ATX Power Supply Testers
checks Advanced Technology eXtended power supplies.
See Also: Power Supply Testers
-
Product
Advanced Power System - Dynamic DC Power Supply, 40 V, 50 A, 2000 W
N7972A
DC Power Supply
The N7900 Series dynamic DC power supplies are designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
Product
VDI Erickson PM5B MM–Wave Power Meter with W-Band Sensor, Optional Tapers to 1.5 THz
N1913PM5B
Power Meter
N1913PM5B is a Virginia Diodes, Inc./Erickson PM5B calorimetric mm-wave power meter, with a W-Band sensor for power measurement over a frequency range of 75-110 GHz.
-
Product
Serial AC Power Sequencer
90-200-001
AC Power Sequencer
Each power outlet can be programmed to switched on in sequence with a specific timing delay. The delay can be staggered to ensure that order dependent systems - like PXI - can be switched on and off in an orderly way with just one operation. A staggered start up also limits the inrush current associated with the powering up of equipment, including earth current inrush, placing less stress on cabling and leakage breakers. Power on or off instructions can be initiated from either the front panel switch or via the serial interface.
-
Product
Custom Configured MPS, 600W
N6711C
Power Supply
The Keysight N6711C is a 600 W build-to-order system that is shipped as a fully tested and assembled multiple-output power supply. Each N6711C consists of 1 N6701C mainframe and from 1 to 4 DC power modules. Modules are ordered as options to the N6711C.
-
Product
10 MHz To 54 GHz USB Wide Dynamic Range Average Power Sensor
U2056XA
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis
-
Product
DC Power Supply, 30V, 5A
U8002A
DC Power Supply
The Keysight U8002A 30V/5A single-output, non-programmable DC power supplies is suitable for a variety of electronics manufacturing applications. With our affordable pricing, it is also well suited for usage in education labs.
-
Product
Power, Patchcord, Receiver, 72", Micro Power, 12 AWG White, Single Ended ( 22 Amps)
7-252912000-072
Power Patchcord
Power, Patchcord, Receiver, 72", Micro Power, 12 AWG White, Single Ended ( 22 Amps).
-
Product
Power, Patchcord, Receiver, 72", Mini Power, 16 AWG White, Single Ended (19 Amps)
7-234916000-072
Power Patchcord
Power, Patchcord, Receiver, 72", Mini Power, 16 AWG White, Single Ended (19 Amps).
-
Product
Power, Patchcord, ITA, 72", High Power, 2 AWG, to Ring Terminal (150 Amps)
7-222902688-072
Power Patchcord
Power, Patchcord, ITA, 72", High Power, 2 AWG, to Ring Terminal (150 Amps).
-
Product
10 MHz to 40 GHz LAN Wide Dynamic Range Average Power Sensor
L2054XA
Power Sensor
The Keysight L2054XA is a fast, accurate and wide dynamic range 10 MHz – 40 GHz LAN average power sensor.
-
Product
Waveguide Power Sensor
E8486A
Power Sensor
Keysight waveguide power sensors are fully compatible with Keysight EPM (E4418B/19B, N1913A/14A), EPM-P (E4416A/17A) and P-Series (N1911A/12A) power meters. The V8486A and W8486A are also compatible with the discontinued or obsolete power meters such as 435B, 436A, 437B, 438A, 70100A, E1416A, E4418A, and E4419A power meters.
-
Product
Peak And Average Power Sensor, 50 MHz - 6 GHz, 5MHz Bandwidth
E9323A
Power Sensor
The E9323A power sensor has a 5 MHz video bandwidth and is ideal for time-gated peak, average and peak-to-average ratio power measurements on W-CDMA wireless formats such as cdma2000.
-
Product
Power Supply, 80 V, 65 A, 5,200 W
N8758A
Power Supply
Keysight basic DC power supplies offer essential features for a tight budget. The Keysight N8758A is an 80 V, 65 A, 5,200 W, single-output power supply in a small 2U package. It offers flexible AC input options, analog / resistance control of output voltage and current, and parallel and series connection of multiple supplies to achieve more output current or voltage.
-
-
Product
10 MHz – 6 GHz USB Power Sensor
U2001H
Power Sensor
U2001H USB power sensor measures average power over the frequency range 10 MHz to 6 GHz and power range -50 dBm to +30 dBm.
-
Product
DC Power Supply Series
HMC804x
DC Power Supply
One, two or three channels – the R&S®HMC804x DC Power supplies with their specifications and wide range of functions are ideal for use in development labs and industrial environments. Thanks to their high energy efficiency, the power supplies remain cool and quiet, even at maximum load. Practical interfaces and connectors allow users to work quickly and conveniently with the R&S®HMC804x. Comfort functions enable the instruments to be used in special applications.
-
Product
Power Device Analyzer / Curve Tracer For Circuit Design
B1506A
DC Power Analyzer
The Keysight B1506A Power Device Analyzer / Curve Tracer for Circuit Design is a complete solution that can help power electronic circuit designers maximize the value of their power electronics products by enabling them to select the correct power devices for their applications. It can evaluate all relevant device parameters under a wide range of operating conditions, including IV parameters such as breakdown voltage and on-resistance, as well as three terminal FET capacitances, gate charge, and power loss. The B1506A Power Device Analyzer/Curve Tracer for Circuit Design meets and exceeds all curve tracer capabilities.
-
Product
High-Performance Autoranging DC Power Module, 20V, 50A, 500W
N6755A
Power Module
The Keysight N6755A is a 500 W high-performance, autoranging DC power module that provides low noise, high accuracy and programming speeds that are up to 10 to 50 times faster than other programmable power supplies. Optional high-speed test extension offers an oscilloscope-like digitizer that increases measurement accuracy when viewing high-speed transient or pulse events within the device-under-test (DUT).
-
Product
USB Power Sensor, 50 MHz to 24 GHz
U2002H
Power Sensor
Measure average power over the frequency range 50 MHz to 24 GHz and power range -50 dBm to +30 dBm.
-
Product
Mini Power, Receiver, 50u Gold (22 Amps). 18 AWG Twisted Pair Red/Black (5 Amps). Banana Plug Black, Banana Plug Red, 41"
7-242418000-041
Power Patchcord
Mini Power, Receiver, 50u Gold (22 Amps). 18 AWG Twisted Pair Red/Black (5 Amps). Banana Plug Black, Banana Plug Red, 41"
-
Product
Power Splitter, DC to 50 GHz
11667C
Power Splitter
The Keysight 11667C power splitter is recommended when making wideband ratio measurements using a Keysight 8757 scalar network analyzer. This two-resistor type power splitter provides excellent output SWR at the auxiliary arm when used for source leveling or ratio measurement applications. The tracking between output arms over a frequency range from dc to 50 GHz allows wideband measurements to be made with a minimum of uncertainty.
-
Product
RF Limiter, 10 Hz to 1800 MHz
11867A
Power Limiter
11867A RF limiter can be used to protect the input circuits of spectrum analyzers, counters, amplifiers, and other instruments from high power levels with minimal effect on measurement performance. This limiter (10 Hzto 1800 MHz) reflects signals up to 10 watts average power and 100 watts peak power. Insertion loss is less than 0.75 dB.
-
Product
DC/DC Power Supply
PCM-DC-AT512-P
DC Power Supply
WINSYSTEMS’ PCM-DC-AT512-P is a triple output, DC/DC power supply that can mount anywhere in a PC104 stack. It features a very wide voltage input range from 10 to 50 volts DC. This allows the unit to operate with 12, 24, or 48 volt battery or distributed DC power systems. It opens up a wide array of applications including transportation, Mil/ COTS, security, solar-powered, and telecommunications.
-
-
Product
Optical Head Interface
N7749C
Optical Power Meter Interface
The N7749C optical head interface can control two or four 8162-C series optical power meter heads. Readout is supported over LAN and USB interfaces with a built-in web-browser GUI and the SCPI command set common to Keysight optical power meters.
-
Product
Power Supply, 80 V, 42 A, 3360 W
N8738A
Power Supply
Keysight's basic DC power supplies offer essential features for a tight budget. The Keysight N8738A is a 80 V, 42 A, 3360 W, single output power supply in a small 2U package. It offers flexible AC input options, analog/resistance control of output voltage and current, as well as parallel and series connection of multiple supplies to achieve more output current or voltage.
-
Product
EPM Series Dual-Channel Power Meter
N1914B
Power Meter
The N1914B EPM series dual-channel average power meter provides repeatable and reliable results for bench/rack and field applications.
-
Product
Digital Power Meter
Power Meter
Digital Power Meter is designed for single-phase measurements of AC power signals and related parameters common to most electronic products. Instead of traditional analog measurement circuits, the 66200 uses state-of-the-art DSP digitizing technology.
-
Product
Power, Patchcord, Receiver, 72", Mini Power, 8 AWG White, Single Ended
7-236908000-072
Power Patchcord
Power, Patchcord, Receiver, 72", Mini Power, 8 AWG White, Single Ended.
-
Product
P-Series Modular Power Meter (LXI Compliant)
N8262A
Power Meter
The Keysight N8262A P-Series modular power meter enables LAN-based automated measurements of peak, peak-to-average ratio and average power. The N8262A enables fast, efficient, and cost-effective creation and reconfiguration of your ATE system. Owing to LXI test standardization and its interoperability with existing test assets, your system can be up and ready in no time.
