Current Detectors
-
product
12 Channels 1.0 ~ 17.0 Gb/s (200Gbps) Pulse Pattern Generator and Error Detector
CA9806-12
The UC INSTRUEMNTS CA9806-12 is a highp erformance, flexible 12 channels Pulse Pattern Generator and Error Detector that can operate from 1.0 to 17.0 Gb/s (200 G). It is combined with three sets CA9806 4 CH 1.0 to 17.0 Gbps Pulse Pattern Generator and Error Detector that incorporates an external one by 4 rate clock synthesizer. Its small size allows it to be placed close to the device under test, it can also be placed further away using the TX driver pre and post emphasis controls features to compensate for cable and interconnect losses. It also has a non destructive, integrated eye outline capture feature along with a quick eye height and width measurement capability. Build-in 8.5 ~ 15 Gb/s eye diagram testing function.
-
product
Silicon Drift Detector
Octane Elite (SDD) Series
The game changing advancements in the Octane Elite Silicon Drift Detector (SDD) Series take detector technology to the next level. This line of detectors incorporates a new silicon nitride (Si3N4) window, which offers remarkable improvements in low energy sensitivity for light element detection and low kV microanalysis. The Octane Elite Series also uses the widely praised CUBE technology, which yields high speed X-ray data processing within a smaller and fully vacuum encapsulated detector device.
-
product
Current Logger0 to 25mA DC
TV-4804
The TV-4804 measures current from 0 to 25mA DC and can be connected to a variety of industry standard sensors enabling the logging of a wide range of process parameters.
-
product
Current Clamp Multimeters
PeakTech Prüf- und Messtechnik GmbH
It uses a pair of jaw which allow clamping around an electrical conductor to measure the current in a conductor without the need to make physical contact unlike a normal multimeter.
-
product
Primary & Secondary Current Injection Testing Sets
Primary current injection kits are used to test and commission Circuit Breakers, Bus Bars, CTs, Relays, MCCs, PCCs etc. These are also used for high current injection and simultaneously measuring voltage drops and hot spots in bus-bar joints, Circuit Breaker Contacts etc.
-
product
Point IR Gas Detector
IR400
The IR400 Infrared (IR) Point Detector is a hydrocarbon gas detector that continuously monitors combustible gases and vapors within the lower explosive limit (LEL) and provides alarm indication.
-
product
Portable Current Supply 10 AMP output
CS-10
The CS-10, Sure beats carrying around a rectifier and generator...
-
product
Current Sensors
Our current sensors were designed for a simple, customer-specific construction of niobium wire wound magnetometers, gradiometers or preamplifiers for small current or voltage signals.
-
-
product
Detector of Earth Faults on Multi/Single-Core Terminations
CableTroll 2310
CableTroll 2310 is an indicator for detection of earth faults (PtG) on multi-core and single core cable terminations. The unit uses NorTroll type current sensor (CT)
-
product
Volumetric Flow Detectors
FP-5000 Series
In engine evaluations such as emission mode tests and transient tests for performance evaluation, the evaluation methods have been shifting from steady-state tests to transient tests. In the evaluation of fuel consumption, the requirement for evaluating the fuel consumption characteristics in transient duration has been increasing as well as the total fuel consumption for each mode. The FP-5000 series has achieved high pulse resolution and wide measurement range. It enables to detect changes in the flow rate effectively and responsively, and measure large flow rate. It can be used when the flow rate increases, such as when measuring alcohol fuel.
-
product
Waveguide Power Detector
RF Lambda’s waveguide power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
-
product
Current Transducer
IN 1000-S
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. 1000 A nominal, 3 ppm linearity over the temp. range, Very low offset drift 19.5 ppm, low noise 34 ppm peak-peak, -40 to +85°C, one compact package.
-
product
High Current SMU 1000 A
AXC7583
Generate extremely short, fully regulated current pulses from 300 µs up to 1000 A. At the same time, carry out measurements directly on the DUT with the integrated VMU and CMU. Perfect for rapid semiconductor tests during production.ven Bauteilen.
-
product
Gas Detector — Methane, Butane, Propane
ENVIROMUX-GD-MBP
Use to detect leaks of combustible gas (methane, propane, butane, acetylene, etc.). Choose between two levels of detection. First level: Detects methane at concentrations in excess of 0.5%; Detects propane/iso-butane at concentrations in excess of 0.3%. Second level: Detects methane at concentrations in excess of 0.8%; Detects propane/iso-butane at concentrations in excess of 0.5%. Continuous air monitoring. Audible alarm signal: 94 dB at 1 foot. Relay specifications: level selectable, normally open or normally closed, 250V AC, max 5A. Maximum cable length: 1000 ft (305m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: CE.
-
product
ChromaPoint Detectors
E50
Sciences et Techniques Industrielles de la Lumière
E50 series is part of the STIL ChromaPoint detectors.All the optical fibers are passive components, graduated index silica fibers with a 50µm core, an E2000/APC connector for the connection with STIL controller and an FC/APC connector for the connection with STIL optical sensor head.
-
product
PXI/PXIe Wide Current Range Multiplexer Module, Single 12-Channel, 2-Pole
40-514-105
The 40-514-105 (PXI) and 42-514-105 (PXIe) are low density multiplexers in single 12-channel, 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
product
EVISION Obstacle Detector
MS 1528
Obstacle Detector is a distance-measuring system based on ultrasonic sound utilizing the LPC2364FBD100. The system transmits a burst of ultrasonic sound waves towards the subject and then receives the corresponding echo. The LPC2364FBD100 integrated analog comparator is used to detect the arrival of the echo to the system. The time taken for the ultrasonic burst to travel the distance from the system to the subject and back to the system is accurately measured by the LPC2364FBD100. Assuming the speed of sound in air at room temperature to be 1100 ft/s, the LPC2364FBD100 computes the distance between the system and the subject and gives the information to buzzer. The minimum distance that this system can measure is eight inches and is limited by the transmitter’s transducer settling-time. The maximum distance that can be measured is 2 meter. The amplitude of the echo depends on the reflecting material, shape, and size. Sound-absorbing targets such as carpets and reflecting surfaces less than two square feet in area reflect poorly. The maximum measurable range is lower for such subjects. If the amplitude of the echo received by the system is so low that it is not detectable by the Comparator. This system is mainly used to replace normal sticks for the visually impaired (blind) peoples. This unit has standard USB 2.0 for mobile interface and has android application for user interface
-
product
VME Master - DAQ and Detector Interface
VX1394
The VX1394 board features a radiation hard 4.8 Gbps SERDES ASIC, which, in connection to a rad-hard optical transceiver implements a newer generation optical links for many detector readout systems. The ASIC performs data transmission, trigger distribution and clock forwarding towards the front-end electronics in the crate.
-
product
EBSD Detector
e–FlashFS
The new EBSD detector e–FlashFS has been designed for maximum sensitivity to allow highspeed EBSD measurements without compromising data quality – even on challenging applications like deformed or lightweight materials. To further improve the pattern quality, the cooling system of the e–FlashFS has been upgraded to lower its functioning temperature and therefore reduce the dark current of the CCD camera as much as possible.
-
product
ElectroMagnetic Detector
MP Series
MP-900/9000 are chiefly used in conjunction with a detector gear mounted onto a rotating shaft by bringing the detector into proximity to the gear so that the detector outputs frequency signal of which is proportional to the rotational speed. So various types are available including low-priced, general purpose, oil proof and heat resistant types that you can make a choice for your usage.Signal cables (except attached-cable types), extension cables and connectors are sold separately.
-
product
Impulse Current Test Systems
Fivestar HV Testing Equipment Co., Ltd.
Impulse current test systems are mainly used for testing transmission and distribution systems against the effects of direct or indirect lightning strokes or against electromagnetic interference effects. Primary application of impulse current test systems is the testing of surge arresters, nowadays mainly of the metal-oxide type (MOA) and surge protection devices (SPD). Now they are also widely used to test vehicles, aircrafts, and military applications.
-
product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
41-752A-913
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
PXI/PXIe Wide Current Range Multiplexer Module, Single 24-Channel, 1-Pole
40-514-108
The 40-514-107 (PXI) and 42-514-107 (PXIe) are low density multiplexers in dual 12-channel, 1-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
product
PXI/PXIe Wide Current Range Multiplexer Module, Dual 12-Channel, 1-Pole
40-514-107
The 40-514-107 (PXI) and 42-514-107 (PXIe) are low density multiplexers in dual 12-channel, 1-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
product
High Frequency Current Transformer Clamps
HFCT-20HD & HFCT-60HD™
The HFCT-20HD™ and HFCT-60HD™ are high frequency current transformer sensors designed for partial discharge detection on electric apparatus’ ground returns. Made from superior quality materials, it is designed for any environment.
-
product
Direct Current Measurement Card
LQI5
Computer Gesteuerte Systeme GmbH
The LQI5 is a precision direct current measurement card. It features 6 measurement ranges for unipolar current measurements of up to 32 A. Current pulses shorter than 5 seconds can be measured up to 65 A.
-
product
Portable Pinhole Detector
DZK-18
Shanghai Dean Electrical Co., Ltd
Online testing mode: round wireΦ0.05 -Φ5.0, flat wire B side Φ 3 - Φ 18Hand detection mode: round line diameter is not required, flat line width is not requiredTest length: 0-999 m to infinity (set by user)Detection speed: set by the userDefect short circuit current: 25±5uAResponse time: 5 ±1msWorking environment:0-40℃Relative humidity: 75% or lessOperating voltage: AC220V±5%Power consumption: <20W
-
product
Flexible Rope-Type Current Probe
RCT1A and RCT5A
These probes have great bandwidth ensuring accurate measurement even with harmonically distorted wave shapes. For all RCT1A/RCT models, a NIST, NAVLAP, NPL (UKAS) factory traceable calibration certificate and certificate of conformance is supplied. UL/CSA approved materials are used throughout. Three phase and single phase flexible AC current sensors (rope sensors) are available for fast installation in confined spaces, eliminating the need for Electrical Supply Shutdown. Available outputs are 1A @ 2.5VA and 5A @ 0.5VA, this means long cable lengths from current sensor to signal conditioner allow these low VA ratings to be used, even when feeder cable to energy meter distances are large (up to 98 feet / 30 meters)
-
product
EBSD Detector
Symmetry
Electron backscatter diffraction – is a powerful microanalysis technique that enables rigorous characterisation of the micro structural properties of crystalline materials. A high performance EBSD detector is critical for the effectiveness of the technique, influencing both speed and data quality. Symetry is Over 3000 indexed patterns per second (pps). Up to 30x faster than existing CCD-based detectors. Extreme sensitivity for low current and low kV analyses. Megapixel resolution for HR-EBSD applications. High resolution patterns (at least 156 x 128 pixels) at all speeds.
