GPS Simulators
-
Product
GPS Simulator
ADIVIC MP6220
Simulator
Multi-channel GPS simulator for GPS receiver position fix testIndividual channel is power adjustableSingle channel mode for receiver S/N ratio testTunable power output level from -160dBm to -55dBm
-
Product
Radio Link Simulator
RLS-2100
-
Square Peg Communications Inc.
It is the most comprehensive, with unparalleled impairment simulation, real-time multi-satellite orbit calculation, full motion support and integrated GPS simulators. It is the most flexible, providing end-to-end or single link simulation of wideband terrestrial and satellite networks, satellite selection via open standard interfaces, and facilities to enable seamless integration into more complex test beds if required. It supports the highest bandwidth and has an intuitive, user-friendly interface. And it does it all in one box.
-
Product
GPS Simulator
MVT-NSSG
-
The Navigation Spread Spectrum Generator can be used for precise GPS M-Code interference tests with existing GPS C/A and P/Y receivers. The simulator is capable of generating all the current GPS signals simultaneously with the new modernized signals and codes. Optional models can be configured with unique user defined signals, such as would be required for GLONASS.
-
Product
STANAG3910 Test And Simulation Module – Rafale – For PCI Express
APEX3910-EN
Simulator
Single Stream STANAG3910 Test and Simulation module – Rafale – for PCI Express with 1 dual redundant HS/LS channel and onboard Electrical Front End (EFE). The APEX3910-EN is a functional replacement for APE3910-EN.
-
Product
LED Load Simulator
63110A/ 63113A/63115A
Simulator
As shown on the V-I curve in figure 1, the LED has a forward voltage VF and a operating resistance (Rd). When using a resistor as loading, the V-I curve of the resistor is not able to simulate the V-I curve of the LED as shown in blue on figure 1. This may cause the LED driver to not start up due to the difference in V-I characteristic between the resistors and the LEDs. When using Electronic Loads, the CR and CV mode settings are set for when the LED is under stable operation and therefore, is unable to simulate turn on or PWM brightness control characteristics. This may cause the LED driver to function improperly or trigger it’s protection circuits. These testing requirements can be achieved when using a LEDs as a load; however, issues regarding the LED aging as well as different LED drivers may require different types of LEDs or a number of LEDs. This makes it inconvenient for mass production testing.
-
Product
Single Stream STANAG3910/EFEX Test & Simulation Module For 3U PXI Express/Compact PCI Express
ACE3910-3U-1
Simulator
STANAG3910/EFEX Test and Simulation module for CPCIe/PXIe (3U) with 1 Dual Redundant HS/LS channel. Onboard Fibre Optic Front End (FOFE). Easily select between EFAbus and EFEX modes for Tranche II Eurofighter.
-
Product
PXI/PXIe LVDT/RVDT/Resolver Simulator Module, 2-Banks
43-670-003-AABBCC
Simulator
The 41/43-670-003 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel
41-752A-002
Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Dual Port Simulator Fiber Channel PXIe Module
PXIe-FC4 Simulyzer
Simulator
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
Product
Solar Array Simulator Module 0-130V, 0-8A, 1kW
MP4362A
Simulator
The Keysight MP4362A is a 0-130V, 0-8A, 1kW solar array simulator DC power module that simulates the output characteristics of a solar array.
-
Product
PXI RTD Simulator Module, 20 Channel, PT100
40-263-101
Simulator
The 40-263-101 is a 20-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PXI/PXIe LVDT/RVDT/Resolver Simulator Module
41-670-XYZ-AABBCC
Simulator
The 41/43-670 range is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers. Available with up to four banks, each bank is capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 4 channels of 5 or 6-wire or 8 channels of 4-wire.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCI With 2 Or 4 CAN Bus Nodes
ACP825-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for PCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825-x PCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Thermocouple Simulator Module for SLSC
Simulator
Bloomy’s 8-Channel Thermocouple Simulator Module provides eight channels of galvanically-isolated thermocouple simulation and simulates types E, J, K, M, N, and T thermocouples. High-precision digital-to-analog converters which are isolated from each other and from system power provide sub-microvolt resolution and accuracy. Built-in switching provides open-circuit faults as well as switching to system calibration resources.
-
Product
PXI RTD Simulator Module 12-Channel PT1000
40-262-202
Simulator
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
Product
Synchro Simulator
SPA-CASE
Simulator
Computer Conversions Corporation
The Synchro Simulator has two modes of operation: Static and Dynamic. The mode of operation is selected by the position of the mode switch. In the static mode, the thumbwheel switches select the output angle. In the dynamic mode, the speed and direction switches determine the rate and direction of synchro outputs. Self test circuitry continuously monitors and displays the output.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 32 Channel
41-761-001
Simulator
The 41-761-001 is a low voltage 32-channel output module ideal for simulating theoperation of a thermocouple, also available with 24, 16 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
Product
PXI/PXIe LVDT/RVDT Simulator Module, 2-Banks
41-670-103-AABBCC
Simulator
The 41/43-670-103 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 2 channels of 5 or 6-wire or 4 channels of 4-wire.
-
Product
PXI Millivolt Thermocouple Simulator Module - 8 Channel
41-760-004
Simulator
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 26 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
Solar Array Simulator DC Module, 65V, 8.5A, 510W
E4361A
Simulator
The Keysight E4361A is a 510W solar array simulator DC power module that simulates the output characteristics of a solar array. The E4361A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin etc.). The E4360 gives you the flexibility to operate it in two ways:
-
Product
Dual Port Simulator Fiber Channel PCI-X Module
PCI-X-FC4 Simulyzer
Simulator
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
Product
PXI RTD Simulator Module, 20 Channel, PT500
40-263-102
Simulator
The 40-263-102 is a 20-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Single, Dual Or Quad Stream MIL-STD-1553A/BTest And Simulation Module For PCI
APXX1553-x
Simulator
MIL-STD-1553 Test and Simulation Module for PCI with 1, 2 or 4 Dual Redundant channels (APXX1553-1, APXX1553-2, APXX1553-4) plus 8 programmable discrete Input/Output channels. A unique feature of AIM’s APXX1553-x module is the option for the MILScope™ capability. Models APXX1553-1-DS/APXX1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
Product
PXI RTD Simulator Module, 4 Channel, PT100
40-263-501
Simulator
The 40-263-501 is a 4-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Solar Array Simulator Auto-Ranging Module 0-160V, 0-10A, 1kW
MP4361A
Simulator
The Keysight MP4361A is a 1000 W solar array simulator DC power module that simulates the output characteristics of a solar array. The MP4361A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin, etc.).
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 8 Channel
41-761-004
Simulator
The use of two wire outputs and isolation from ground ensures that the 41-761 can be used to accurately simulate low voltages even in the presence of common mode voltages in the system. Each Vcold connection is independent permitting the 41-761 to be connected to multiple cold junctions.
-
Product
Radar Target Simulator
E8707A
Simulator
Rapid developments in the autonomous vehicle and demand for greater safety features is fueling the need for more sensitive and accurate automotive radar technology being deployed in advanced driver assistance systems (ADAS). With its rich expertise in radar test technology, Keysight now offers the E8707A radar target simulator to help automotive electronics manufacturers confidently simulate radar targets in various realistic scenarios.
-
Product
LVDT/RVDT Simulation Board
75DL1
Simulator
The 75DL1 is a cPCI LVDT/RVDT Simulation Board that provides eight 2-wire or four 4-wire transformer isolated programmable outputs. It provides wrap-around self-test, PXI compatibility, optional Excitation Supply, and is available for Military or Commercial applications.
-
Product
Programmable S/R Standard & Simulator
5300
Simulator
NAI’s 5300 Synchro/Resolver Standard & Simulator is a laboratory-grade, programmable instrument. This model can be used as a true Synchro/Resolver standard for calibrating and testing Automatic Test Equipment (ATE) for Calibration/Metrology Labs, and for Engineering Design and Production Test environments. It can also be used to measure Angle Position Indicators (API) and Synchro-to-Digital converters for static or dynamic characteristics. This model also may use an external reference waveform.





























