high and 12″ long. The combined unit weighs 11.5 pounds. Two short cables interconnect the two enclosures for powering the power amplifier and routing the signals to the fixture or four point probe. The front panel of the basic system includes a 32-character backlit LCD display and a set of function keys. An easy-to-use menu will allow access to user defined parameters such as sample thickness, sample volume, and calibration constants; upper and lower alarm limits, relative measurements, and several others.
-
Product
Insulation Resistance Testers
-
Shanghai Beha Electronics Co., Ltd.
*This is a variable high voltage insulation tester from 500V to 15kV in 500V steps.*The is menu driven and uses Dynamic Current Auto ranging technology.*It has a Bar-Graph which displays the voltage stressing the insulation while the test is in progress and the voltage decay during the automatic discharge of the tested circuit.*The top line of the display shows the elapsed time at the start of the test. Digital readout of the total time will remain displayed even after testing has ceased.*A 4-digit display (2000 counts) is showing the actual insulation resistance.*This instrument displays a voltage warning and sounds when AC or DC is present before injecting the test voltage.
-
Product
Non-contact Io/Ior Leakage Clamp Meter
MCL-500IRV
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Safety by non-contact sensor, not touching live part directly (prevention of electric shock, short-circuit, etc.).・Easy to carry and operate, clamp CT + display part integrated type.・Measurable line current + leakage current + resistive leakage current by one unit.・Available direct voltage input at live part as ordinary.・True RMS measurement (I, Io, V).・With filter switch to cut high frequencies.
-
-
Product
Clamp Multimeters
-
Clamp meters test AC/DC voltage, DC voltage, resistance and continuity. Measure conductors at any point in the wire or cable.
-
Product
Non-Trip Earth Resistance Measurement
M73
-
M73 has been developed for operators who mainly work on private installations. M73 is very easy to use, it is very small in size and it carries out all necessary tests to establish COMPLIANCE (and hence ensure SAFETY) of an electric system.
-
Product
DC Resistance Tester
DCSS502BC
-
Resistance meter is designed to measure copper resistance of transformers, wires, cables, other conductors and other coil products etc. It is widely used of low resistance measurement of switches, heater wires, transformers, relays, motors, electric films and PC circuit boards, wires, cables, etc. With reliable Good/ NG judgement, it is a premier resistance meter for the use in production line or QC department.
-
Product
Digital Earth Resistance Testers
ST-1520
-
Capable of measuring earth voltage.2mA measuring current permits the testing of earth resistance without tripping earth leakage current circuit breakers in the circuit.Auto power off function.The timer operates automatically for approximately three to five minutes when the "push button switch" and "timer on button" are pressed together.
-
Product
Automated Temperature Resistance Standard
-
Measurements International Ltd.
Exceptional Stability, Cost-effectiveness, Performance-based Results, 10 Ω, 25 Ω, 100 Ω, 200 Ω, 400 Ω and 1000 Ω Internal Standards, Built-in Temperature Chamber for Optimal Performance.
-
Product
Contact Resistance Meter
CRM 200B
-
CRM 200B directly measures micro-ohm values at 100 Amps DC under live switchyard conditions.CRM 200B is specially designed to reliably measure contact resistance of circuit breakers, isolators, busbar joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards upto 765 kV.
-
-
Product
Concrete Surface Resistivity
Surf
-
Giatec Surf™ is a laboratory test device for rapid, easy and accurate measurement of the surface electrical resistivity of concrete based on the four-probe (Wenner-Array) technique. The Surf™ patented technology automatically measures resistivity around the concrete specimen using four channels of 4-probe array (located at 90° from each other). The PC software generates the required reports according to the standard specifications.
-
Product
Decade Resistance Boxes
-
A range of units to cover the requirements of development laboratories and calibration and test departments. High resistance instruments provide reliable calibration of insulation testers.
-
Product
Current Clamp Adapter
-
PeakTech Prüf- und Messtechnik GmbH
It uses a pair of jaw which allow clamping around an electrical conductor to measure the current in a conductor without the need to make physical contact unlike a normal multimeter.
-
Product
Resistance Substitution Box
RS Series
-
The RS Series Resistance Substitution Box is the most commonly used decade box on the market today. The RS Series is not only easier to use, but it is also priced lower than most its competition.
-
-
Product
Ground Fault Location
-
Kongter Test & Measurement Co., Limited
Kongter offers a whole line of ground fault locator from basic to advanced model to fast detect, trace and pinpoint virtual grounding faults in DC systems when systems are LIVE (working online). Without injecting any signal to the DC system, they are safe to your existing system. With Kongter’s unique technique for signal tracing, these ground fault locators are much faster and more effective to find the earth fault in the field than its peers.
-
Product
Digital Arrester Clamp Tester
ALCL-40L
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Lightning arresters are designed to protect a power distribution system by shunting to ground the high voltage surges caused by lightning. ALCL-40L measures to warn that an arrester is damaged or deteriorated and should not be energized.
-
Product
DC Resistance Tester
2511
-
Shenzhen Chuangxin Instruments Co., Ltd.
DC resistance tester. Resistance test range: LW-2511: (10µΩ—2K five shift). Test speed:6 times/fast. Test accuracy:0.2%±2digits。
-
Product
3.5 Digit Handheld Clamp Meters
U1210 Series
-
Measurements of electrical distribution cables can be challenging and risky. For cables up to 2 inches in diameter, the Keysight U1210 Series (U1211A, U1212A, U1213A) handheld amp clamp meters (also known as clamp-on ammeters) enable high-current measurements without breaking the circuit. Plus, they provide an extra layer of protection with CAT IV 600 V and CAT III 1000 V safety ratings and include full digital multimeter (DMM) measurement features.
-
Product
Handheld Grounding Tester
HGT1
-
The HGT1 is a handheld meter to measure ground impedance as well as step and touch voltages. Using the CPC 100 and CP CU1, test currents at variable frequencies can be fed into power cables or overhead lines safely to simulate a ground fault.
-
Product
DC Ground Fault Finder
FST-JD200
-
Foresight Electronics Co., Ltd.
FST-JD200 not only can provide a solution on accurately testing the faults of the indirect-grounding of the direct current system, non-metal grounding, loop grounding, simultaneous grounding of the anode and cathode, balanced grounding of the anode and cathode and multi-point grounding 1.
