Function Generators
produce repeating sawtooth, sine, square, or triangle waveforms.
-
product
Pattern Generators
PG311P Series
The MicroImage PG311 series of pattern generators are for applications to display custom designed patterns on screen. The PG311 units will overlay the pattern or patterns on top of the video signal provided to the input of the device. The PG311 can be factory programmed with one unique pattern.
-
product
Signal Generator
8005
5 digit BCD, 1 latch control line, 25 pin female, D type connector. Normal switching mode, SSB phase noise will be degraded in the fast mode.
-
product
2-Channel 400MHz DDS Signal Generator
2940A
The 2940A is a two-channel 400MHz DDS Signal Generator that generates two independent sine wave output frequencies simultaneously from 200kHz to 400MHz in 1Hz steps. A Clock Generator configuration with ECL or LVDS clock outputs is also available. The 2940A is lockable to an external frequency standard or is used with its internal TCXO. Optional internal amplifiers and 60dB step attentators available. Set all parameters with front panel controls and LCD display or by computer using the RS232 serial interface. All settings can be saved into non-volatile EEPROM memory upon power down. Windows software included.
-
product
Envision Analyzer & Generator
MIPI C-PHY/D-PHY
The Envision X14 Analyzer capture utility provides deep analysis for MIPI camera and display protocols over C-PHY and D-PHY layers. The X14 Analyzer can be positioned either as an endpoint to test a CSI-2 or DSI-2 stream or tapped in between a CSI-2 or DSI-2 device and host for passive monitoring and analysis. The Envision X14 ensures fast Time-to-Insight through its rich set of innovative features for debug analysis and identifying and resolving elusive protocol errors.
-
product
32-Channel Digital PMC with 30-ns Time Stamp function
2195
The Technobox 32-Channel Digital I/O board provides 32-bits of bi-directional CMOS-level (TTL compatible) I/O available at the JN4 connector on a PCI Mezzanine Card. The 32-bits are individually programmed for direction ? either input or output ? by a 32-bit register written by the host processor. A 56-ohm series terminator is provided for each line.
-
product
Clock Generator
CG-2000
Supports power supply and video / audio clock redundancy. The top model in the CG series equipped with various functions required for broadcasting stations and post-professional sites.
-
product
Multi-Function Digital Pattern Generator & Logic Analyzer
GP-241xx Series
Multi-function PC digital interface for digital IC and embedded system testing and debugging.
-
product
HD 8 Line Crosshair / Line Generator
CL8800
The CL8800 has four X and four Y moveable lines. The lines can be set to black or white and each line can be turned off or on individually. Lines may be changed from solid to serrated with one of many lines styles. A lock switch is provided for each of the four controls to prevent accidental movement.
-
product
General Purpose Surface Temperature Assembly
S2-2
The Series S2-2 General Purpose Surface Temperature Assembly is ideal for monitoring the temperature of indoor distribution lines when it is not possible to penetrate the pipe. The plastic housing is in the shape of a standard junction box with multiple knockouts for easy conduit access. The strap-on connection quickly wraps around a pipe and can be securely tightened using a flat head screw driver. The Series S2-2 can be ordered with a choice of 11 output options that allow it to communicate to any standard building control system
-
product
Vector Signal Generator
VSG25A
The VSG25A is a 100 MHz to 2.5 GHz vector signal generator, featuring a 12-bit I/Q baseband arbitrary waveform generator which can be clocked at virtually any frequency from 54 kHz to 180 MHz, and includes a 4096×16 bit pattern buffer for built-in or custom modulation.
-
product
D-Coupon Generator
Conductor Analysis Technologies, Inc
This coupon generator is based on the D-Coupon of IPC 2221B Appendix A. It is advised that you familiarize yourself with the coupon specifications before using the generator. It is also recommended that the drill, etch and soldermask fabrication compensations be applied uniformly to both the coupons and product board after the coupons have been designed.
-
-
product
PXI Bluetooth Signal Generation and Analysis
Test Toolkit for Bluetooth™
Start taking faster Bluetooth measurements with PXI, the most cost-effective, flexible, and capable platform for wireless device test. Keep up with the latest Bluetooth standard developments with free upgrades of the Test Toolkit for Bluetooth. Gain greater confidence in your Bluetooth design's performance and increase test coverage with a flexible toolkit that offers fine control of the generated Bluetooth waveforms and generates accurate measurement results.
-
product
Alternate 0.50 (14.00) - 2.50 (71.00) General Purpose Probe
P2662BG-1Q2S
Current Rating (Amps): 3Average DC Resistance lower than (mOhm): 30Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 68Full Travel (mm): 1.73Recommended Travel (mil): 50Recommended Travel (mm): 1.27Overall Length (mil): 575Overall Length (mm): 14.60
-
product
Standard 1.50 (42.00) - 3.30 (94.00) General Purpose Probe
P2663G-1P1S
Current Rating (Amps): 3Average DC Resistance lower than (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 90Full Travel (mm): 2.29Recommended Travel (mil): 67Recommended Travel (mm): 1.70Overall Length (mil): 810Overall Length (mm): 20.57
-
product
Impulse Generator
CTS-10350
The CTS-10350 is an impulse generator with a current wave shape 10/350 μs at the output terminals. Dual outputs enable testing of 2 terminal devices and 3 terminal devices up to class 1. The generator impedance is 1ohm in dual output mode or 0.5ohm when both outputs are connected together.
-
product
20 MHZ Arbitrary Waveform Generator
F175 AWG
he F175 AWG does not replace our current square wave generator models (F125/165/170/110). It is an arbitrary waveform generator. Its main strength is in producing non-square waves. Of course it is also able to produce square waves but if you only need generate square waves, please look at our other models: F125/165/170/110. We expect to have F175 AWG production boards available in the third quarter of 2009.
-
product
Standard 1.00 (28.00) - 2.75 (78.00) Non Replaceable General Purpose Probe
E-S-F
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 30Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 65Full Travel (mm): 1.65Recommended Travel (mil): 43Recommended Travel (mm): 1.09Overall Length (mil): 495Overall Length (mm): 12.57Rec. Mounting Hole Size (mil): 67Rec. Mounting Hole Size (mm): 1.70Recommended Drill Size: #51Overall Length Remark: Overall length for E-S-V and E-S-W is .540 (13.72)
-
product
2450 MHz Industrial Microwave Generators
Alter® 2450 MHz Industrial Microwave Generators are built on MKS Alter® Product experience and designed with rugged and reliable switch mode power supplies for demanding industrial applications. They offer compact generators up to 3kW in a 19 inch standard rack with a remote head and integrated isolator.
-
-
product
Quad sync generator
TELETEST SYNC
A very compact, high quality professional composite video sync generator with four outputs.
-
product
Non Replaceable General Purpose Probe
MEP-20
Current Rating (Amps): 2Average Probe Resistance (mOhm): 50Test Center (mil): 25Test Center (mm): 0.635Full Travel (mil): 75Full Travel (mm): 1.91Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 750Overall Length (mm): 19.05Rec. Mounting Hole Size (mil): 20.5Rec. Mounting Hole Size (mm): 0.52Rec. Mounting Hole Remark: 20.5 to 21.5 mil / 0.52 to 0.55 mmRecommended Drill Size: #75 or 0.52 mm
-
product
Carrier to Noise Generators
CNG-DX
Hollis Electronics Company LLC
CNG-DX provides improved noise generation with its internal digital power meter and built-in noise generator. This single instrument provides accurate and repetitive carrier-to-noise setting ability in one box. The CNG-DX is an ideal instrument for creating realistic scenarios for closed loop testing of satellites, ground equipment and mobile transceivers.
-
product
Tone Generator
Control and test 2-way radio systems, repeaters, ANI, Paging and more. Activate 2-tone or 5/6-tone pagers. Operate or test EIA tone-remote systems. Record generated signals to a WAV file Accomplish MORE, by carrying LESS hardware in the field. Monitor inputs and outputs with our FREE built-in audio scope and spectrum analyzer. No external hardware required. Output may be fed directly into radio, twisted pair, or service monitor.*
-
product
Signal Generator
8001
4 digit BCD, 1 latch control line, 25 pin female, D type connector. Range: 2 to 8 GHz (1.7 - 9.0 GHz, typical). 3 normal switching mode, SSB phase noise will be degraded in the fast switching mode
-
product
Shaft Speed Pulse Generators and Shaft Speed Targets
Shaft Speed Targets are needed to generate a pulse for a Speed Sensor that is monitoring a shaft for RPM (Revolution Per Minute). Electro-Sensors Pulse Generators provide the shaft speed target needed for shaft speed detection with a sensor or switch. We have many options available for all your application needs including customizable split collar pulser wraps.
-
product
Noise Generators
GShM Series
*Operating temperature: +15...+25°C*Detection error for excessive relative noise temperature: +/-0.4 dB*Power consumption — <35 mA
-
product
Ozone Generators & Systems
MKS offers a wide range of ozone generators and modular delivery systems which produce ultra-pure, reliable ozone gas. In the clean semiconductor environment, Ozone reacts with a wide range of precursor gases resulting in the creation of Al2O3, ZrO2, HfO2, and La2O3 metal oxides to enable thin film deposition processes like Atomic Layer Deposition (ALD) and Etch (ALE). MKS’ generator uses Grade 6 gas, enabling the creation of higher film density improving product yield. Photovoltaic and Display manufacturing leverage semiconductor best practices and utilize ozone to create enhanced thin film barriers, improving product performance and reliability.
-
product
PXI Low-Density General Purpose Switch Modules
These PXI low-density general purpose switch modules provide cost-effective solutions for applications where a high number of relays is not required. All of these modules use a 96 pin male connector that is supported by our comprehensive range of cable and connector accessories, ensuring they can be quickly integrated into your test system with minimum effort.
-
product
PXIe-5650, 1.3 GHz RF Signal Generator
781215-01
The PXIe‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
