Filter Results By:
Products
Applications
Manufacturers
Potentiometers
Measure the voltage in a circuit or function as voltage dividers.
See Also: Programmable Resistors
-
product
Configurable Reostat or Potentiometer Module
YAV90084A
4x 8-Bit 1KOhm reostat4x 8-Bit 40 Ohm reostat2x 8-Bit 5 MOhm reostat10x Electronic Potentiometer 8-bit resolution -256 steps- with build-in self test10x Voltage to current source 0(4)..20mA10x Analog Outputs (buffer for voltage or frequency)36-Ch Test Point voltage divider2xCAN Bus Channels Terminators testerExpandable with NI PXI-6723 and PXI-6345.
-
product
Motorized Potentiometer
Panel Mounting
INELTA Sensorsysteme GmbH & Co. KG
* Panel mounting* For multiturn potentiometer only* Suitable as:* setpoint device or rotary actuator* Compact in design* Robust aluminium housing* Gear safety clutch
-
product
PXI Resistor Module 48-Channel (no resistors fitted)
40-280-121
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
product
Turns-Counting Dials
Turns-counting dials are designed for use with precision rotary potentiometers or other types of panel controls where a turns-indicating device or an adjustment setting/locking device is needed. These devices are available to fit various shaft sizes in digital or concentric scale (analog) readout options.
-
product
Life Cycle & Fatigue Testers
Switches can use all these operations. Membrane switches, keyboards and keypads will all require a push with a known force. On/Off switches will combine a push and a pull or possibly push on, push off. A rocker switch and toggle switches will require a push in two different places. Rotary switches (and volume controls, potentiometers) need to be rotated clockwise and counter clockwise The standard life cycle and fatigue tester the B886 Simon System has been designed for life cycle and fatigue testing of switches, membrane switches, keyboards and keypads. It contains all the components needed to life and fatigue test a products that need to be pushed. We can also supply different actuators for a push, pull, rocker, toggle, volume control or rotary switch.
-
product
Universal Transmitter
Knick Elektronische Messgeräte GmbH & Co. KG.
Universal Transmitter for temperature, load cells / strain gauge, potentiometer and resistance in 6 mm housing. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
product
Gear Shift Sensors and Displays
Variohm can offer compression/tension gear shift load cells, as well as gear number displays which accept a rotary potentiometer input to define gear position.
-
product
Dual Output Digital Lab Series Regulated DC Power Supply – Upto 1280W
- 300W to 1280W different combination- High current density.- 19″ rack adaptable -3U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation- Optional, at extra cost- Over voltage protection- 19″ rack mounting- Analogue programming and monitoring for V&I
-
product
PXI Potential Divider Module 12-Channel (no resistors fitted)
40-282-021
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
product
Power Monitor, AC-Powered, Field Adjustable
YMA/YQA
NAI's YMA and YQA Power Monitors are used to monitor voltage, frequency, and phase characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.High and low voltage and frequency limits, and "pick-up" and "drop-out" time delay are field-adjustable using potentiometers. These power monitors are ideally suited for rugged defense and industrial applications.
-
product
Self Powered Active Load
TBOH02
The TBOH02 is a self powered, precision active load. It does not need a separate supply voltage and operates as low as 2V. Its features include constant resistance and constant current mode. A 10 turn potentiometer with dial, a range switch and a precision reference enable accurate setting of current or resistance. Furthermore it can be controlled by an external voltage.
-
product
Capacitive Sensors
*High noise immunity*Sensing range adjustable by means of potentiometer or teach button*Plastic or metal housings for different applications*Sensors for position and level detection*Accessories for mounting on tanks or sight glasses
-
product
PCI Standard Programmable Resistor Cards
Pickering's PCI Standard Programmable Resistor Cards include fully programmable resistor and potentiometer cards for applications such as sensor emulation that require fine adjustment with a resolution down to 0.25 Ohm. All of our Programmable Resistor Cards can easily be formed to make Programmable Potentiometers by connecting two channels in series, using the unconnected terminals as the A and B connections and the link between the two channels as the wiper connection.
-
product
PXI Potential Divider Module 24-Channel (no resistors fitted)
40-282-121
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
product
PXI Potentiometer Module 4x12 Bit, 0 Ohm to 4K Ohm
40-296-121-4/12
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
product
Troubleshooting Track Circuit Simulators
14900 Series
The 14900 seriesTrack Simulator features a front panel with standard set up resistors and terminals and electrically conductive model track to simulate a track circuit suitable for instructional and hands-on training purposes. A locked drawer provides additional switches, potentiometers, and controls that allow selective implementation of many faults commonly found in typical track circuits.
-
product
4 2/3 Digit Potentiometer Meter (1/32 DIN)
CS3-PM
CS3-PM Potentiometer Indicator has been designed with high accuracy, display, controller, remote communicationsA compact body design for small equipment, laboratory instrument, and others.Also are available with relay output, analog output, RS485 Modbus RTU communication to cover a wide range of applications.
-
product
PXI Potentiometer Module 2x16 Bit, 0 Ohm to 65K Ohm
40-296-021-2/16
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
product
High Power Digital Lab Series Regulated DC Power Supply – 3000W
- 3000W different combination- High current density.- 19″ rack adaptable -5U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation Optional, at extra cost- Over voltage protection- 19″ rack mounting
-
product
Economic Type Potentiometer Indicator
CS1-PM
CS1-PM economic type Potentiometer Indicator has been designed with high accuracy measurement, display and communication of resistance (3 wires) as like as Positioner.The meter supports Field Calibration function. It can be calibrated with sensor (Potentiometer) to meet machinery structure.They are also available 1 option of 1 Relay outputs, 1 Analogue output or 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of machinery and testing equipments applications.
-
product
Signal Conditioning & Control
Offering a wide variety of products from amplifiers and comparators to redrivers, microcontrollers, data converters (ADC) and digital potentiometers (POTs).
-
product
Industrial Automation
NAI offers a variety of resolver-based Astrosystems motion control solutions for the packaging, material handling, and automated manufacturing industries. Specifically designed for rugged defense and industrial applications, our innovative product lines include single- and multi-axis synchronizers, limit switches, encoders, position sensors, and potentiometers.
-
product
Amplifier Built-in Ultra-compact Laser Sensor
EX-L200
Panasonic Industrial Devices Sales Company of America
The EX-L200, the one of the world’s smallest Laser Sensors with a built-in amplifier, is designed to detect minute objects with utmost accuracy. Despite its miniature size, the Thru-Beam Type (EX-L211) can detect minute objects with a diameter of just 0.3mm, and the Spot Reflective Type (EX-L221) can even detect gold wire whose diameter is a mere 0.01mm. To facilitate solving application tasks, these sensors come equipped with a Potentiometer and two indicator LEDs. For the Thru-Beam Type, reflective material on the receiver allows users to visualize the laser beam, easing beam-axis alignment.
-
product
PCI High Density Potentiometer Card 1-Channel, 24-Bit, 0 To 16M Ohm
50-296A-021-1/24
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Resistor Module Dual 24-Channel (no resistors fitted)
40-281-121
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
product
Input Devices
Panasonic Automotive & Industrial Systems Europe GmbH
Panasonic's Electromechanical Components are used to convert mechanical movement into electrical signals. These products, including switches, encoders, and potentiometers, are used in everyday devices at the point of user interaction.
-
product
Rotary Position Sensors For Motorsport
Variohm offer a range of Rotary Position Sensors For Motorsport including rotary potentiometers and hall effect sensors. They are suitable for use in Morotsport application such as pedal, steering and gearbox applications.
-
product
DC Precision Measuring
Precision instruments for calibrating and monitoring. Our line of Precision Bridges, Decade Boxes, Galvanometers, Potentiometers, and standard high precision resistors, allow customers the accuracy and quality demanded in a precision device.
-
product
PXI Potentiometer Module 1x24 Bit, 0 Ohm to 16M Ohm
40-296-021-1/24
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
product
PCI High Density Potentiometer Card 2-Channel, 16-Bit, 0 To 65k Ohm
50-296A-021-2/16
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
