-
Product
Measuring Systems For Beverage Can Manufacture
Cross Hatch Machine
-
Optik Elektronik Gerätetechnik GmbH
Uniform crosshatch pattern on a punch, specific for the beverage can industry.
-
Product
Ultrasonic Clamp-On Flow Sensor
SEMIFLOW CO.65
-
SEMIFLOW CO.65 non-contact clamp-on flow sensors are ideal to measure abrasive, adherent, corrosive, and ultra-pure liquids on rigid plastic tubes and pipes used in the semiconductor industry. Equipped with an integrated electronic unit, they function as a complete flow meter in the size of a small transducer without an external board or transmitter.
-
Product
PXIe-6375, 208 AI (16-Bit, 3.8 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module
783634-01
-
PXIe, 208 AI (16-Bit, 3.8 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6375 offers analog I/O, digital I/O, and four 32‑bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6375 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
-
Product
Automatic Extensometer
SIE-560A/560SA
-
To determine the suitability of a material for an application where it is under load, measuring its elongation is important. Measuring elongation enables determination of the elastic modulus (reversible elongation in the elastic region) by measuring the small initial elongation range, and determination of elongation at specimen failure, by measuring larger irreversible elongation in the plastic region. Shimadzu’s SIE-560A series automatic extensometers accomplish both of these measurements with high accuracy, and provide automated functions that increase testing efficiency and test reproducibility. Ideal for testing a wide variety of materials, including metallic materials, plastics, and composites, the SIE-560A series complies with ISO 527, JIS K 7161, and ASTM D638 standards for plastics tensile testing. In addition, the SIE-560A series supports strain-rate controlled metallic material tensile testing measurements specified in ISO 6892, JIS Z 2241, and ASTM E4
-
Product
Vibrating Sample Magnetometer
VSM-5
-
This type measures on variations of temperature as well as yet normal room temperature under vacuum and in gas by the use of electromagnet.
-
Product
Amp Booster
CHI680C
-
With the CHI680 Amp Booster, the current can be measured up to 2 A. The CHI680 is compatible with Model 600, 600A, 600B, and 600C series of instruments. You can stack the CHI600/A/B/C and the CHI680 together.
-
Product
Dual Input Thermometer
Si-TT3
-
The palm-sized Sauermann Si-TT3 dual input thermometer easily measures K thermocouple temperature.
-
Product
DIGITAL PHASE ANGLE METER
GF211B
-
Beijing GFUVE Electronics Co.,Ltd.
GF211B onsite handheld digital phase angle meter can measure alternating voltage, alternating current, frequency, phase angle, active/reactive power, power factor and so on.
-
Product
Wire Crimp Pull Tester (Motorized)
WT3-201M
-
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
Product
Temperature Logger for Thermistor Probe
TGP-4020
-
Loggers with probes can be used to record temperature in awkward to reach areas or applications where a fast time response is required. A versatile range of probes are available for this unit and can measure between -40 to +125C. Like the logger, probes are waterproof to IP68.
-
Product
Cryogenic Temperature Sensors
Ultra-low temperature Rox™
-
With the amazing progress made by dilution refrigerator manufacturers to push base temperatures well below 10 mK, the need for accurate, simplified temperature measurements continues to grow. The RX-102B-RS meets this need as a resistive temperature device (RTD) that maintains sensitivity well below 10 mK.
-
Product
Ammeter
AC Moving Iron Meter
-
Moving-iron instruments are generally used to measure alternating voltages and currents. In moving-iron instruments the movable system consists of one or more pieces of specially-shaped soft iron, which are so pivoted as to be acted upon by the magnetic field produced by the current in coil.
-
Product
ANSI Meters
-
Shenzhen Star Instrument Co., Ltd.
Directly connected emergy meter measures active, reactive and apparent energy by multi tariffs while recording max demand and events. It has an optical port and supports RF/PLC communication, which complies and ANSI standard.
-
Product
Dynamic Gravity Meter
TAGS-7
-
TAGS-7 represents the latest development in a long line of LaCoste-based airborne gravity systems, stretching back to the first successful airborne gravity flights in 1958 and building on the success of the TAGS System. For over 50 years, LaCoste gravimeters have acquired hundreds of thousands of line kilometers of gravity data during academic, government, and commercial surveys. TAGS-7 blends the latest in GPS and data acquisition technology with the solid foundation of the LaCoste dynamic gravimeter.TAGS-7 is an upgrade to the TAGS-6 gravity meter, and is designed specifically for airborne operations. The system incorporates a time-tested, low-drift, zero-length-spring gravity sensor mounted on a gyro-stabilized gimbal platform. The sensor has a worldwide gravity measuring range (no reset necessary) of 500,000 milliGals.
-
Product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30001-JDP
-
Breakout board for the MAX31855J digital thermocouple interface IC. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header and four mounting holes for standoffs and 4-40 screws. It does not contain a mini thermocouple connector.
-
Product
Fixed Attenuators
-
In circuits are used to lower voltage, dissipate power, and to improve impedance matching. In measuring signals, attenuator pads or adapters are used to lower the amplitude of the signal a known amount to enable measurements, or to protect the measuring device from signal levels that might damage it.
-
Product
Acceleration Sensor
-
Vernier Software & Technology, LLC
This 3-axis acceleration sensor has two acceleration ranges plus an altimeter and a 3-axis gyroscope. An additional channel measures the angle of the sensor’s long axis. Go Direct Acceleration Sensor connects wirelessly via Bluetooth® or wired via USB to your device.
-
Product
Light I-V Testing for Modules
FMT-500
-
Advanced analysis of solar modules including light I-V and Suns-Voc data. Capability to accurately measure high-efficiency modules.
-
Product
Conductive Emission Measurement
-
Holland Shielding Systems B.V.
On site testing for exposure limits in working conditions to any international standard. This involve pacemakers and HSE Heath and safety executive, invitarisations worldwide.
-
Product
Observational Systems: Profiling Floats
-
Autonomous profiling floats are revolutionizing the way scientists study the ocean. Before the first profiling float entered the water, our ability to measure climate, biological, and chemical trends was limited in scope while large-scale studies were a costly endeavor.
-
Product
Isoperibol Calorimeter
AC500
-
The AC500 determines calorific value, a key indicator of quality and value in solid and liquid fuels, through measurement of the heat released after combustion of a sample. This stand-alone benchtop unit uses a fully-integrated circulation system for a compact footprint—no additional heaters or coolers required. An integral water-measuring station simplifies sample preparation, and a Windows®-based operating system uses an electronic thermometer accurate to 0.0001°C to measure temperature every six seconds. Two-channel correction is possible through constant temperature monitoring in both the outer jacket and the calorimeter proper.
-
Product
Phased Array
-
Phased array machines provide precise measurement with the most reliable results. Our range of phased array devices produce accurate, detailed cross-sectional pictures of internal structures at fast inspection speeds.
-
Product
Ultra Fast Line Sensors
µsprint
-
With an unparalleled scanning rate, the µsprint sensors are the ideal tool for quality and process control with high throughput rates and precise measurements. As a standalone solution for laboratories, with machine safety enclosure for industrial production environments, or as an OEM solution – the μsprint technology can be inegrated flexibly everywhere.
-
Product
Web Sensor
T3511
-
Web Sensor with relative humidity and temperature probe. The device is supplied with T+RH probe on the cable. High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Near Field Micro Probe Sets
-
The near field probe is designed for a high-resolution measurement of electrical near fields.
-
Product
Handheld Water Quality Meters
LAQUA PC220
-
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers)- 0.01 pH resolution- Offset and average slope display- ORP calibration option- Automatic / manual temperature compensation and temperature calibration function- Automatic (up to 4 points) and manual (up to 5 points) conductivity calibration- Adjustable reference temperature and temperature coefficient- Adjustable cell constant and selectable measurement unit- Conductivity and total dissolved solids (TDS) conversion- Four (4) TDS calibration curves for wide range of applications: EN27888, Linear, 442, NaCl- Two (2) salinity calibration curves: NaCl, Seawater- With real-time clock and date/time stamp for GLP compliance- Auto log data; built-in memory can store up to 1000 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached - Monochrome LCD with white LED backlight: 50 x 50 mm- Phono jack output for connecting meter to computer via PC (USB) cable for data collection and to printer via printer (RS232) cable for printout - Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrodes and calibration solutions in carrying case- 3 years meter warranty
-
Product
Vibration Meter
Revo
-
The Revo Vibration Meter has been specifically designed for Hand-Arm Vibration and Whole Body Vibration measurements.
-
Product
Antenna Test Chambers
-
Special design for low PIM antenna measurements Shielding > 90 dB Frequency Range 700/1000 MHz to 6000 MHz Residual PIM < -165 dBc (@ 2 x 43 dBm) Up to 6 antenna ports for multi-band and MIMO antennas Standard models for antennas up to 2.7 m length Customized solutions available on request
-
Product
Hydraulic Force Gauges
-
AMETEK Sensors, Test & Calibration
The hydraulic force gauges from Erichsen are a low cost solution for obtaining general force measurements. With a wide range of styles and sizes, these force gauges are popular in many industries ─ particularly for use in hazardous environments.
