Current Transformer Test
measures insulation, excitation current, turns ratio, winding polarity saturation and/or winding resistance. Current Transformers
See Also: Transformer Test, Transformer Testers, Current Transformer Test Set
-
Product
EMS Test System
TS9982
Test System
The R&S®TS9982 is the base system for conducted and radiated EMS measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for complete motor vehicles with 200 V/m.
-
Product
Automated Test Equipment
test
These systems test semiconductor performance and quality with industry-leading precision and cost efficiency. Robust support for semiconductor design evaluation, volume production ramps, and yield improvement.
-
-
Product
VLSI Test System
3380P
Test System
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (512 I/O pins to test 512 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
sbRIO-9265, Non-Enclosed, 4-Channel C Series Current Output Module
780921-01
Current Input Module
Non-Enclosed, 4-Channel C Series Current Output Module - The sbRIO‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The sbRIO‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity. Non-enclosed modules are designed for OEM applications.
-
Product
Photodiode Burn-in Reliability Test System
58606
Test System
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
Product
HPC High Current Probe
HCP-13
High Current Probe
Current Rating (Amps): 15Average Probe Resistance (mOhm): 25Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 250,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
BMS Manufacturing Test System
Test System
The Battery Management System (BMS) Manufacturing Test System performs functional testing of product during end-of-line manufacturing. The system hardware includes all instrumentation to test a BMS, including multiple cell simulators, a mass interconnect for quick product transition and bed-of-nail fixtures to ensure less down time, higher throughput, and easy maintenance. The system application easily integrates into manufacturing processes, provides a method to test multiple product types, and optimizes tests to ensure only good product is released from manufacturing.
-
Product
NTS Platform
Test Platform
Manufacturers all over the world are leveraging our NTS platform for products with rotating or otherwise moving parts, or produce sounds. Typical applications include mass production of air conditioning units, pumps or small electric motors, where errors in assembly can cause malfunctions or significantly shorten service life. This test platform is customized to your specification and application. Feasibility studies are available to ensure your solution is exactly what you are looking for.
-
Product
Communications Test System for Frontline Diagnostics
ATS3000P
Test System
The ATS3000P is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000P also includes the sophisticated IF and baseband I/Q DigitalSignal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easyto-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets are available for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
Product
Hybrid Single Site Test Handler
3110
Test Handler
Chroma Hybrid Single Site Test Handler 3110 is a full range ATC (Active Thermal Control) test handler capable of handling device bodies up to 120x120mm with 450kg force load.
-
Product
In-Circuit Test System Calibrations
Test System
Regular calibration is essential to ensure accuracy and reliability in testing. Forwessun offers precise calibration services tailored to your test systems, verifying that all components meet industry standards. Our calibration services maintain peak accuracy and compliance, so you can be confident in your system’s performance for any testing application. Choose from one-off calibrations or scheduled service contracts to meet your needs.- HP3070 - Agilent- Keysight - GenRad- Teradyne
-
Product
PXIe Optical Test Modules
Test Module
Coherent Solutions’ expanding portfolio of PXIe optical test modules bring a wide range of new mixed-signal test capabilities to the PXI platform. The new modules offer seamless integration with PXI Platform and deliver reliable and repeatable results across a wide range of optical and mixed-signal test applications.
-
Product
6TL60 Rotary Test Handler
H79006010
Test Platform
6TL60 has been designed according to the 6TL philosophy, following the concepts of flexibility, modularity and scalability, and with the aim of improving production efficiency as well as increase production capacity and reduce costs.The 6TL60 is the best production solution to automate test processes to reduce the cycle time and the footprint used in the manufacturing plan
-
Product
Brute High Current Probe
P4301-1R
High Current Probe
Current Rating (Amps): 50Current Rating Remark: 40 Amps for BeCu plungersAverage Probe Resistance (mOhm): 5Test Center (mil): 300Test Center (mm): 7.62Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 1,750Overall Length (mm): 44.45
-
Product
Mini LED Backlight Module Automatic Optical Test System
7661-K003
Test System
Chroma 7661-K003 Mini LED Backlight Module Automatic Optical Test System contains a 71803-2 2D color analyzer to measure chromaticity and brightness
-
Product
Battery Management (BMS) Environmental Test System
Test System
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
-
Product
sbRIO-9253, Non-Enclosed, 50 kS/s/ch, 24-Bit, 8-Channel C Series Current Input Module
787433-01
Current Input Module
Non-Enclosed, 50 kS/s/ch, 24-Bit, 8-Channel C Series Current Input Module - The sbRIO-9253 is an 8-channel analog input module for CompactRIO Single-Board Controller that provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. This module includes diagnostic functionalities to ensure nominal system operations with open-channel detection, power supply detection, and configurable thresholds. You can view the status of each channel and the power supply with eight LEDs. The sbRIO-9253 also features programmable hardware filters for your applications, such as specific Butterworth and comb filters that you can use to reduce the noise in your system.
-
Product
PCIe 2.0 Test Platform
PXP-100B
Test Platform
The Teledyne LeCroy PXP-100B Test Platform provides a convenient means for testing PCIe 2.0 add-in cards with a self-contained portable and powered passive backplane. The PXP-100B provides power required for both cards under test, and an interposer can be used for connection to a protocol analyzer. As an alternative to an interposer, the PXP-100B includes two mid-bus probe footprints to allow connection to an analyzer via a mid-bus probe.
-
Product
NI-9203, 200 kS/s, ±20 mA, 8-Channel C Series Current Input Module
779516-01
Current Input Module
200 kS/s, ±20 mA, 8-Channel C Series Current Input Module - The NI‑9203 is intended for high-performance control and monitoring applications. It features programmable input ranges and variable connectivity options. To protect against signal transients, the NI‑9203 includes a channel‑to‑earth ground double‑isolation barrier (250 Vrms isolation) for safety and noise immunity.
-
Product
NI-9208, 500 S/s, ±20 mA, 16-Channel C Series Current Input Module
780968-01
Current Input Module
500 S/s, ±20 mA, 16-Channel C Series Current Input Module - The NI‑9208 is designed with industrial systems in mind. It includes a high-resolution mode with 50/60 Hz rejection to remove low frequency noise. It has high-channel density to reduce the number of modules needed, which leaves slots open for other measurement types or for reducing the overall per channel cost of the system. The NI‑9208 uses a standard D‑SUB connection for use with cables and connector blocks.
-
Product
Non-Signaling RF Test Platform for Validation & Production
Universal Wireless Tester
Test Platform
Wireless communication standards are increasingly integrated into vehicles as well as smart home and Internet-of-Things applications. They form the basis for connected services, advanced HMIs, and autonomous driving. The combination of constantly evolving standards and the integration of multiple wireless technologies with many RF channels into new product designs means that measurement speed and quality are becoming a priority.
-
Product
Test System
UltraFLEX
Test System
The UltraFLEX test system delivers the power and precision you need for complex SoC devices built for mobile applications, networking, storage or high-end processing. Choose UltraFLEX when your device mix and throughput goals demand the highest speed, precision, coverage and site count.
-
Product
3-Axis Non-Robotic Automated Testing System
AT3
Test Instrument
The Instron AT3 is a space-efficient, highly adaptable 3-axis mechanical testing platform designed for automated execution of tensile, compression, flexural, and lap shear tests. Built to comply with a broad spectrum of ASTM and ISO standards, it’s well-suited for evaluating materials such as plastics, elastomers, thin films, foils, and metals. The system streamlines the entire testing workflow from specimen measurement and handling to strain measurement and specimen disposal—enabling users to load up to 160 samples and let the AT3 take care of the rest. Boost productivity, reduce manual intervention, and achieve consistent, dependable results with every test cycle.
-
Product
Automotive Ethernet Test Fixture
AE6941A
Test Fixture
The AE6941A automotive Ethernet electrical test fixture provides easy access to automotive Ethernet electrical signals so you can perform conformance testing and device characterization quickly and easily.
-
Product
Positioning Test System
TS-LBS
Test System
The R&S®TS-LBS is a comprehensive test solution for network and satellite based location technology testing of wireless devices and chipsets.It is highly configurable for testing various location technologies and uses Rohde & Schwarz location based test systems.The R&S®TS-LBS test system family fulfills the requirements of LBS conformance testing and operator acceptance testing on GSM, WCDMA, LTE and 5G devices and chipsets as well as regulatory testing consisting of adjacent channels and spurious emissions for EN 303 413 receiver testing. It also fulfills the requirements of E112 (EU) 2019/320 testing consisting of GNSS testing such as Galileo and AML mobile testing.
-
Product
EOL RF Functional Test
AS652
Test Platform
With this RF test platform, integrable according to the specific needs of the product, we cover a very wide range of test needs with manual feeding.Ergonomics have been fully observed in the design, including the option of servo adjustment of the working height according to the operator.
-
Product
High Temperature Component Test Fixture
16194A
Test Fixture
Measure both axial/radial leaded devices and SMD within the temperature range from -55 to +200°C.
-
Product
Semiconductor Testers
Test Instrument
Our integrated team of semiconductor test innovators delivers a complete system tailored to achieve your specific objectives, incorporating:Test strategyHardware designSoftware development and integrationManufacturingInstallationProgram managementOngoing support
-
Product
Tabletop Single Site Test Handler
3111
Test Handler
The Chroma 3111 is an automated pick & place handling system ideal for small lot engineering samples and/or NPI test development parts.
